I'm happy with mine that I got at a discounted price. I wish the fans were less loud, but that's an easy upgrade.

Hot soapy water cleans most of the marks, and a good accessory for print removal is an Industrial Razor blade scraper, this gets the remove started cleanly, to be completed with the paint scraper. Also, let the bed cool for PLa print removal with greater ease.

Thank you very much, I thought it was quite thorough and the project timings were helpful but I would have liked them on the technical ones too.

Hi, I bet that blobbing artifact was due to 'resume print after power outage' being enabled. I've seen that causes a slight delay when the printer writes the current position to the sd card, which results in a slight blob.

Take the scraper with a hammer put it on the floor. Put your foot on front of the plate. Take scraper to buttom of back the print or supports. And one hit with with hammer to the scraper pops right off usually.

Printed objects over 100 hours and is really good at maintaining good quality

That T REX skull is badass!!!

I don't want to say that I hate the glass bed, but I do dislike it. I was able to test and review the Max Neo and that was my biggest complaint, the prints stick hard. I did try putting it in the fridge recently and that helped but I don't want to have to pull the bed off and put in the fridge every print. The dual sided PEI sheets are great. Even the Creality E3 Pro PEI coated glass bed is fantastic but not available in the 300x300 size. Hopefully it will be eventually. I wasn't impressed with the manual bed leveling instruction and maybe it was my fault but I scratched the bed with the nozzle when moving to the first corner. It never said to loosen the springs and such. I wished they were a bit more detailed than saying to set Z offset and go to the corners. I thought the menu is a bit watered down vs the E3 Pro but I haven't used the stock firmware in a long time. I hope to be able to do my own firmware for this eventually but don't know what that will entail being a color screen like it is.

Mine started out good two months in the glass bed lost its sickness and nozzle jams up a lot

I connected mine to the PC to print as my Ender killed off my memory card and won't recognise a new one I bought. Though I did catch the USB cable connecting it during a long print and it ended up failing as there was no way to continue, also don't like the USB is the old Mini USB. My main problem is the fan noise but I cannot find any vid showing an upgrade for the Neo Max, they all show the smaller Ender 3s with the power supply on the side vertically where the neo is underneath.

they have it on sale atm £369 to £269

Not a bad printer, but the company support is a 'F'. I bought one of these 2 months ago. Printer 5 rolls of filament with no real issues. I cleaned it after each print, leveled the bed after each print etc etc. Then the other day. I had a 15 hour PLA print going and I checked in on it after 8 hours from my remote app and the printer was moving fine but no filament was coming out. I went to my print room and stopped the job. The hotend had become clogged and the extruder continued to force filament down into the hot end where it built leaked and created a mess of the hot end. It wasn't salvageable by cleaning and so I contacted their support. I am sorry, but it is terrible. This is a $15 part and I am having no luck get then to even understand. This should be a slam dunk - send me another cheap hotend, but no they don't seem to get it. I bought this as an entry level printer and was going to buy another Creality higher end model, but that is not going to happen. Worst support I have even had. I'll send the whole unit back to Amazon.

Nice video and thanks for the info. I have now also bought this 3D printer. Now I wanted to download the Rex skull, but the file no longer seems to be available.

Your review are great. Could you please review the ender 3 V2 neo?

Hi im curious about the magnetic bed im not a glass bed fan any information would be greatly appreciated thank you

hi did you try to print some face for example ,can you make real face to 3d and than printing ?

i cant get a good print out this thing with a 0.6mm nozzle,may as well get rid,i dont want a 0.4mm in it to slow,waste of money,doesnt run half as good as my ender 3 max.

so TPU works on the ender 3 Max Neo? cuz the manual says it doesn't do TPU...

what is the assembled size of the unit?

What size spring steel pei sheet should be used ?

What can I do to get my ender 3 max neo print tpu?

6:30 seems like the small pauses power loss protection causes after each "layer". Did you try with it disabled?

What size filament does it take to

All's mine does is make a screening sound . I can't figure out what's wrong it's brand new

This is my first 3d printer. Have not set it up yet, so they work with iMacs. ?

Can you put a sprite extruder on the neo?

what cura profile we use the ender 3 max?

Extremely disappointed with this printer. I got 2 solid prints out of it before it quit working.

I've had this printer for 6 months. It's more of an upgrade platform with the most bottom tier parts bolted on to get it to print for a few dozen hours. Pretty much everything on it besides the frame and steppers have to be changed in order for it to get reliable high quality prints. New hotend, new extruder, new bed surface, new controller board, better bowden tube, the wiring needs to be ferrule crimped, the power supply cover is lacking venting holes... ok I think I covered everything? You get the idea... if you're not into tinkering and don't have solid CAD knowledge to build new parts, stay away from this thing.

This in not a review. It’s a promotional video 🤦🏼‍♂️

I hate that they are still using the 4.2.2 board it's trash and they know it.

worst printer ever,y axis is very noisy,only prints ok with odd filaments gantry plates are naff,should have got the ender 3 max and upgraded it like my old one.the price on this neo should be around £250