Create a Custom Aluminum Nameplate

Рет қаралды 473

Ай бұрын

This video demonstrates the process to create a nameplate starting with the software. The computer programs used are the following: Inkscape, Winbuilder 3D, and Cura. This video also gives some detail in to pattern preparation and shows how a sand cast mold is constructed. Scrap aluminum is then melted down and poured into the sand mold producing a final product.
Disclaimer--Metal casting is dangerous and can cause injury or death. This video is only for entertainment purposes.
Damon's Metal Casting
damonsmetalcasting@gmail.com
#castingprocess
#sandcasting
#aluminumcasting #metalcasting

Пікірлер: 23

@bobthecomputerguy Ай бұрын

That's some clean casting.

@DamonsMetalCasting Ай бұрын

Thank you very much.

@charliekrauter5176 Ай бұрын

The safety PSA combined with the big hole in the knee of your jeans gave me a chuckle. Truthfully though, I don't do much better. Nice looking pattern. I will definitely try epoxy as a coating. Thanks for making this.

@DamonsMetalCasting Ай бұрын

Yeah those are my casting jeans and they just got worse and worse on the rip. I need more gear right now, the only things that I have protection for is my face, arms and moobs. I should probably pick up an actual full jacket and some leg covers. I can't imagine jeans would save me from +1400F aluminum. I don't think I will be doing any investment casting until I have that gear. If the investment explodes from water or expansion that is a whole lot of trouble. Thanks again for watching.

@charliekrauter5176 Ай бұрын

@@DamonsMetalCasting Good thinking on the investment casting. Haven't done much of that, but that aspect has always made me nervous. I think all of us don't give enough attention to lower body protection. I have a cheap leather apron, but it is warm and have "forgotten" to wear it more than once.

@callmesuperman36 Ай бұрын

Love your dialog and videos!!

@DamonsMetalCasting Ай бұрын

Thanks man much appreciated!

@ma-kuimono Ай бұрын

Hello from Japan. It looks very beautiful when taken out of the sand mold. After all, it's no good if you don't have a proper 3D printer mold. So it will be helpful.😆

@DamonsMetalCasting Ай бұрын

Hey thanks for watching. You are the first I have known about from Japan that has watched my video. Yup you are right about the pattern, "Garbage in garbage out" so its always good to have a proper pattern like you said.

@HawkWorley Ай бұрын

Those turned out fantastic!

@DamonsMetalCasting Ай бұрын

Thank you. I saw you were monetized lately that has to make you feel on top of the world. Congrats. I am still trying to work on mine almost there.

@bulldaagg Ай бұрын

love it lol

@DamonsMetalCasting Ай бұрын

Thanks much appreciated!

@BruceRobinson-tz8cj Ай бұрын

I'm really impressed with the quality of the final cast. I guess that spotting putty must be a contributory factor, however what is spotting putty? Thanks in advance.

@DamonsMetalCasting Ай бұрын

Thanks! The "Bondo Glazing and Spot Putty" helps with filling in the ridges of the 3d print. Just primer can do it as well but the spot putty can go on a little quicker and thicker. Its also easy to sand and doesn't bind up the sand paper so much. How smooth you can get the pattern is how the surface will turn out. Alot of people who make their accessories out of 3d prints for cosplay do this.

@briancurtis6022 Ай бұрын

Very nice work! I've never quite understood how to cast something with a 3-D hollow center--like a shotglass or bottle, for example. I understand making two sides, but how do you place sand to keep the center hollow?

@DamonsMetalCasting Ай бұрын

I have not yet tried any core work to make a casting hollow or have a void. If you look up "sodium silicate core" on youtube you will run across videos that demonstrate what you are looking for. Usually, I have seen people utilize a pattern that includes an area to lay a premade sand core in before the 2 part mold is closed up for casting. If the part is very complicated it might require investment casting. Thank you for watching my video!

@JohnDoe-ny1wp Ай бұрын

Very nice work. I have been doing casting for a few years now. Lately, I've noticed that the quality of crucibles has declined. What brand do you use?

@DamonsMetalCasting Ай бұрын

I only have had to repurchase 1 crucible (the one that came with the furnace cracked). The current crucible I am running is from Amazon and listed as "MakGrand 6.9KG Clay Graphite Crucibles, Melting Casting Metal, Withstand The High Temperature 1800℃(3272°F), Refining Aluminum Gold Silver Copper Glass, Casting Tools (6.9kg)" I have only fired that a few times. Currently, I am experimented with preheating my crucible to 450-500F in a toaster oven before I put it in the furnace with a direct flame on it. Also, I am sure you do this too, I return the crucible to the furnace after use to let it slowly cool inside the furnace when I am done.

@ChatterontheWire Ай бұрын

ADHD, what do you mean, just because you'd already sped it up and I upped the speed to 1.75x!

@DamonsMetalCasting Ай бұрын

LOL. Yeah its hard to hold people's attention on KZfaq. My son has some KZfaqrs he watches and they keep people's attention by screaming through the video. I told him that's worse than reading a book in all caps. Thanks for the watch.