Creator C310 THE BEST BMW OBDII Diagnostic Scan Tool

No video

Creator C310 THE BEST BMW OBDII Diagnostic Scan Tool

Рет қаралды 75,266

6 жыл бұрын

MY NEW BUSINESS: bit.ly/2URZuod
Creator C310 (Amazon): amzn.to/2ZT7lrv
Creator C310 (eBay): ebay.to/2jOKTKk
Bluetooth Tool: amzn.to/2G3XkdT
Actron Tool: amzn.to/2IcI3Ju
B800 SRS: amzn.to/2IcuUjE
If you own a car you need to get your own scan tool. The best ones today are under $100, and will serve you for many years. It will pay for itself the first time you use it - who wants to go to a repair shop every time there is a code or fault? This is especially important for BMW and German car owners where diagnostic rates add up fast.
I review the OBD II diagnostic scan tools I've purchased over the years, including the Actron CP9125, B800 SRS tool, VeePeak Mini, and the Creator C310. The creator is my favorite so far as it does everything in one, and is well under $100.
Best of all it works with early OBDII models like the E36, E46, E38, E39, E53, E90, E92 and all of the modern models like the F30, F20, F22, G11, G30 and so on.
My camera: amzn.to/2qEkaDX
Lens setup: amzn.to/2EVv4cD
Music: / andrewapplepie
ONLINE www.bimmerzeit.com
THE GRAM / bimmerzeit
FACEBOOK / bimmerzeit
TWITTER / bimmerzeit
Disclaimer:
Due to factors beyond the control of BIMMERZEIT, we cannot guarantee against improper use or unauthorized modifications of this information. BIMMERZEIT assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. BIMMERZEIT recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of BIMMERZEIT no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not BIMMERZEIT. Video and Content is owned by BIMMERZEIT © 2018

Пікірлер: 180

@BIMMERZEITT 6 жыл бұрын

TOOLS FROM THIS VIDEO: Creator C310 (Amazon): amzn.to/2ZT7lrv Creator C310 (eBay): ebay.to/2jOKTKk Bluetooth Tool: amzn.to/2G3XkdT Actron Tool: amzn.to/2IcI3Ju B800 SRS: amzn.to/2IcuUjE

@honawikeepa5813 6 жыл бұрын

I have a C310 that works fine. I recently got a D Scan cable as well. Cheers from Aotearoa NZ. We have 2 e39's, '99 523i and '98 AC Schnitzer 540i. We also have an '93 S500L W 140.

@marshmello3818 5 жыл бұрын

Hello, will it work on my ‘97 523i Philippine model?

@honawikeepa5813 5 жыл бұрын

I have a Creator 310. Just need to learn how to use it. Thanks for the video. Cheers from New Zealand.

@craigoliveira7916 4 жыл бұрын

What car do you have g? I have an e46 and im wondering if i should get this to sort my airbag light cheers from Auckland

@honawikeepa5813 2 жыл бұрын

@@craigoliveira7916 1998 AC Schnizter 540i Wifes car. Cheers from Turangi brother. I had a 1993 w140 S500L for a few years.

@piggradio1766 4 жыл бұрын

Hi there, great comparison video, it's very helpful and well done. Can you please tell me if you've managed to do a reset for the Oil Service interval with the Creator C310 if you have a moment? Thank you very much!

@fernandogrubits5207 3 жыл бұрын

Excelent information. Creator c310 can be used on Bmw e60 ? Thanks

@Ghryst 5 жыл бұрын

a c310 tutorial would be good.

@TheChrist117 4 жыл бұрын

Hi. I have a Creator C310+ with version v10.9 software. Having visited their website, I downloaded v11.7 in the form of a RAR, which my MacBook unzipped to reveal a .bin file. I can't get beyond this stage in order to update the Creator's software. Do you have any suggestions on how I might proceed? Thanks for any tips you can provide.

@MINIPOTHOLES 4 жыл бұрын

You cannot run a .bin file on Mac. Switch to a windows computer it will work. Or try to find a Mac compatible softwate.

@TheChrist117 4 жыл бұрын

@@MINIPOTHOLES :Thanks Ben. I've tried a couple of Mac unarchivers: Stuffit and a RAR expander from App Store. So far, no success. Next stop - a friends PC.

@cam1495 2 жыл бұрын

Thank yuo my bro that was awesome, Well done on the video.

@pythonflying 3 жыл бұрын

Which area in the 310 displays the catalyst monitor readiness?

@elypie1965 4 жыл бұрын

Brilliant, best video I've seen on scanners, cheers.

@davidgoodall1963 2 жыл бұрын

Hi There, replaced the old OEM battery with aftermarket like for like m how do I register it with the Creator C310+ scanner, am new to scanners & not tech savvy I'm afraid and instruction book only tells the basics

@sandiegodiy9521 3 жыл бұрын

Hi BIMMER ZEIT! I use the C310 on my BMW X5, the software version programmed on this did not detect my X5 or any codes. Luckily the company provides older software versions that can programmed onto the device. The older version doesn't seem to give me the P codes, just the BMW numeric codes. Do you experience this on your X5? Mine is a 2004. Thanks!

@BIMMERZEITT 3 жыл бұрын

Hey! Yeah you don’t want P codes anyway, the BMW codes are more accurate and specific. I have a $20 pocket scan tool if I want P codes... I guess you’d need 2 tools if you need those.

@DaniilVataman 6 жыл бұрын

Great vid! I own a Creator too 👌🏼

@kay19833 5 жыл бұрын

Does creator work with other cars or it's just strictly BMWs? and does it work with newer model bmws F series, 2, 4 series as well?

@silviodinizdes 3 жыл бұрын

I purchase the creator c310 + odbc 16 to 20 pin. But don't have my model in setup, as a say before I have a BMW 318 TDs 1997, e36 diesel. How can I used my creator. His have a 11.9 software version. Thanks for help.

@zoeleila3330 2 жыл бұрын

So what is the use of this device (the best one in the vid) for someone with little knowledge ? Can I program the little screen bit the same way the ocb plug in thing does? etc

@youngjohn3842 6 жыл бұрын

Great video. Thank! I have a Veepeak and it's cheap but can give pretty much information.

@bronoboy6017 2 жыл бұрын

Mine is V12 version and I can't find o2 voltage

@technik333 5 жыл бұрын

The dreaded DSC light came on today on my E39, plug into a generic scan tool - it reveals an error code "68 DSC steering angle sensor internal". Does this cool Creator C310 initialise and reset the steering angle sensor and hopefully clear the code? I just wanted to confirm the sensor has gone bad prior to replacing it.

@waydemorris1451 5 жыл бұрын

Its a sensor, all it does is sense. No initialising, no resetting. The c310 will clear the code in the ecu memory, if the code comes back after this then the sensor is bad, or the sensor is doing its job and something actually is faulty

@technik333 5 жыл бұрын

@@waydemorris1451 www.bimmerforums.com/forum/showthread.php?1360533-how-to-erase-DSC-light

@whichdoctor4858 2 жыл бұрын

Hi, will it cycle the abs and recalibrate the steering angle sensor? Thanks!

@dazski6607 2 жыл бұрын

I need something to scan a BMW 120i M Sport (2010, convertible model). I've got an amber engine management light on currently. Any suggestions on the best tool?

@agustino6190 5 жыл бұрын

Hi, I have a BMW Classic 3' E36 320i year 12/1997 with ABS and DSC lights on...would this connect with my car and tell me what the problem is? Which one? Thank you very much

@jakobstengard3672 4 жыл бұрын

I have this car and this tool is unable to connect to the abs.

@steliyans4340 3 жыл бұрын

Is this capable of showing live adaptations like inpa software using a pc and cable on earlier bmw cars

@stevescanlon1543 3 жыл бұрын

Great video. Thanks very much. Can you confirm that this scanner will work on a 2017 BMW 535i F10 Msport More specifically will it allow me to turn off the Auto stop/Start Function? Many thanks Steve

@BIMMERZEITT 3 жыл бұрын

Thanks Steve. I think it will work for most things on your 2017 model, however that function might need to be changed with a more capable software to code the car. If you own a PC laptop you will want to look into a cable/cd of BMW ISTA

@regieboix2 3 жыл бұрын

hi mate, will this tool scan a 2001 bmw e39 touring 525d?. i have a problem with my rear air suspension, i have a dash warning light on for the self levelling rear suspension, i changed both rear air bags as they were old anyway, i then changed the suspensions compressor valve block as when i put it under water it had a tiny air leak, i also changed 1 rear level sensor as the arm was broken- but after all that i still have the suspension self levelling warning light on the dash!!!....do you know, will this scanner scan rear air suspension on a 2001 e39 touring 525d ?. do u know if it will turn off the dash warning light??. will the scan tool re calibrate the rear air suspension or read only, any help/advise apppreciated-many thx dave in cold uk....

@Andrew4181975 2 жыл бұрын

Im trying to find a scanner that works with my older bmws with the 20 pin adapter under the hood ,as well as, my 2003 M3 for general maintenance and such ,but esp Airbag and all other modules scanning and resetting codes. With the 20 pin adapter will this scan tool (Creator C310) work with my 1991 325i,1993 525i,1994 325i that all have the old pre OBD systems? It will most likely work with my 2003 M3 ,I assume.

@BIMMERZEITT 2 жыл бұрын

Try this stomp test for the older stuff first: kzfaq.info/get/bejne/eZqEZrRy07eleKc.html I don’t recall if this one has the 20 pin adapter with it unfortunately.

@imjopz 5 жыл бұрын

What is the best scanner i have 2004 e46 325xi wagon? Thanks

@sergiomz21 4 жыл бұрын

Hello quick question can the c310 clear transfer case adaptations?

@wilsonross6593 3 жыл бұрын

Hi I have one for my r55 how do you find the coolant temperature

@johnhaydu4719 4 жыл бұрын

I just bought Creator C310 the screen is blank just white screen. Do I have to download the software I'm confused.

@johnhaydu4719 4 жыл бұрын

I have BMW 328i 2008 it should work for this car too. Do I have return it and get another one.

@BIMMERZEITT 4 жыл бұрын

JOHN HAYDU John I use this on my 328i and 335i as well. Make sure the connector is plugged in all the way, put your key in and push the start button (with your foot OFF the brake) so the ignition is on but the car is off. It should boot up. If not, it’s possible you just received a bad scan tool. It could happen. Return and reorder

@jesuscalvo850 3 жыл бұрын

You can read the dpf values in real time ?

@miccamonnakgosi5493 2 жыл бұрын

Can this Bmw scan tool erases gearbox light and to reset EWS/CAS or align them

@BIMMERZEITT 2 жыл бұрын

I don’t think so. Likely need INPA and laptop with cable for that.

@jakobstengard3672 4 жыл бұрын

I have this, and it is unable to connect to the ABS on my E36. Same on my dads car which is a newer model. Maybe its a sign the ABS box is just broke. But impossible to know 100% what is going on.

@BIMMERZEITT 4 жыл бұрын

Jakob Stengård hi, you need a round port adapter for the early e36. What model and year is your dads car? This scan tool may not be best for early model cars

@stevet8607 4 жыл бұрын

Can this scanner register and Code battery , I have a scanner a only allows me to register the battery but I can't change the ah on it , I bought a new battery 95 ah old battery was 90 ah , it won't let me change that , this will?

@ryanach3596 2 жыл бұрын

Will this work for transmission codes on 98 e36? the website pics say e46 and then the description says e36 a little confused

@tomjackson1927 Жыл бұрын

C310+ update softwares?

@steliyans4340 3 жыл бұрын

Will this work for earlier bmw e39 1997

@AlienWorkshopXD 3 жыл бұрын

i bought one of the creator but it only gives me codes like 7D 0B 01 OA... No p codes??

@gail6904 3 жыл бұрын

Hello can u please help. I bought this but am new at using it..I have a CODE CD99..what does that mean? also, i have 3 CAS module codes CAS AOBE, CAS AOBF, AND CAS AOCO. And another CODE says CDA6 electrical fuel pump..does it mean the Fuel PUMP or Fuel MODULE or relay is bad?? HOPE U CAN HELP ..any and all info appreciated..thanks

@daniellavoie9662 4 жыл бұрын

Great video. Do you think this will work with my 2015 550i? Based another youtube recommendation, I purchased a TopDon Plus and it came back with "no fault codes found" when my CEL came on. I had to go to the dealer to get the codes read - for $200 bucks!! I should've done more research because I've been hearing that BMWs don't work well with Generic code readers. Thoughts?

@BIMMERZEITT 4 жыл бұрын

Daniel Lavoie hey Daniel, a generic obdii reader for $20-30 will pull engine trouble codes on your bmw. But you want something like this to be able to see all of the deeper stuff going on like abs, transmission, stored codes, freeze frame data, airbag and safety systems. I have not tried this on anything newer than 2008 so I would say buy from Amazon and try it. If it doesn’t work out amazon will back you for a free return.

@philippugsley2052 6 жыл бұрын

What scan tool would be recommended for older BMW's? We recently purchased a 1998 BMW Z3 Roadster. Considering the dated technology and advancements in vehicle computer control and sensing units, which scanner would you recommend with capabilities to read and reset basically all of the vehicle codes we may come across?

@honawikeepa5813 5 жыл бұрын

I use a Creator on my wife's '98 540i and daughters 523i. it works great.

@Abdelrahman.dafalla Жыл бұрын

@@honawikeepa5813 Doe cheap OBD2 ELM327 works ?

@hrmthermalimage 3 жыл бұрын

this was a great video thank you

@hrmthermalimage 3 жыл бұрын

i updated the software of my creator c100 from software V4.6 to V6.1 and it seems to be that the newer version is not working as the old one did, it just reads no stop ad no user commands and it never read from the obd2 but read from the round 20 pin plug in the engine compartment. i am thinking that i may have messed up in upgrading the software it use to work on my 2010 x3 from OBD2, but on my 2000 Z3 it worked on the 20 pins only.

@ajaniscott607 4 жыл бұрын

I have an E38 2001 BMW. Can the C310 tool clear an airbag light, can it also tell you which of the four-wheel speed sensor is bad. If not can you tell me what OBD2 tool will do that? Thanks

@BIMMERZEITT 4 жыл бұрын

Ajani Scott yes it will do both of those things!

@jasa198 4 жыл бұрын

@@BIMMERZEITT I have purchased the scanner as the dreaded 3 lights (Abs,red handbrake and Asc) have come on my E46 4 cylinder engine. The code reader will not give me a code instead just says error message.

@MadeinSA658 3 жыл бұрын

Great Video Thanks! Has anyone tried this tool on a E90 320D 2005 model? (C310)

@tonynikon 4 жыл бұрын

Before I buy, I want to make sure I have the correct one. My car is a 2013 BMW X3 28i. My engine sometimes stops by itself after stopping at a stoplight. I took the car to the BMW dealership and they charged me $425...but the problem persists.

@BIMMERZEITT 4 жыл бұрын

Antonio what was the trouble code they found for your car? You may have recourse if the issue was not resolved, I would bring back to the dealer and speak to the supervisor of the service advisors.

@tonynikon 4 жыл бұрын

@@BIMMERZEITT Well, They told me that my car have back the a "weak battery", so they change it for over $400. The problem came back again after a long drive 1 1/2 months later. If I put my cellphone or GPS on the USB connector, by the end of the drive, if I stop at any stop sign, the car shuts down and turn on again when I press the gas pedal. The problem is that the car starts weakly and shuts down completely in the middle of the intersection. I have to put the car on parking mode and press the ignition again. I'm not taking my car back to the BMW dealer because I think it was a rip-off back then.

@BIMMERZEITT 4 жыл бұрын

Antonio L. Rivera it sounds legitimate that the battery was weak and was a good place to start considering your x3 is going on 7 years old (assuming battery is also that age). Is your service engine soon light illuminated on the dashboard? If not a scan may turn up shadow codes related to your issue

@catalyst_yt1472 4 жыл бұрын

Vanos??

@tonynikon 4 жыл бұрын

@@mikeymagic117 I know that the car is designed to shut down when you stop the car at a stop sign or intersection to avoid unnecessary idle and gas waste. The problem is that if I use a GPS or cellphone on a charger, it seams to drain the battery after a longer drive. The problem is that I after I turn the engine again by pressing the gas pedal and start to move, by the middle of an intersection the car shuts down itself. I have to put the car on parking and start the engine again while other cars behind me sound the horn on me. I'm afraid to be hit by another car from behind or if somebody don't stop at a red light while I'm on my right of way...you know the rest. How do I found the camshaft sensor that you mentioned?

@Rob-lj3kf Жыл бұрын

Very good.

@Madjokerx1 5 жыл бұрын

Greetings, Can we re-adapt batteries with this tool? Register new batteries for the IBS(Intelligent Battery Sensor) module? Best Regards, Lehel

@Madjokerx1 5 жыл бұрын

Meanwhile, from the amazon url linked here: "Can you register an after market battery using this piece of equipment? Bmw says you need to register new adter market batteries to get optimim life Answer: Sorry, it cannot support this function" (the seller answered this)

@marksmith1003 3 жыл бұрын

Hello my Good Man, thanks for the reviews and at the risk of being redundant can you confirm that the C310 will clear the SRS light on an E46? I keep finding conflicting information. What about the C110? Thanks

@BIMMERZEITT 3 жыл бұрын

Yes I know the c310 does

@larryjohnson8168 2 жыл бұрын

Does it read on board monitors?

@marksmith1003 2 жыл бұрын

@@larryjohnson8168 what do you mean by on board monitors?

@marksmith1003 2 жыл бұрын

@@larryjohnson8168 it is an onboard diagnostic scanner so I don’t know what you are asking

@larryjohnson8168 2 жыл бұрын

@@marksmith1003 you know the monitors that say if they're ready for a smog check

@eloiajohnson8981 3 жыл бұрын

I got the C310+ for my 95 bmw 740 and it will not communicate with the car

@rustygrigg 2 жыл бұрын

Can the creator 310 be used on other vehicles besides the BMW,s?

@tomjackson1927 Жыл бұрын

Minis

@frankiegarza3002 5 жыл бұрын

I need help. Do I absolutely have to have an H series battery and my 528i 2001 sport or can I put another battery that's brand new or does it have to be an H series I've had one of these tools sitting in my room along with the spare set of struts new smog pump ECR valve new air conditioning front unit new halos better on the car and I have the stock lights so just a bunch of parts I got a set of rims for it but wanted to keep the BBS sanction BMW wheels on. can anybody help?

@MrDyblie 5 жыл бұрын

Great video!

@danielsantiago5248 4 жыл бұрын

I just bought it hopefully work with 2015 BMW 3s Thank you

@BIMMERZEITT 4 жыл бұрын

Daniel, please report back and let us know if it is working with the 2015 model

@danielsantiago5248 4 жыл бұрын

@@BIMMERZEITT yes 2015 BMW 328 I x drive 3 series

@danielsantiago5248 4 жыл бұрын

I will let you know. I wll get it next Monday

@danielsantiago5248 4 жыл бұрын

I just got the Creator C310 today 5/22/20 and it worked 100% Thanks for the video. Now I don't see the sign anymore.

@kulandaivelsundararaj8985 4 жыл бұрын

My BMW is 2004 525i e60. Will this work on this vehicle? I have the airbag warning light.

@BIMMERZEITT 4 жыл бұрын

sundar raj yes it will

@franciscolozano4236 4 жыл бұрын

Will this scanner tell me if I have a faulty vanos solenoid?

@BIMMERZEITT 4 жыл бұрын

Francisco Lozano yep

@moodondie 5 жыл бұрын

Will this scanner identify the location of a bad speed sensor? A generic scanner is pulling a 0500 speed sensor A but doesn't give the location of the failed sensor.

@lcagee 2 жыл бұрын

I was able to pull up live data with the last scanner. Gave me speed of all speed sensors.

@silviodinizdes 4 жыл бұрын

Bimmer i don't no if you can help me but the information about this product si confuse. I have a bmw e36 diesel 1997 this creator c310+ "+" cable obd > 20 pin will work im my car? Because in some sites say yes and others no. I read the manual, talk in e36 but is not especified about diesel. If you can help me i appreciate. Thanks

@BIMMERZEITT 4 жыл бұрын

Sílvio Diniz yes this will work, it is obd-ii however you may have one of those round ports under the hood for other systems since it’s an early model.

@silviodinizdes 4 жыл бұрын

@@BIMMERZEITT Yes my car have a round port "20 pin" and they are diesel. In many places, include a SZcreator don't present your compatible with my car. Then i will purchase one creator 310+ and adapter cable odb-ii to 20 pin. Thanks a lot to fast answer.

@samking4179 6 жыл бұрын

3:20...plenty of free apps as well if you are just looking to see some error codes and then clear them.

@djraisd 5 жыл бұрын

what about airbag?

@ValeevRamil78 6 жыл бұрын

Thanks!

@karamurad5531 4 жыл бұрын

Would this read an bmw e39 530d 2001

@BIMMERZEITT 4 жыл бұрын

kara murad yes

@karamurad5531 4 жыл бұрын

@@BIMMERZEITT because I tryd reading with other tools and it did not read so was thinking of buying one of these thanks

@MrRussell521 4 жыл бұрын

Will this work for a BMW 2003 e46 coupe m54

@BIMMERZEITT 4 жыл бұрын

Charles Russell yes it will

@robertcullerton959 4 жыл бұрын

Question: Does the Creator C310 read the specific wheel speed sensor which is not functioning?

@BIMMERZEITT 4 жыл бұрын

Robert Cullerton yes it should. It’s quite good for $55-65. Each corner will show a different code.

@robertcullerton959 4 жыл бұрын

@@BIMMERZEITT thx

@larryjohnson8168 2 жыл бұрын

I’m having a problem with reading live stream data for wheel speed sensors over 10kmph is that normal for this scanner?

@jequitygroup4108 4 жыл бұрын

Do you still recommend this scan tool in 2020? Or is it something better out there now?

@BIMMERZEITT 4 жыл бұрын

J Equity Group yes I do, I am still using mine! Can’t beat it for the price!

@jequitygroup4108 4 жыл бұрын

@@BIMMERZEITT thanks

@yolredgiants 4 жыл бұрын

what version of the scanner you use in this video?

@BIMMERZEITT 4 жыл бұрын

M Haniff link to it in the description

@danmc2678 5 жыл бұрын

Can the C310 do an adaptive reset for the transfer case fluid change on an X3? If not, is there a tool that can do it for around $50?

@smokedoutog6398 5 ай бұрын

Hi did you ever find a tool that could reset or re-calibrate the transfer case for your bmw? If so which one and how much did it cost?

@danmc2678 5 ай бұрын

@smokedoutog6398 Nope, just had a BMW shop do it. They actually said it wasn't necessary. I sold the X3 a few years ago and got a Subaru. Much happier. The X3 was breaking something once a month.

@Anthony23ao 5 жыл бұрын

Can you use this if you have a Tune installed?

@BIMMERZEITT 5 жыл бұрын

It should still communicate yes

@serdarcaglayan9791 4 жыл бұрын

When you erase a code, does that fix the issue or does it just remove the code?

@BIMMERZEITT 4 жыл бұрын

Serdar Caglayan the code is there to let you know what to repair or where to begin diagnosis. If you simply delete the code without performing the repair, the code will likely come right back sometimes instantly, sometimes within 5, 20, 50 or 100 miles.

@serdarcaglayan9791 4 жыл бұрын

BIMMER ZEIT thank you! Great channel 👏

@carlosorellana200 3 жыл бұрын

Can this scan tool reset ews error or sync?

@BIMMERZEITT 3 жыл бұрын

I don't believe it can. You will need ISTA or INPA with an OBDII cable + PC laptop. Something like this: ebay.us/MeMeW7

@jameslatimer1432 5 жыл бұрын

Hello bro I just BOUGHT one if I need any advise is it ok to give you a shout james

@BIMMERZEITT 5 жыл бұрын

James Latimer 100% hit me up

@joshg7411 4 жыл бұрын

come on man... the link for the C310 tool bring you to the page for the C110 tool. I mistakenly ordered this one and it wont even read the transmission on me e46. waste of $50

@BIMMERZEITT 4 жыл бұрын

amazon sellers change the catalog all the time, can't keep up with all of the links across 100's of videos. I will update this. thanks for letting me know.

@romeoaveria5900 3 жыл бұрын

I got the c310+ after I watched you. Is there a way to find out the meaning of the codes that we get? I got a 01 airbag, driver, stage 1 but I don't know what it meant. Any help would be appreciated. am a big fan. Thanks.

@jtaylor4027 2 жыл бұрын

Google

@KeepinUpWithKi 4 жыл бұрын

Does this work for a 09 bmw 328i?

@BIMMERZEITT 4 жыл бұрын

Kiara J yes

@kalamatacity 5 жыл бұрын

hello .can u confirm that it works for E83?

@BIMMERZEITT 5 жыл бұрын

panos k yes it should

@kalamatacity 5 жыл бұрын

@@BIMMERZEITT thank u

@wilzedens8676 5 жыл бұрын

Hello Bimmer Ziet, Will the creator c310 work properly on my '97 e39 540i by chance?

@BIMMERZEITT 5 жыл бұрын

Wilz Edens yes it should... you have the OBD-ii port under the driver side dashboard correct?

@wilzedens8676 5 жыл бұрын

@@BIMMERZEITT yes sir, ive been using a cheap $20 unbranded & multi-purpose OBD2 (ebay) for awhile. A I want is for the tool to give me / send me in the correct way to fix/repair ( & maybe reset a few issues).

@BIMMERZEITT 5 жыл бұрын

Wilz Edens the c310 will give you wayyyy more info. Def pick one up!

@wilzedens8676 5 жыл бұрын

@@BIMMERZEITT even if my '97 is an early 540i? I don't want to toss my money away of it does not work. Also thank you for responding as quickly as you have Bimmer Zeit.

@BIMMERZEITT 5 жыл бұрын

Wilz Edens yeah order on amazon any issue return it for free

@charlesrivers3977 3 жыл бұрын

Are the scanners able to reset the valvetronic actuator?

@gail6904 4 жыл бұрын

DOES IT SCAN THE BMW MODULES AND LET U REPROGRAM THEM? LIKE FOOTWELL MODULE, BODY MODULE ECU? thanks please email

@BIMMERZEITT 4 жыл бұрын

gail yes

@gail6904 3 жыл бұрын

@@BIMMERZEITT can u please answer my codes question above? thanks so much..

@mindanelson5388 3 жыл бұрын

Will this work on my 2008 Bmw 328i?

@BIMMERZEITT 3 жыл бұрын

Yes!

@mindanelson5388 3 жыл бұрын

@@BIMMERZEITT Thanks.

@CarlosSolis-wd3gx 6 жыл бұрын

Need to replace my abs module. Does any one know if this tool, can recode the new abs module to my car.

@BIMMERZEITT 6 жыл бұрын

hey Carlos, this will not code it to your car. I would recommend having your ABS module rebuilt instead of replacement. Rebuild your current module to avoid the need to code a new unit, see the rebuild here: ebay.to/2mjIKYG

@CarlosSolis-wd3gx 6 жыл бұрын

@@BIMMERZEITT thanks for the reply. But that listing is up to 2003. I got a 2007, i havnt found any one who does rebuilt service. For my 530i. I need a tool to reprogram a replacement, i think i need to recalibrate the steering wheel sensor. Need to name of the tool, im dieing to get my hands on a decent priced unit. Do you know of any ?

@robertklein526 4 жыл бұрын

Will this be a good reader to use for non-BMW ?

@BIMMERZEITT 4 жыл бұрын

I believe this is for BMW only. I will try it on my Audi tomorrow and report back here!

@bogdananghel9480 6 жыл бұрын

I have the C310. But i dont use it anymore, Carly app does everything, it's faster, you can code stuff. It's 10 times better. And it costs 50$ + K-D CAN cable 15$.

@BIMMERZEITT 6 жыл бұрын

I have heard of it, and INPA, but we have apple computers so I'd need to spend at least $2-300 on a windows laptop as well

@bogdananghel9480 6 жыл бұрын

Carly app runs on android or iOS. i strongly recommend to try it, it's awesome!

@josemario1606 6 жыл бұрын

Problem with Carly is that you have to buy the Carly Bluetooth scanner, then you have to purchase de anually subscription for the app, ot's no longer a "1-time pay".

@bogdananghel9480 6 жыл бұрын

Jose Mario Jiménez Alfaro you buy the app once, there is no anually subscription. And i use it with a 10$ K-Dcan cable, not the original bluetooth adapter, and it work perfect.

@MotogiantTL 5 жыл бұрын

@@bogdananghel9480 How do you use the k-can with the carly app? How do you connect to your device?

@12ctb 6 жыл бұрын

Does the Creator 310+ diagnosis things like faulty control arm, bushings, tie rod, sway bar, etc??

@BIMMERZEITT 6 жыл бұрын

there are no sensors associated with those parts so no scan tool will diagnose those things. Suspension failures are usually inspected visually, not with a computer

@12ctb 6 жыл бұрын

Thanks for you quick response! Visually, I know that I need those parts but I'm new to using OBD II so I wasn't sure about all the functions.

@12ctb 6 жыл бұрын

And their user manual is not that descriptive!

@Tanaka7070 5 жыл бұрын

Bought Creator C310 but unable to use it because the menu is Chinese language.

@BIMMERZEITT 5 жыл бұрын

Tanaka7070 interesting I haven’t heard of that before. Can you change it over to English in the settings? Maybe use google translate for help?

@Ghryst 5 жыл бұрын

maybe this should help - try updating to an english version of the same software version you have tutorial here : blog.cardiagtool.co.uk/bmw-creator-c100-v3-8-c110-v4-3-c310-v5-5-download-and-update/

@lcagee 2 жыл бұрын

You can learn Chinese in 4000 hours of study. That would probably be cheaper than going to dealer.

@achow617 6 жыл бұрын

Is there any scan tool or code tool (dunno what those call) that can let me switch my E39 key to unlock all 4 doors at one click on the key fob instead of double click? Do I have to go to dealer?