Cub Cadet Trans Not Working? Check This..

Рет қаралды 21,686

Жыл бұрын

amzn.to/3TGvco0 Plastic Replacement Bracket
amzn.to/3TIaHXX RZT Drive Belt
amzn.to/3cJCgzA Trans. Center Section Left
amzn.to/3BduGXj Trans. Center section Right
In this video I show you a something to look for if your transmission is not working on a Cub Cadet Z force S with the steering wheel.
Help support Doublewide6 Repairs LLC by sponsoring his Patreon Account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.

Пікірлер: 49

@doublewide6 Жыл бұрын

amzn.to/3TGvco0 Plastic Replacement Bracket amzn.to/3TIaHXX RZT Drive Belt amzn.to/3cJCgzA Trans. Center Section Left amzn.to/3BduGXj Trans. Center section Right

@robertbaysinger1309 Жыл бұрын

Nice job as usual! Always amazes me the lack of care people show their equipment.

@doublewide6 Жыл бұрын

You and me both!

@Big_Johns Жыл бұрын

Nice work Bob, lots wrong but it came to the hands of the right guy. 👍🏼👊🏼

@doublewide6 Жыл бұрын

That's a good way to look at it.

@Big_Johns Жыл бұрын

Yes sir 👍🏼

@jiggs49us Жыл бұрын

I like your lift table. Mowers are not the easiest thing to work on - glad you got it fixed up. It will make someone a good little mower and the steering wheel models really hold the hills and slopes compared to the sticks.

@doublewide6 Жыл бұрын

Thanks 👍

@petefroud5308 Жыл бұрын

Nice work Bob.

@Turningwrenches85 Жыл бұрын

Very nice pick up of that cab cadet after that repair it's a solid machine you got there

@willloy8901 Жыл бұрын

Very nice work, and tidy profit should be had upon the sale! What hydraulic oil did you use to replace the old oil?

@J3rbski 9 ай бұрын

I just bought an old exmark and the steering is very slow to engage and whiny. There's a bunch of slop in the steering where minor adjustments on the levers don't seem to be recognized and when I push forward more it finally recognizes and jerks forward. What would cause this? Does not appear to have any leaks and fluid is at the right level. Tracking is way off as well but should be a separate issue. Any insight is appreciated. Thanks!

@butler386 Жыл бұрын

Hmm I don't think I have ever seen a steering wheel on one of these. Fixing the transmission seems like a big project to me. You are one talented man for sure. Thanks for the videos.

@doublewide6 Жыл бұрын

No problem keep on watching and don't forget to comment! much apppreciated.

@rustyrepairs2565 Жыл бұрын

Good work on that machine. Thanks for sharing!!

@doublewide6 Жыл бұрын

Thanks for watching!

@Maximus43968 Жыл бұрын

Well you might break even after you figure all the fustration into it lol. Good fixes for sure testing the old skill box. Worst case if no body a cover for you Adams Small Engine in Greenwich Oh has so many used parts and very fair priced they ship to. Great video as always.

@harveystephens6115 Жыл бұрын

Nice fix

@philliphall5198 Жыл бұрын

Sounds good and will cut grass Well done 👍

@guyina4x499 Жыл бұрын

Nice fix dw6.

@markellis9297 Жыл бұрын

Hey Bob, I have been watching your videos for a few years now and enjoy them very much. I have a question that I hope you can answer, I have watched your zero turn transmission vids many times over before i attempted this chore (like the one where you sanded and honed down the surfaces of the trans center, motor and pump assemblies). Anyhow I have a Cub Cadet rtx-s with the steering wheel and I'mhaving left side trans problems ( i sanded and honed the pump and motor and center assmebly) and there was very minimal groves but sanded since I had the trans out, After reinstalling trans,and purging trans. The left side is still acting up, both sides seem very strong, but when driving the left side will kind of lock up sometimes completely and sometimes just like brakes are on it and moves slowly. This happens sometimes going in a straight line and sometimes while turning, it doesn't do on a regular bases. This can happen in 20 feet or at 100 feet with no rhyme no reason.Ihope you have an answer for me of what them problem may be, because other than that I about to remove trans again and start the process again. The only thing that I can think of is the center section and motor were had to get in and may the center section might have gotten scratched. Any way looking for advice. Thanks again Mark

@henrymurawskibigdogrepair Жыл бұрын

Nicely done Bob

@doublewide6 Жыл бұрын

Thanks Henry.

@CraigArndt Жыл бұрын

$200 bucks, nice. I'm the same way, go in the house, grab something to eat and sometimes a lightbulb goes off and I'll drop what I'm eating and get back out to the garage.

@obadiah7771 Жыл бұрын

Awesome video as usual!!

@doublewide6 Жыл бұрын

You're the best!

@themowerman Жыл бұрын

Yo yo where you been friend.. good to see you are on the way to getting it driving again.. yeah sometimes you just have to walk away for a while..

@doublewide6 Жыл бұрын

Took a break for a while. Nothing really interesting to film. Thanks for noticing. Talk to you soon.

@billlovett4256 Жыл бұрын

Thanks for the video...what brand of lift table is that? And do you like it? Hello from Ottawa, Canada

@doublewide6 Жыл бұрын

Handy brand I would rate it an 8-10. Does the job for me.

@ohiofarmer5918 Жыл бұрын

I am very interested in what the parts cost and how many chargeable hours it would have cost one of your customers. For a contrast, I just bought a 314 Wheel Horse that is identical to the 400 series machine because of the heavy Kohler. Absolutely like new with just a few scratches on the decals. The deck is a bit worn, but still serviceable as they are made of decent steel. I have been buying them for a while and now is a low in the market because people are struggling with high fuel and food prices. Auto trans on old Wheel Horses are commercial grade hydraulic motors and are readily available in the uses parts market. Congratulations to you on having the talent to put it all back to a functional machine. Way above my patience and ability to do so

@doublewide6 Жыл бұрын

As far as transaxle, I advise customers to buy a new one about $1000 installed. If I would rebuild for a customer, it would be $300 in parts and 5-6 hours labor. It would end up around $800 for a rebuilt one.

@nashguy207 Жыл бұрын

700 Hours is not a high hour machine. That one looks like its been road hard and put up wet. Glad to see you got it running and cutting. Good job buddy!!

@doublewide6 Жыл бұрын

Thanks 👍

@kenhilson786 Жыл бұрын

a briggs 33 would have used up 2 cams by 700 hours.

@rickbroerman9267 Жыл бұрын

I have never seen one with a steering wheel like that... that is really cool. R U going to keep it??

@doublewide6 Жыл бұрын

No it's for sale as soon as I get the engine cover.

@mike.4277 Жыл бұрын

Great video, but you called it a tractor lol. I have a 2003 cub cadet tractor. It looks and run like brand new.

@louissparks2496 Жыл бұрын

Wow, your grass looks terrible. What is it, wintertime up there already, or is it a drought?

@doublewide6 Жыл бұрын

drought bad here.

@johnmilner7603 Жыл бұрын

There’s barely any grass left.

@mikespain8655 Жыл бұрын

Personally I don't like these steering wheel zero turns. It had some issues and you fixed them all. Still some good profit in it. Sell it.

@doublewide6 Жыл бұрын

I like the steering wheels because they sell for more and more people are looking for them.

@robertmailhos8159 Жыл бұрын

It was rode hard and put up wet 😞👎

@doublewide6 Жыл бұрын

sure was!

@robertmailhos8159 Жыл бұрын

@@doublewide6 well at least you can get it back in running condition again 👍

@ldr9146 Жыл бұрын

Isn't that typical for a Kawasaki engine to break their engine cover? I'm sure you didn't loose money your labor is free.

@mikespain8655 Жыл бұрын

You spend hours and hours getting a machine ready and right to sell, have the correct tools, and gain the needed experience. Then tell me your labor is "free."

@doublewide6 Жыл бұрын

A lawn chair fell on the engine in a shed. Not a normal problem for Kawi