Did that with a new tube ant compressed tire but just as the tire started to seat the stem valve ripped out of the tube. That was a wasted 37 dollars?? I guess I will buy a second tube as there seems to be know other choices. Thanks for the video it will help on my second try

It has helped, thank you 👍

Why would you not cut out the rust Before welding on new plate? Now you have a nice new piece of metal welded over old rust that will continue to rust.

Now thats a trick mate

That guy wouldn't have had to tell me it was leaking oil, I would of found it when I I checked it out before I paid. 😏

I have an engine just like that does almost the same thing at 30 pounds of PSI the maybe almost 40 but it runs fires 2 or 3 times then stops.

How/Where exactly did you add the Oil⁉️

Excellent! Just inherited one of these. It runs fine and this is great info for future reference. These self propelled models get all clogged up with grass and dirt under the front belt housing and need to be kept clean too.

I have a bypass seal leaking. Is it possible to remove and replace the bypass seal without draining the fluid and removing the transmission? It looks like I have enough room to pull the bypass shaft and remove and replace the seal.

Any update on the scooter is it still running

Saved me tons of money. Thank you sir!

So i did this to mine. i mean it was prolly less damaged than yours. But i did all mine to 1000 grit. Added a tab of grease on that lil key along with the bearings and the pistons so they would stay in place upon assembly. Installed with fresh 20w50. Attempted to purge the system (yes i have leaky external seal on top where the oullry is) but. The thing should still pull better than it is. ITS NOW WORSE! I WAS EXPERIENCING OVERHEATING AFTER ABOUT A HOUR OF MOWING. NOW IT SEEMS TO BE FOING SAME STUPID BS WITHIN 5 MINUTES OF STARTUP. I EVEN USED A WHOLE BOTTLE OF LUCAS

What area you service

I still have mine ever since it came out

On these Carbs u can pull the spacers out of the air box base then slide them over the carb bolts. This allows you to bolt the carb back down without the air box on so you can adjust it while on the machine running.

I took out the sensor one side is red and the other side is white does this mean I need to replace the sensor if so where do I buy it thanks John Billington

That's a great idea. I didn't know what to do with mine too until now

I got one yesterday. Looking forward to using it on just over an acre. Almost got a Craftsman/this one was less money after discounts and more financing,,,12 instead of 6 months 0%. I think I'll be glad I got this. Went from 48 Simplicity to this big 54. Good review btw.

Thanks for the clear and well paced video. A safety reminder is that the starting capacitor can be charged up and waiting to give you a good zapp. It may not kill you but the shock can jerk your body to hit something you'd rather not be hitting. You're wearing rubber gloves, so you're good.

I have had the same exact thing happing to me on this mower

Do u still have this pressure washer? Are u willing to sell the detergent tank only if not damaged. If so for how much. Clean force 1800

This is exactly what’s happening to mine..

My governor came off when putting it back together. What do I hook it to?? Help 😊

What should the amp draw be?

For anyone wanting to know what size wrench to get the electronic needle off the bottom of the bowl it’s a 13mm

Well done buddy. Most helpful. Greatly appreciated. Thanks for making effort.

Nice

Good job 👍🏻

Thanks for this. I had a stuck valve. $95 to replace (for an old grill on its last legs); a full one-quarter the cost of decent new grill. It never would have occurred to me, but heating that puppy up freed it up. The valve is good as new (but, of course, the rusted/oxidized/stripped/broken screws are the challenge now).

Ha. I know this video is old but it's to the point and will solve my problem. I've got two Honda GCV 160's that have the same problem. Thanks for the video and the ever crucial part #.

I just tested another clutch pulley and its looking good no chewed wires just needs cleaned up and put up for if someone may need it i don't but I'll clean it and save it for someone else

FANTASTIC VIDEO. I have a "little" seepage between the case and case cover. Do you think it is possible to drain the oil and remove the case cover to reseal it without removing the entire transaxle?

I have the exact same washer. Now I have water dripping from the soap dispenser any suggestions on how to fix this.

At what point is the pulley too rusty to use? I just replaced a clutch where the pulley was so rusty it had a hole rusted through it.

Seems like with the key on... it would keep spinning the starter even after the tractor cranks up. Shouldn't the starter stop spinning once the tractor cranks? But if you turn the key off, it turns off the tractor?

And what if you do all of those steps and it still is not priming out of the emulsion tube?

I'm in the process of making a 9.5" bacon press out of 3/8 diamond plate. My goal is to heat it on one of the stove burners while i pre heat the cast skillet and it'll cook both sides at the same time. Should bring cooking time way down. I got a handle for a wood stove off Amazon for $7. Just need to soak it in vinegar to derust the diamond side and weld on the handle and season it. I don't think I've ever been so excited to cook bacon. It should work great

I have a 2006 Z44 cub cadet. I was mowing when the blades stopped turning. Got a new battery and when I pull the lever the blades turn slow.

Wow, thank you. I just learned something. The air compressor is nice. I would like to have that.

I really didn't hear much. Most likely the air fuel mixer is off due to old stale gas

My deck belt keeps coming off

Thanks for doing this video, it's quite useful. On the motor side I ground down the extra casting so I could run straight across the entire face. I used a block of granite for both. Mower runs excellent after resurfacing both transmissions.

Most mowers today have no drain plugs

Have that for 12 years, without blade clutch been good for me.

Those are a pickle. Dang sure best to make sure all the lines are right and carb is good to before putting it back together. Sucks to have to tear all that out multiple times! I know unfortunately! 😂

Used the ratchet strap, worked great until I ended up in the hospital lol 😢 I inflated the tire with the ratchet strap on a little too much.. I then used a 12 inch piece of 15 mil rebar to pop the ratchet release as it was under pressure.. The rebar was then driven a half inch into my hand my palm but it was good because it caused the rebar to rotate, glancing off my forehead and landing about 30 feet away. Yup, Nailed it! 🎉

Awesome. How do you fill it? Do you lift it onto a truck? I imagine it would be extremely heavy to move on and off a truck?

Thanks for this, man. Concise and unpretentious. I hope your name pops up again for the next appliance repair I run into.

Thank you for the video! I have the same mower that had same problem, which I fixed after watching your video.

Now change the rear tires on that mower. Harbor freight shaft don’t fit into wheel center. Had to grind two sides flat the fit into wheels 20x8.