Customer Replaced Spark Plugs And Now It Runs Bad!?

Рет қаралды 485,856

5 жыл бұрын

In this video I have a look a customers Nissan Quest. He recently replaced the valve cover gaskets, spark plugs and cam sensors. After getting it back together it ran like poo! Let's see what went wrong here. -Enjoy!
If an SMA Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE: / southmainauto
CHECK OUT OUR "SMA SWAG" STORE! Go on Teespring and get your very own SMA merch!
teespring.com/stores/the-sma-...
If you don't like Patreon feel free to use the "PayPal Me" link: www.paypal.me/SouthMainAuto
The South Main Auto Amazon Store:
www.amazon.com/shop/southmain...
AES Wave Automotive Diagnostic Tools: www.aeswave.com/cart.php?m=af...
Thank you for all the continuing support!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.

Пікірлер: 2 200

@SouthMainAuto 5 жыл бұрын

Sorry for the 360p, something on YT's end... It was uploaded in 1080 60fps. Sometimes this takes a while for them to render it.

@MechShark 5 жыл бұрын

All is forgiven

@ILikeMetricMusic 5 жыл бұрын

The worse mistake I made was ending up with “spare parts” after I changed something in the engine bay 😳

@throttlebottle5906 5 жыл бұрын

South Main Potato :)) worse part, I didn't even notice, watching in smaller window, too many things going at once

@glynwatkins9968 5 жыл бұрын

Any one in the UK also? Hiya Eric

@toysareforboys1 5 жыл бұрын

Generally it's best to wait until it finishes processing before clicking "publish" :)

@andrewamador2214 5 жыл бұрын

Had a foreman who preached "the only person who doesn't make mistakes is the person who doesn't do anything". Too true!

@spiralnapkin 3 жыл бұрын

🙌 that's an amazing quote.

@Paul1958R 5 жыл бұрын

1972 Im 14. Changing the points on older sisters 1969 Plymouth Belvedere slant six. Drop points screw down distributor. Get new screw and install. Start engine. Runs ok. Dad goes out hours later to use the car and crank no start. Screw lodged in advance mechanism which locked the dist and sheared the nylon dist gear. Had to be towed to repair shop. After that I bought one of those spring loaded screw holders. 46 years later I still have that tool. And 46 years later I still remember that Dad didnt get angry. Lost him in 2016 at age 94 and I so miss him. SMA#1 God bless Paul

@navvet4518 4 жыл бұрын

Great story. He shaking his finger at you right now. I’m headed to see my dad for probably the last time in two weeks.

@pfsantos007 4 жыл бұрын

He didn't want to spoil it. You had good intentions and everyone screws up now and then, especially while learning.

@PRO4XKEV 4 жыл бұрын

My father taught me how to work on cars also.. still too this day I am a good mechanic with auto and motorcycle, small gas engines., and miss my father also, he passed in 1986 age 57.8 years.I am now 58 and enjoy working on my own cars and tinkering around.

@thecloneguyz 4 жыл бұрын

Wait till we get a solar flare and it wipes out 300 million cars and you're going to wish you still had a points ignition system sitting in your garage

@quilmesdave 4 жыл бұрын

My Dad taught me everything, about working on cars. He left me in 2016 age 91. Everyday I think of him. Greatest teacher i could have in life and in profession!!

@garywaisner7393 3 жыл бұрын

Like the fact you encourage DIY. And that you don't gripe any complain and belittle when someone makes a mistake and asks for help. Great videos.

@ShellShock794 3 жыл бұрын

It's pretty refreshing. I saw some video of a mechanic on here that was fixing something else and saw a brand new oil filter and said "Aftermarket oil filter..." and you could almost *hear* his eyes roll. What kind of mechanic thinks less of a person for changing their own oil????

@paulsolovyovsky1702 3 жыл бұрын

@@ShellShock794 funny part is that the lube place all use aftermarket oil filters and they are Fram or worse

@simonpickering3609 4 жыл бұрын

"Read your job sheet" the boss was so pleased i had removed a Scania engine in under the time, it was just a shame it was supposed to be another truck across the yard !!

@Spelter 3 жыл бұрын

Omg 🤣🤣🤣

@cgsound 3 жыл бұрын

OUCH!!!

@spelunkerd 5 жыл бұрын

Your customer sounds like a viewer, one of us. This kind of error could happen to anybody, explaining why the pro is so careful to leave a bread crumb trail to find his way home.

@ckm-mkc 5 жыл бұрын

Many pros have made similar mistakes. The difference is that you have to get it right before giving it back to the customer...

@MrJasonAlderman 5 жыл бұрын

If he can do it, I can too!

@russellhltn1396 5 жыл бұрын

@@ckm-mkc I've had techs call me up with a problem and I tell them exactly what wire they got wrong. How? I've already made that mistake.

@bobonlinenet 5 жыл бұрын

i can make a laundry list of mistakes i've made with my 98 cavalier. headlights, to tires, to oil, to coolant. they should teach basic car repairs in drivers ed.

@PayNoTax-GetNoVote 5 жыл бұрын

@@bobonlinenet - they use to.

@TheFirstStater 5 жыл бұрын

Heated a piston with propane torch to put in the wrist pin, which was in ice water. Set the propane torch down, grabbed the piston, bent over to put in the pin and set my hair on fire. Didn't realize I was on fire until I smelled a horrible odor. No injury but a memorable moment is screw ups.

@throttlebottle5906 5 жыл бұрын

lmao! I set torch down once on top a water heater doing plumbing, in tight basement, it was still lit and aimed directly onto the floor joist, which happily and quickly ignited. I was a kid and had water there to quickly put it out. danged kids doing plumbing lol

@ckm-mkc 5 жыл бұрын

This is why I have no hair....

@waynegouin939 5 жыл бұрын

A guy i worked with called me a risk taker. I said damn right i am. TIP- if your scared to take a little risk once in awhile, stay home in bed, im sure the boss will understand. That guy NEVER got ANYTHING done. He ALWAYS relied on someone else.

@billburkart9087 5 жыл бұрын

I was under my house trying to hook 115 volt line to run to my shed. There was 2 lines the other one was 220 running to my baseboard heat. I turned the power off and laying on my back pulled the 115 line down to cut. I then looked away to get my side cutters. When I looked back up I did not realize that the 115 volt had returned to it's location and I cut the wire closest to my face. When I got my vision back my side cutters were glowing bright red with sparks coming off of them. I still have those side cutters and now I can also use them to strip wires because of the round spot burned into the center.

@andrewcairnes2491 5 жыл бұрын

Wayne Gouin

@Mytwistedvoices 4 жыл бұрын

The first time I replaced my plugs, it ran like poop. I drove it to a mechanic. He put the wires in the correct order and didn’t want any money. I bought him lunch. Never happened again.

@stalincat2457 4 жыл бұрын

I didn't connect the spark plug caps properly and started to look for air intake leaks using a flammable aerosol. Never happened again!

@ihateeverything9887 4 жыл бұрын

Mytwistedvoices what I learned in mechanic school is, that the 10 seconds it takes to masking tape and label the plug wires can save you hours and a headache.

@Mytwistedvoices 4 жыл бұрын

I was 16 before any mechanic schooling or KZfaq. Call it a learning experience. I have a BS in Avionics, AS in Aviation maintenance (licensed aircraft maintenance technician, I am a pilot and I have a degree in electronic engineering. Spark plug wires are easy now.

@Mytwistedvoices 4 жыл бұрын

@tim coker Love the old Chargers, I'm rebuilding my 1978 Honda CB750 Supersport. I have a video somewhere on KZfaq about it. Just replaced all four rubber brake lines on my 2012 Caravan, one blew and lost all the fluid. The ABS was fine so normal bleeding and the van is perfect!

@keithwittman4741 4 жыл бұрын

I would switch two wires to prevent my brother from taking my 79 Camaro, without my permission.

@fangbeer 5 жыл бұрын

Spent a half hour trying to pound off a rusty old rear brake rotor until I realized the emergency brake was set...

@snoopdogie187 5 жыл бұрын

You're lucky. I spent more than that pounding on a brake rotor, which didn't even have a working parking brake. I had to cut the rotors off. You know its a bad day when the sledge hammer isn't strong enough.

@VortechBand 5 жыл бұрын

@@snoopdogie187 Time for the good old hammer drill!

@snoopdogie187 5 жыл бұрын

I went with the angle grinder and a cut off wheel. They came off fairly quickly after that.

@dellstudio10 5 жыл бұрын

I did that just last month on my F-150. Luckily I realized it was on after it didn't budge after 5 or 6 whacks. It's also the second time I've done it. Guess I'll never learn haha!

@watchmewrench9462 4 жыл бұрын

I did this and brought out the torch to heat up the drums, thinking they were rusted on. Only after half a can of lubricant and a lot of hammering did I realized the parking brake was set. Oh well!

@kennedy796 5 жыл бұрын

I made this mistake before. Now i just do it one plug at a time. Keeps the confusion down and nothing gets mixed

@brianmcpherson2906 5 жыл бұрын

kennedy796 I have 8 clothes pins numbered 1-8 with a sharpie. Stick em on before pulling anything apart and I don't have to worry about putting it back together.

@VortechBand 5 жыл бұрын

That's how I learned to do it. At worst, the wires are unlabeled, so if you take them off, there's very little indication where they should go. Do them one by one, and it's impossible to make a mistake :)

@8avexp 5 жыл бұрын

My father, who was an engineer, gave me this tip once: when taking something apart for the first time, write down each step as you go along.

@johnnyramirez9082 5 жыл бұрын

Brian McPherson that’s a dang good idea. I’m stealing that one

@Arieeeee 5 жыл бұрын

It's a rite of passage

@Hoodie-xj2iv 5 жыл бұрын

“Hoping to administer the classic reach around.” Lol 😆

@gregeconomeier1476 5 жыл бұрын

I thought you did that on a date??

@soloban81 5 жыл бұрын

Usually have to pay extra for that.

@RedfishCarolina 5 жыл бұрын

At least he had the decency to do a reach around

@MrRodnick1955 5 жыл бұрын

Hey guys she is someone’s daughter keep it GP.

@Hoodie-xj2iv 5 жыл бұрын

Rodney Farmer lol he said that in the video bro, not coming from me, that why there are quotes.

@g0dl355 5 жыл бұрын

I'm a shade tree mechanic at best, and even that may be a stretch. I try to help friends and family with car issues when I can. Had a friend ask me to do a brake job. I did it, no problem, but when she was driving it one of the calipers seized. Turns out I wasn't as thorough as I should have been when I tightened everything down and one of the bolts actually worked its way loose and the caliper jammed itself against the wheel. She had it towed to a shop close to her and when I called to pay for my mistake the owner told me "No charge, I put a bolt back in it, I've made the same mistake" That made me feel a little better, but I still cringe when I think about how I screwed that up. Thanks for a great channel, I learn something new every time I watch your videos.

@smitty1952 3 жыл бұрын

You are a good man Eric! No gloating, no condescending, etc. Not a surprise to those of us that consider ourselves loyal followers of you and SMA. Thanks again!

@drp457 5 жыл бұрын

After 5 hours of rebuilding a transmission, giving it to the installer and finding that important snap ring on the side of my bench! Boy was he pissed.

@kennleeds4342 Жыл бұрын

That's what is called integrity.

@richardclemmens9410 5 жыл бұрын

What I love about watching you is your awesome attitude. Thanks for your videos

@MrJeffcoley1 4 жыл бұрын

I figured that’s what he did - got the wires mixed up. An old man I knew told me about buying a 32 Ford hot rod back in the 1950’s. The owner was selling it because it ran like shit and he couldn’t figure out the problem. It was a dog: Not missing, but no power. My buddy took it down to the local garage where the owner let him use the bay to work on his own car to do a tune up. It had a dual distributor Mallory ignition and he pulled all the plug wires without marking them. Then he had to ask for help so the owner got out the shop manual and they figured out the firing order and got it put back together. Suddenly the car was a screamer. It would lay rubber all the way down the block. The guy who sold it had it firing out of order. Just like your customer.

@brianszymanski2971 3 жыл бұрын

I've always replaced spark plugs one at a time no confusion about the wiring mix ups.

@michaelb.7800 3 жыл бұрын

Some of these newer wiring harnesses the force you to remove all of it at the same time like all three coils just because of how short they are things like that but they're still just enough to plug into each other luckily I've had enough experience and training wisdom doing this for 18 years now day in and day out I've luckily never made that mistake yet

@kyngreese 3 жыл бұрын

@@michaelb.7800 I get my paint pen and get to numbering them 😂

@SGTUSMCVET269 3 жыл бұрын

You can still mix them up. Trust me lol

@BrandenAllen 3 жыл бұрын

Same, after messing up the first time I ever did plugs. Never again.

@mitchd949 3 жыл бұрын

Nice vid. I like how you thought about things: 1) you read the customer info provided, 2) you thought about what to check, 3) you used a diagnostic tool to assess the running problem one cylinder at a time, 4) you determined what things (ignition wiring) are supposed to look like, 5) you examined how the car is actually setup. You deduced that connectors were incorrectly placed and rectified the situation. Also, excellent DIY advice: before taking anything apart TAKE A LOT OF PICTURES! Too bad every car mechanic isn't like you. I hope the customers beat a path to your door!

@EM-df6mo 4 жыл бұрын

Props to the owner for sharing his misfortune and letting others learn. After all none of us are immune from error. I like how Eric handles these teaching moments and doesn’t belittle people. Great job Eric, as always.

@GunfighterWyo 5 жыл бұрын

I saw Miss Marie keeping an eye on you. Her famous smile is great! Never has to say anything, just give you that smile!

@BWDuty605 3 жыл бұрын

Taking lots of pictures before tearing into anything is some of the best advice possible! After realizing how much it helps with drum brakes I started doing it any time I get into something I'm not familiar with. I also try to disconnect only one plug at a time if possible.

@kurtzimmerman1637 5 жыл бұрын

If you work on stuff long enough, you will screw something up. That's just how it works. 🔧🔩😆

@vacayooper4728 5 жыл бұрын

Almost every "weird" problem I've ever had regarding repairing automobiles was a result of my mistake.

@rickharper1497 5 жыл бұрын

If you don't make mistakes your not doing anything

@kurtzimmerman1637 5 жыл бұрын

@Scotty Kilmer your a great mechanic and influence on my thinking . Thank you for all the information you provide. 🔧🔩😆 thank you.

@deziking 5 жыл бұрын

This guy prob had few more beers and got tired and lazy, yea end of story. Seems like.

@jameskane319 5 жыл бұрын

Did my own plugs... Replaced with "triple Platinum", thinking they'd be better. Still ran like poo, so I did coil, wires, etc.. No change. Bought a vehicle in the meantime, finally brought it to a pro. Replaced with OEM plugs... That'll be 250 bucks, please. My $20k spark plugs story...

@LMacNeill 5 жыл бұрын

When changing spark plugs, do 'em one at a time -- completely change one and plug its coil back in before removing the next one. :-)

@DonaldDump2024 4 жыл бұрын

Yep. That’s what I do. No mixups. Mixed wires can cause big problems and do serious damage. Take pictures, draw diagrams, do it systematically.

@teeboo123 4 жыл бұрын

Another idea would be to write on the connector with a sharpie or use color coded zip ties.

@thomasflynn5366 4 жыл бұрын

I was going to say the same thing. Can't screw it up that way.

@joedonohoe108 3 жыл бұрын

That's the way you should do it, if you don't know the firing order.

@Backyardmech1 3 жыл бұрын

Especially on an engine you don’t know very well. I know my cylinder numbers and distributor on my old truck is numbered. If it was any other vehicle your method can’t be messed up.

@dougkubash8673 3 жыл бұрын

I give the guy tons of credit for changing the plugs! It looks a fun job.

@antony580 4 жыл бұрын

Nice video Eric! The owner made a mistake but you're always very respectful of customers and I really appreciate that.

@s2hjt 5 жыл бұрын

Changing the oil with a hangover. Forgot to put the sump plug in. The oil surrounded my boots until I slipped over and landed on my butt.

@bobl78 5 жыл бұрын

changed manual transmission oil AT NIGHT , 100% dark night, with a torch light.. filler hole on top of transmission through engine compartment ( front drive) .. used a funnel to stick in the fill hole and poured 3 Liters of oil into it... until i heared a strange sound reminding me of some liquid pouring on a surface... the funnel was not in the hole , it was next to it.. 3 liters of transmission oil allover my transmission, drive axle, subframe and of course the drive way... it took me weeks and countless power washes to get the oil off my car and several bottles of oil stain remover to "repair" the rive way... an insane mess....my dad was very pissed of because of that huge stain. I looked like somebody drained an oil tanke And of course could not drive to work the next morning because I had no more tranny oil

@Aschmorr 5 жыл бұрын

Johnny Blue that’s why you gotta change the oil WHEN you’re drinking😉

@chillyourself5208 4 жыл бұрын

Did this while baked on my DRZ400, its got 3 drain plug locations, and 1 magnetic filter. I left 1 loose.... 50oz car wash on the ground cleaned it up nicely.

@loveurself1197 4 жыл бұрын

O ur butt plug?

@russdavis1960 5 жыл бұрын

Like MeMa used to say, "If you don't make mistakes, you ain't doin' anything".

@ufartface 3 жыл бұрын

or learning

@ivenhoho 3 жыл бұрын

In my younger days, a particularly fastidious customer brought in a new Pontiac for an oil change. I drained the oil and affixed a new filter. I then pumped new oil from a 55 gal drum into a large metal pitcher with a flexible spout, which we used instead of separate qt cans. As I began to orient the pitcher over the brand-new sparkling clean engine, I lost my balance and poured the entire pitcher over the engine and engine bay as the customer was standing there inspecting my work. Actually, it looked kind of pretty, glistening in the light.

@hellshade2 4 жыл бұрын

i was an auto mechanic for 32 years and have seen all kinds of weird and crazy customer issues. one time a woman brought in a caprice classic,305ci engine with 4 barrel carb. the car was only a few years old at the time and it was running rough and smoking a ton out the exhaust. turns out the engine was literally full of oil up to the valve cover. the woman thought changing the oil meant putting another 5 quarts in never realizing that old oil needed to be drained out and filter replaced. so we drained it and put the proper amount of oil back in and swapped the plugs. it smoked for about 15 minutes or so afterwards but cleared and was running just fine after that

@scottraymond558 5 жыл бұрын

My buddy was trying to drill out bolts..called me..he ruined a bunch of bits..I showed up and was watching..turned out he was using the drill in reverse..

@Cheepchipsable 5 жыл бұрын

Reminds me of the occasional fella who changes his wheel, thinking to himself..."Man these are tight..." Of course he is turning the wrong way and breaking the studs.

@eileenheitman4351 5 жыл бұрын

I’m a carpenter/contractor. I hired a young kid...18..at his fathers request( one of my customers) . He thought it would be good for his son to experience some real world stuff. I laid out a bunch of locations on some lumber denoting where to drill holes. I told him to drill the holes and bring the lumber around back where I was working. This was an addition to a residence. I turned him loose and I went around back to work. Time passes...no lumber. I walk back to the horses in the front....kid is sweating bullets. Yea, same thing....running drill bit backwards. I canned him. I think he was happy to go. I assume he is now a lawyer/accountant/I.T. guy. Something with soft hands. Different strokes. Dave Heitman Semper Fidelis

@eileenheitman4351 5 жыл бұрын

Cheepchipsable I had a blowout while driving my Dads 61 Plymouth Fury back in 1967. I was 16 on my way home from my job at the Safeway grocery store. I was doing 110 when it happened, but I digress. Stopped, jacked up car,.....”damn, these lugs are tight”. I twisted one off. Shit. Tried another. Twisted it off. Shit!!!! Tried righty loosey on the next and it came off easily. Chrysler Corp lugs back then were righty tighty on one side of the car and righty loosely on the other side. Learned that the hard way. Dad was pissed. That was 53 years ago. One year later, at age 17 I joined the Marines. I was 17 so my dad had to sign the papers giving permission since I was under 18. He almost set the paper on fire from signing so fast. I think he was glad to see me go. My younger brother then took over the responsibility of driving Dad nuts. My brother succeeded in doing so. He knocked up his girlfriend at age 18. She was 19. They are still married. And very happy. In 1971 my brother ....same brother....drove his new 1971 ‘Cuda 340, 4 speed ...”up a tree”. I was in Vietnam and missed out on the aftermath of that shitstorm. Dave Heitman Semper Fidelis

@mikeford963 4 жыл бұрын

Maybe he thought they were left hand drill bits? Yes, those exist. Snap on has them as bolt removal tools.

@naula7 4 жыл бұрын

LOL! That was a hard brief chuckle..

@tomwise1109 5 жыл бұрын

When I was 15, I rode a little Yamaha DT100 everywhere. One day the bike would Idle and move at low rpm's But as soon as she was opened up , she fell on her face. I limped it to a small shop after I couldn't figure out what was wrong. The mechanic came out after my explanation, Lifted the seat , removed my gloves from the intake of the air filter and said. That'll be 20 bucks.

@istvanmeissler2238 5 жыл бұрын

Tom Wise Was he joking or did you really have to pay?

@misterhat5823 5 жыл бұрын

@@istvanmeissler2238 $20 is fair. Who knows when he'd figured that out. Bet it never happened again though.

@tomwise1109 5 жыл бұрын

Oh he was serious. It was definitely a life lesson.

@dellstudio10 5 жыл бұрын

He's gotta make money where he can haha! I had an old Yamaha timberwolf I was working on but didn't have a new air filter for the test drive (the old one fell apart). So I managed find a larger foam filter I had laying around and attached it to the cage with a couple of zip ties just temporarily for the test drive. It dies about 10 minutes into the ride. I looked to check the usual suspects but everything was fine. Then it dawned on me that the air filter may have got sucked through the carb and sure enough it did. It got pulled all the way through the carb then hung up on the intake valve steam. Pulled that out, went and bought the correct filter then all was well again.

@PayNoTax-GetNoVote 5 жыл бұрын

Had an "meticulous (anal)" buddy who put a plastic bag over the intake to his jet ski for winter storage. Come summer, he couldn't figure out why it wasn't running right....I'm sure you can figure it out from here.

@dianagoodrich7169 5 жыл бұрын

Hello! Once in a while you had said "This must be the most boring video …". It was not. Seeing how the work gets done, mistakes and all, does not make a video boring. When you talk to the camera and let us in on what is going on, that is great. I watched the repair of a stripped spark plug hole [from about 3 years ago]. While we could not see directly what you were doing, your explanations and demonstrations of what was going on were very effective. Seeing the results with the endoscope was a great finish to the process. I thank you for taking the extra time to record the process of repairs you make. Each of your videos tells a story well. I also appreciate your respect of other channels which do a good job so you do not feel you have to do things they demonstrate well. Note -- I knew a gal whose husband likely replaced the spark plugs in her car. He pulled all of the ignition wires without marking where they connected. And he took the ignition wires off of the distributor. You know the result -- the car barely held on running. A friend of hers and mine rearranged the connections to help the car run a little more smoothly. While so whacked as the system was, the change helped her drive the car somewhere to get the order fixed. I have not done real mechanical work on any car. I did replace a radio. I forgot where the fuse was located. I connected through the proper wire line, not remembering it had a fuse on it. [The car was old enough to use cylindrical fuses. And the radio fuse was in an add-on capsule.] When I finished the change the radio did not work. Except for a couple of seconds when the car ran over a bump that reconnected the broken wire in the fuse. I think I finished the fix. Which might not have been needed if only the fuse were changed. [The newer radio was an upgrade. It was all good.]

@deme7063 5 жыл бұрын

my biggest mistake was not spending more time picking the ole man's brain on how to do this stuff before it was too late

@lewisbeshers1946 5 жыл бұрын

Miss Marie. Videobomber extraordinaire! Your cell phone camera is definitely your best friend during reassembly.

@jefffairchild7074 5 жыл бұрын

16 years old, first car, tried to change oil, drained transmission instead. It was a stick shift and very hard to put in gear that day until I figured it out.

@beverlyroemer5161 5 жыл бұрын

Jeff Fairchild oh sh** 😂😂

@elguapo1690 4 жыл бұрын

Lol, did you put another 5 quarts in your engine?

@jasonsaeli75 4 жыл бұрын

Lmao

@benpeterson3373 4 жыл бұрын

I did the same thing. And, filled the engine with a ton of extra oil. Oops.

@jonathonbreneman3799 4 жыл бұрын

I did that in my automatic. Couldn’t even put it in gear. Thankfully no damage was done

@scottpollard3270 5 жыл бұрын

Just rebuilt 1st transmission. Put tcc valve in backwards. Had to drop trans to fix. Runs good now!

@michaelszczys8316 3 жыл бұрын

You always get it right the second time

@burpostockings 4 жыл бұрын

I just ordered new plugs and wires and this video magically popped up in my recommends. Thanks for the anxiety youtube

@projectfamily5802 4 жыл бұрын

Watch what you can do wrong in this vid

@toshayonguard4253 3 жыл бұрын

It’s the Machine building an algorithm on you. 😳😳😳

@toshayonguard4253 3 жыл бұрын

Use colored markers to mark each connector that way when your exhausted putting it back together you can just match the colors. 🤟🏻🤟🏻🤟🏻🇺🇸🇺🇸🇺🇸

@nahuelgalmarini117 3 жыл бұрын

As long as you do one at a time you'll be ok

@fredrickmartin8238 3 жыл бұрын

I just thought about buying spark plugs...

@daveogarf 5 жыл бұрын

YAYYY, Ms. Marie's back! It's FUN to watch her learn; reminds me of my own auto mechanical experience growing up.

@Teribus13 5 жыл бұрын

Sometimes when you're elbow deep in a project, it's easy to miss the obvious. I work in bus garages, and I think most of us have had a situation where we can't get something to work, only for someone else to sort it out in seconds. In a similar train of thought, sometimes it's best to walk away for a bit, then come back with a fresh, clear mind.

@michaelszczys8316 3 жыл бұрын

One of hardest times troubleshooting something was when I changed a motor in a car and it would run but only idle slowly. Any amount of over idle it would not go or quit. After spending like a whole day going over EVERY LAST THING I finally got the notion to try disconnecting the exhaust pipe and it went zoom. Turns out the old engine blew so much oil it plugged up the catalytic converter and sitting made it solid. Now when I was on forums helping troubleshoot other people’s cars one of my favorite questions when it sounded possible was “ have you tried disconnecting your exhaust?”

@Asto508 3 жыл бұрын

The funny thing is that this is universal to any kind of troubleshooting. It's exactly the same for programmers who can't figure out why certain code doesn't behave as it should. Then someone else with a fresh pair of eyes comes along and spots the issue in a matter of seconds after you wasted hours or even days on it. Happens to everyone occasionally. :)

@Lugnut64052 2 жыл бұрын

Yes, and sometimes after an all-day struggle all it takes is for someone to walk by and make some offhand remark about the issue to trigger the inspiration to solve it in a minute or two. Had that happen more than once.

@PaulysAuto 5 жыл бұрын

Great video and it's nice that your customer gave you a good amount of detail regarding his repairs to get some ideas on where to focus. Hope you're staying busy and enjoying the beautiful weather Eric!

@garyd.7294 5 жыл бұрын

Thanks Bud, a good example of why I love my 2000/4.0 Grand Cherokee. One coil pack, one plug.

@jantzenmoore2250 5 жыл бұрын

After years of working my own vehicles, I learned always take pictures, label, and have a few extra 10mm around. Also buying a nice scan tool will help you tremendously.

@klwthe3rd 5 жыл бұрын

Never get tired of the Austin Powers references in Eric O's videos. It runs "smooth". Also playing space invaders with the center console controls were super fun!

@joeblackwell1216 5 жыл бұрын

Thanks for the video Eric! We all find ourselves in trouble from time to time. I once did a front brake job on my 98 Ranger. I failed to realize when I took off the rotors that the inner bearing was inside the rotor. Took it to the machine shop where they turned the rotors. Inner bearings were sitting next to the rotors, but I failed to pick them up. I couldn't figure out why my rotors would not seat properly on the truck... DIY distaster as I towed the truck to the local mechanic. Problem got worse as the ABS sensors were damaged during my failed brake job. Cost me so much more than just paying for a pro brake job. Multiple lessons learned in this one.

@toddzino58 5 жыл бұрын

ERIC: Mr. Customer, you plugged two wires in wrong. Customer: I feel silly.... ERIC: Don’t feel silly! That will be $425. Please pay Mrs. O at the Window. 🤣🤣🤣👍

@JG-xn1kv 5 жыл бұрын

😂🤣😂

@smackdaddy1ful 5 жыл бұрын

you guys think your gods gift to cars....what a bunch of crap!!!

@rideordie3305 5 жыл бұрын

@@smackdaddy1ful When you have to take half the car apart to get to a plug or anything else for that matter. It's not cheap. My tools and time are not free. At least he didn't have to pull the upper intake off.

@trackerrrr 5 жыл бұрын

@@smackdaddy1ful Let us know when you are willing to work for free on our stuff, we'll be happy to come use your services.

@jameskane319 5 жыл бұрын

Still cheaper than my "$20k spark plugs" 😁😁😁😢😢😢

@eileenheitman4351 5 жыл бұрын

These comments are killing me. I haven’t laughed so hard in a long long time. Glad to know I’m not the only idiot out there. Thanks.Dave Heitman. Semper Fidelis

@gary00832 3 жыл бұрын

Don't idiot yourself, you're only an idiot if you keep making the same mistake over and over again

@yyz125 4 жыл бұрын

You have a very modest personality most mechanics would ridicule someone who makes mistakes, your not only a great diagnostic tech, but awesome teacher

@farrelltrosclair9175 3 жыл бұрын

My first oil change on my first car (18 years old). I actually thought I could look inside the valve cover and see the oil level. My buddy never lets me forget that.

@efman2k3 5 жыл бұрын

P/J's = Plugs /jacks ( connectors) Great video. Thanks for posting!

@AntonioClaudioMichael 5 жыл бұрын

Vehicle owner was very informative and that's always nice

@pedlpower 5 жыл бұрын

It's good that the customer told you everything they did. Most will bring the car in and say nothing. Worst is when they take it to a shop that does all the gravy work, doesn't fix the original problem, and then customer brings it to you to fix.

@scottwilde5918 4 жыл бұрын

Almost spit my coffee out when I heard the reach around comment. Too funny. Very good information on the video. Keep 'em coming.

@exmember1607 4 жыл бұрын

If you don’t want to change 1 plug at a time and replace the connector each time, just get some grease pens of different colors and mark each one before you take any out. Then you can just match red and red, green and green, etc

@traceur21 5 жыл бұрын

New Jeep hat! Sometimes we have to move on... keep up the great videos!

@ouch1011 4 жыл бұрын

When I replaced the head gaskets on my 98 Legacy GT, I swapped the 1 and 3 injector connectors. Ran almost perfectly fine except for a slight miss about once every 30 seconds at hot idle. Not enough to even set a code. I drove it that way for a couple years until one of the classes I attended had a case study for a Subaru that very occasionally set misfire codes at idle because someone had swapped the injector connectors....

@robertlee4172 4 жыл бұрын

Bought a new '87 Nissan Stanza, was showing it to a mechanic friend. He suggested getting the shop manual. ($75.00 - a lot of money back in '87) Over the years did many small jobs just following instructions. New plugs, headlights, telescoping antenna, electric window, fuel filter, air filter, heat shield, swap winter tires. Worth it, as it taught me about car maintenance. 10 years in, a leaky valve cover. Again, a minor repair, but in my mind something mysterious and new. Bought the gasket and followed the blow up drawing and instructions. Scraped old gasket, dropped in new one. 45 minutes later and the job was complete, The car ran for another 4 years until the wiring harness started showing signs of wear. All kinds of electrical problems. Sold the car for $500.00 bucks. It still ran but I didn't want to spend the time and money trouble shooting multiple problems.

@kcknitlegt 5 жыл бұрын

Those fricken Nissan Green plugs are a pain in the ass when you have easy access to them, Kudos to the finger dexterity.

@marcuswarren2235 5 жыл бұрын

Doing valve cover gaskets on a Honda Odyssey one time I “completed” the job. Got off from work, went home and woke up in the middle of the night only to realize I didn’t put a gasket on the rear valve cover. Thankfully the customer was out of town and the vehicle hadn’t been picked up yet..

@michaelszczys8316 3 жыл бұрын

Gotta love those ‘ middle of the night realizations ‘ I know I’ve had a few.

@12mak 3 жыл бұрын

How do u even do that? You cant feel the metal on metal when you put it in place? Or when torquring the bolts you didnt feel how solid it was?

@markferrick10 2 жыл бұрын

I always take picture of anything I am about to work on. Saved my butt many times. Fun video, thanks.

@michaelkoncal7622 4 жыл бұрын

Mr O! You are a kind person and I love watching S M A R LLC .

@dankleman4911 5 жыл бұрын

Watching me do DIY is like watching a Benny Hill skit, only in real time, not fast. Needless to say, that's why I drive truck and not turn wrenches, love your videos by the way.

@dtnel 5 жыл бұрын

Ms. Marie hanging out trying to take your job Eric... better watch out! You'll be sitting in the office before you know it.

@MrJeffreywhp 5 жыл бұрын

This has me rolling

@glynwatkins9968 5 жыл бұрын

DIY Failure

@curtisj2165 5 жыл бұрын

Yep, time for Eric to retire anyway😃

@rickb8808 5 жыл бұрын

Maybe that's Eric's plan. Everyone wants to retire sometime.

@darrenroops4756 5 жыл бұрын

Miss Marie is always smiling :)

@atmoore74 5 ай бұрын

This video saved me big time. I did the exact same thing this week on a 2007 Dodge Grand Caravan because I wrongly assumed the cylinder firing order was laid out the same way the the ignition coil pack was labeled. Sure enough I had 1 and 3 switched around. I've been trying to figure out what was wrong for the last 3 days and came across your video. Thanks a bunch I almost gave up and took it to a shop for diagnostics.

@samestep2863 5 жыл бұрын

Thumbs up to you and the family! You make a difference in every video!

@bobapthorpe 5 жыл бұрын

"If I can do it, you can do it" goes for mistakes too :) Seriously though, a camera is a great tool for any kind of diagnosis and repair. It's so easy to forget how something was set up originally and having a photo or video record is a cheap & easy way to save your bacon.

@ryans413 5 жыл бұрын

aclight Internet is handy too google images can help

@JG-xn1kv 5 жыл бұрын

I usually remember to take pictures at the end when it isn't working. Doh!

@chevychase3103 5 жыл бұрын

Yes but back in the day you would have to own a pricey Polaroid!

@jo300hn 5 жыл бұрын

@@chevychase3103 back in the day we drew pictures on the wall

@nickmayo2974 5 жыл бұрын

Agreed, we all make mistakes. I was overhauling a 5 speed Integra transmission for a bad input shaft bearing back in the day and put 5th gear in upside down. The reverse lockout synchro and the distance collar right above turned a nice blue hue and got welded together in short order. It's my favorite paperweight as a reminder.

@AGuyandHisProjects 4 жыл бұрын

Subscribed! Always appreciate your videos for their simplicity, yet, informational at the same time. Easy to follow and watch.

@nathancollins4556 5 жыл бұрын

"We are not exempt from making mistakes, myself included." Truer words have never been said.

@danb316 5 жыл бұрын

holy shit man, you had me at the reach around, but it was the jiggly bit that did me in,

@southjerseysound7340 5 жыл бұрын

My biggest mistake was while doing a fuel pump on a Lincoln inside the tank. At the time we used regular lightbulbs in worklights. Well the service writer came out in the bay and knocked the light off,hitting the open tank igniting EVERYTHING. The fire extinguishers did nothing to control it and by the time the fire Dept got there the car, and half of the garage was on fire. Luckily we got our boxes out and most of the cars but the building was a loss. The only saving grace was the dealership had already started building a new location that was almost finished. But nonetheless I should've covered that tank opening.

@rollinajoint9657 5 жыл бұрын

A accident like this can happen Even in a professional environment. Just takes seconds for it to occur. Lucky that no one was hurt. This Really something left In the hands of a pro. Fuel work in the hands a novice is not a advisable thing. Thanks for your story SouthJerseySound

@southjerseysound7340 5 жыл бұрын

@@rollinajoint9657 So true and it was pretty common for the old work lights to start fires back then. Usually they were small but not this time. There was a reason why even service writers weren't permitted in certain areas of the shop and that was one of them. Technically he wasn't supposed to go inside the yellow zones as they called them and a techs lift was a "yellow zone". After the fire the insurance company put a end to using those lights and we had to use the long fluorescent tubes in a plastic housing and they sucked. But now thanks to guys like Astro tools we've got super bright cordless LEDS that are very safe.

@rollinajoint9657 5 жыл бұрын

SouthJerseySound Indeed. I have seen a few costly blunders. I respect your insight.

@gregorykern9679 3 жыл бұрын

Thanks for a great video. Also, thank you for recording this in the correct horizontal format. It looks great and fills the screen like it should.

@Buc_Stops_Here 5 жыл бұрын

Thanks for sharing, makes me feel better about mistakes I have made. I replaced the valve cover on my old Toyota Cressida in the mid 1990s but I pinched the seal on the cover, so when I started the engine on a test the oil started squirting out. Quickly turned off the engine so no damage, and then had to take everything apart again to replace the engine valve cover seal a second time. So it took twice as long. It was my first experience working on my own car and I have made some minor mistakes since, but I don't do many complicated things.

@rubenp8750 5 жыл бұрын

Was still in high school. Changing the oil at my uncles house who kept a very clean driveway. Did not check to see if the old filter gasket was still in the old filter. Let’s just say that an oil pump can drain an oil pan very fast. Meanwhile my friend is on the ground laughing.

@quicksc1 5 жыл бұрын

I did that with my old ranger, I was 30 though. I left a trail from my driveway all the way down the street. Doh

@sirsweetness8332 5 жыл бұрын

TSP cleans oil off concrete very well and cheap. Happened to my mother-in-law’s car many years ago. Hot oil and 3 qts on nice new concrete. You couldn’t tell after I cleaned it off.

@jl4091 5 жыл бұрын

I once worked on the wrong hole,but it turned out fine over the long haul.

@troyfordguy1345 5 жыл бұрын

When I was rebuilding my Daughters engine in her 1998 Nissan Altima I mixed the Distributor plug with the transmission speed sensor... car wouldn't start and started poking around. The plugs are the SAME color but not the WIRES, after 2 hours of scratching my head I switched the plugs and she fired right up. Great video, even mechanics can make this mistake.

@mjmcomputers 5 жыл бұрын

I often find myself rewinding my videos to see what went where. One of the benefits of videoing everything.

@louarmstrong6128 2 ай бұрын

Or watch a KZfaq video of that repair on your make and model

@joeweaver9913 4 жыл бұрын

Definitely helps to label things or do one at a time to avoid confusion!

@jeremyhoyle2358 5 жыл бұрын

Way back when I was first learning how to work on cars. I put a 250 straight 6 in a 79 Z28. It was all I had. But anyhow after getting the engine in. I didnt have all the wires hooked up and just had to hear it run. So I jumped the starter out the car fired up and was in reverse. It drug me across a field before slamming into my dad's 64 GMC. I had to take the walk of shame limping.

@brianthompson2045 Жыл бұрын

Gives good warning and advice to those of us who have to save money by doing some of these things on our own. Taking pictures before is great advice!!!

@Nic1Moreno 4 жыл бұрын

So very right....wish mechanics in my area would be honest like you

@PineHollowAutoDiagnostics 5 жыл бұрын

Ah the Scanner Danner classic coil switcharoo :)

@Torsee 5 жыл бұрын

Cleaning throttle body fuel injectors. Used a black screw driver to hold butterfly valve wide open (cable jam technique). Sprayed gumout. Reassembled. Started nice clean black painted block of a 350 engine. Found out GM puts a rev limiter on that nice engine. Pegged twice before i could kill her. Realized my mistake. (Camouflaged screwdriver) Surprisingly the engine lived a long happy life.

@brianbrundage3116 5 жыл бұрын

Torsee I heard a story from a friend who test drove his car and forgot to take screwdriver out of choke and he opened it up and it fell through and held it wide open

@guidedpayload 5 жыл бұрын

@@brianbrundage3116 oops

@Torsee 5 жыл бұрын

Yee Haw!

@stevenkushinski6674 4 жыл бұрын

I've done the plug wire cross thing. Yep we all make mistakes. Another great video Eric as always!!!!!

@rebeccadunn3979 2 ай бұрын

Thank you so much!! I just did a tuneup and started it up and it had a misfire!! I’m going to double check my SP wires! Thank you!!

@psdaengr911 5 жыл бұрын

If two similar looking pars can be switched, label them. I keep a set of 6 different color nail polishes (Dollar Store) for that purpose. The 5 minute drying time is worth the wait. Also good for marking things that mechanics you use are supposed to change or move around, like filters and wheels.

@baxrok2. 5 жыл бұрын

DIY'er eats humble pie. At least he made a decent effort to diagnose it himself. Thanks Dr. O!

@raymonddey7403 5 жыл бұрын

I have been doing all the work on my car thanks to this dude. Granted I have a Toyota Corolla , it is nice to have a scanner to find out what's wrong and fix it yourself first. And if you need help... Come here to see doctor o for some info

@onefixitman 3 жыл бұрын

Eric you are always the bomb. Love it. Take it easy on the fella. Everyone makes plenty of mistakes. You are so correct.

@ericbeard7007 3 жыл бұрын

When u was young like 04 I took brakes apart walked to store.... put all back together and couldn't bleed brake. I guess I put the air beeders down instead up. So yeah take pics. This guy up road said 50 theb charged 400 crook... thank God for these channels. Keep it up

@gideon4747 4 жыл бұрын

When I was 16 I changed my spark plugs for the first time and I torqued them down to about 100 foot pounds... the spark plug blew apart on the first crank and I spent a few hours fishing bits of ceramic and metal out of the cylinder with tweezers...

@GadGetHackss 4 жыл бұрын

😖

@americanstreet8704 4 жыл бұрын

100 foot pounds would strip them right out most they would go is about 30

@howardpike6415 4 жыл бұрын

Must have been back in the day when heads were cast iron.

@RJMaker 5 жыл бұрын

HA-HVAC/R Tech.. Service Call... The person who was "in the Know" wasn't there. The person who answered the door didn't think there was a problem with the unit but let me in anyway.... Well as it turns out they were right, I could not find any problem. Just as I was concluding my diag. wrap up, the "In the Know" party arrived and said "I never called anyone".. After looking back at the service order, my complete embarrassment washed over me.. Turns out I 'dyslexia-ed' the house number, DOH wrong house, right street. Thankfully everyone had a good laugh in the end...

@Familyray 5 жыл бұрын

Must have been a looker outside in the flowers made you mix up the numbers, happens a bunch during a long hot summer

@rjhornsby 5 жыл бұрын

years ago (paper map days, no GPS) I was a pizza delivery driver. Turns out there were two streets with the same name, on opposite sides of town. Of course, I went to the wrong one and couldn’t find a matching house number. Finally figured out my mistake and drove back across town to deliver what by now was a semi warm pizza. It had just rained so my customers were outside enjoying a rainbow, so much so that they didn’t mind I was late with their dinner.

@exninja6387 5 жыл бұрын

@Mo Chubby's Music In my city (PHX metro) the street names are the same for the entire latitude, regardless if the street itself stops and starts again. So you can't just say "I live on Oak street" cuz there could be 50 miles and 80 different "Oak" streets, so the number is critical.

@Graham_Langley 5 жыл бұрын

@@rjhornsby Here in the UK there are two towns called Ashford on opposite sides of London. Not a problem these days with SatNav but many years ago I knew an Aussie filling in as a motorcycle delivery driver who found out the hard way.

@Graham_Langley 5 жыл бұрын

Yesterday I came home to find someone sanding the garage door prior to repainting it. Problem was they should been doing my neighbours' one.

@bradskis81 3 жыл бұрын

I remember as a kid my dad working on our Bronco, or something, can't remember exactly... He went inside to get something and I thought I'd help him out by removing all 8 plug wires off the dist cap. He came back out and was none too pleased with my handy work. After a few choice words, and some I didn't know existed, he politely explained cylinder timing and why it's important to do a single cylinder at a time.

@rpierce62 4 жыл бұрын

You are non assuming of people and show respect for FYI folks. Many YT screamers hate us for working on our cars. Again, long time viewer and love a night of unwinding learning from you. Best to you and wifey.. Richard

@sharedknowledge6640 5 жыл бұрын

It’s especially forgivable given the extremely poor access and visibility to the rear bank. I would worry, however, about the cat being damaged from all that raw fuel if it was driven very far as Nissan apparently couldn’t be bothered to kill the injectors on dead cylinders to save the expensive cat.

@jkmacgyver 5 жыл бұрын

fairly common on Tribute/Escape/Mariner 3.0L as well.. will make front cats crumble and clog rear. $$$ been there. Luckily I "cleaned" the rear and no codes as the manifold exceeds value of vehicle w/ 194k

@VDPEFi 5 жыл бұрын

Vw don’t either, my wife killed the cats on her golf driving with a misfire due to a dodgy coil.

@flagmichael 5 жыл бұрын

@@jkmacgyver Could be worse - in the 2003-2005 (IIRC) Nissan V6s the precats were apparently mounted too close to the cylinder, and when the cats started crumbling some of the grit was pulled back into the cylinders, causing horrible wear. A quart of oil with every fill-up is not unheard of.

@sharedknowledge6640 5 жыл бұрын

flagmichael Yet more half baked Nissan/Renault “engineering” and another reason why Nissan is way down in market share.

@nolimitstech8595 4 жыл бұрын

That's why you replace your spark plugs one at a time.

@stephaneaudette6665 3 жыл бұрын

My first time changing plugs i broke one in the head. 😳😳😳😳 I was so nervous but the mechanic repair it so quickly. Thank you guys.

@jameswiseman9377 4 жыл бұрын

Great channel!Love diagnosis’s & mechanic knowledge!

@jameskearney4100 5 жыл бұрын

Did that when I was a teenager. But I figured it out. If it worked before you did work then you got something wrong. Recheck your work.

@akmudslinger01 5 жыл бұрын

Changed the cap, rotor, wires and plugs on a Ford F150 351. At about 35 mph it began popping and backfiring, slowed down below this speed and stopped. Pulled over three times and checked and rechecked wires and firing order, all was correct. Continued driving and problem resumed above 35mph. Finally discovered problem, had loaded a canoe onto the truck's lumber rack, and there was a loose panel in the canoes stern (canoe on backwards, stern towards front of truck) and at 35mph and faster, the wind made the panel flap up and down, smacking the rack and sounding throughout the truck. Lol, had us going for awhile there..........

@uh1c-chiefna996 3 жыл бұрын

Same mistake got me a free car. I knew a guy with an old Valiant that wouldn't run. He said it was mine, just tow it out of his carport. Under the hood it was full of brand new components, carb, coil, battery, choke, ignition harness . . . anything that could be replaced from the parts house. Yep, the distributor was in backwards and a vacuum line was missing. Ten minutes and two dollars gave me a car that ran for a hundred thousand miles. You rock SMA.

@michaelginther6341 5 жыл бұрын

I was changing plugs and wires on a chevy 350 (maybe it was a 305). I used to have a habit of just ripping every thing off and using the book to run the new plug wires. The ring on the top of the distributor had the cylinder numbers on them. So I hooked them all up according to the numbers on the ring. It wouldn't run for shit so we took it to a local shop and they told us that there are two different cylinder sequences for that chevy. The one on the ring was not the correct firing sequence. As you can guess, I don't just rip the plug wires off anymore. I replace them one by one. Thanks for the videos. I enjoy watching them.

@garrettstevensen2467 5 жыл бұрын

Michael Ginther exactly what I was gonna say. Remove one by one.

@michaelginther6341 5 жыл бұрын

@@garrettstevensen2467 Hopefully we never stop learning.