CYLINDER HONING FOR DUMMIES

CYLINDER HONING FOR DUMMIES - 383 Build Pt. 1

Рет қаралды 711

11 ай бұрын

Let's build a 383 for THE BLACK WIDOW!!! Step one - get a free engine... Step two - insect parts... Step three - HOW MUCH IS THIS FREE ENGINE GOING TO COST ME!?!?!?
GODSPEED GARAGE T-SHIRTS and MORE!!!
**Get FREE SHIPPING on orders over $40 using code FREESHIP40 **
GSG MERCH: godspeedgaragemerch.bigcartel...
Copyright GODSPEED Garage, LLC. 2023 All Rights Reserved
*Disclaimer - This video is intended for entertainment only. GODSPEED Garage, LLC, or anyone involved in making this video is not responsible for any damage to person or property that may occur attempting this on your own. You assume all responsibility for your own safety as well as use of your property.

Пікірлер: 18

@Texasknowhow 11 ай бұрын

Good tips for the stone hone. I’ve got a Ford 352 FE block that I was about to rebuild and had to move due to job change 7 years ago. Was freshly machined .030 over from Machine shop. Before I wrapped it up I soaked it down a few times with WD-40…. Almost scared to unwrap and see how it’s survived…. I’m like you, lots of un-finished projects. I’m in the process of another move now. Haha. Hoping this can be our final move and I can get back at all these projects soon. Good to see you on this one, keep ‘em coming. Encouragement for the rest of us. Clay

@GODSPEEDGarage 11 ай бұрын

it never ends... glad to know I'm not alone! thanks for the encouragement! and thanks for watching and subscribing!

@ryanhodges7101 11 ай бұрын

Hey man, I just subscribed. I watched your painted whitewall tire tutorial and it was great! It is the best out there by far. I never would have thought of using the vinyl die as a topcoat and using a heat gun. I’m going to try it out. The follow up video was great too. I was amazed how well they held up. Your truck looks great. I always liked that year of Fleetside. The rear lights look like rockets. I have a ‘95 Cadillac Fleetwood and they don’t make whitewalls in the factory size anymore. Thank you so much!

@GODSPEEDGarage 11 ай бұрын

thanks for subscribing!

@UnconventionalMetal 11 ай бұрын

Very timely video. I’m getting ready to do this to a 4.3 boat engine in a few days.

@GODSPEEDGarage 11 ай бұрын

good luck! hope it works out...

@factoryratgarage 11 ай бұрын

Run it looks fine.

@chevybeaglenox2402 11 ай бұрын

I’ve rebuilt motors that have scoring in cylinders, it’s never caused me any issues. However I’ve never built high performance motors.

@GODSPEEDGarage 11 ай бұрын

thanks! yeah, several others have said mine should be fine... let's just hope it doesn't blow apart going down the drag strip! ha!

@joseortega1114 11 ай бұрын

Use the ball flex hone ball

@joseortega1114 11 ай бұрын

And keep the piston ring organized

@GODSPEEDGarage 11 ай бұрын

oh yeah BIG time... super important since the rings are gapped for each specific cylinder. thanks!

@joseortega1114 11 ай бұрын

Just make sure to measure the piston ring gap clearances

@GODSPEEDGarage 11 ай бұрын

definitely. I will likely go with all new pistons, not just replace the one. new rings, etc, and the machine shop will balance everything. thanks for watching!