No video

Changing trailer wheel bearings

  Рет қаралды 416,111

Dangar Marine

Dangar Marine

Күн бұрын

This video shows how to change the wheel bearings on a boat trailer. This includes removing the wheel, the brakes and then the original races. We then go through how to install the new races and pack the new bearings with grease before putting it all back together. If you have a wobble in your trailer wheels, this is definitely the job you need to be doing.
For outboard repair information, checkout my website: outboard.danga...
If you are enjoying this channel, please consider making a donation to www.paypal.me/... or become a Patreon of Dangar Marine at / dangarmarine
T-shirts and other merchandise available at teespring.com/...
Common items used in these videos are available from my Amazon store at www.amazon.com...
Dangar Marine is proudly sponsored by MarineEngine.com. MarineEngine.com supplies a wide variety of spare parts for many brands of outboard motors. If you are in the US, be sure to check out their online store www.marineengin...
All music available at soundscloud.com...

Пікірлер: 489
@sbweeden
@sbweeden 10 ай бұрын
A trick my uncle showed me was to take a set of old bearing races and grind the outside of them a little on a bench grinder, till they slide in and out of a hub without grabbing. Keep these for helping to seat new races, as you don't have to ever tap them out - they just slide out super easy once the new race is seated.
@vxnova1
@vxnova1 7 жыл бұрын
You say these videos turn out harder than they should do. I am sure the majority of people doing this work also encounter the same issues, Which makes your videos some of the most helpful on the net. Thanks and keep up the good work.
@DangarMarine
@DangarMarine 7 жыл бұрын
Thanks mate, I think it is good to realise that some jobs can be tricky sometimes and it isn't just them. It's always nice to know you aren't struggling alone!
@maryeddy3644
@maryeddy3644 7 жыл бұрын
Your video shows what it's like in the real world where everything isn't new and doesn't just pop right apart. Real problems with real solutions. GREAT JOB - KEEP IT UP!
@DangarMarine
@DangarMarine 7 жыл бұрын
Thanks mate!
@greygonads2
@greygonads2 Жыл бұрын
A few extra tricks, Use a grinder with a cut off wheel to slice through the old races to tap in new ones which makes it easier to remove afterwards. Rotate the hub whilst tightening the nut which may help to align or make both cones parallel, then back off to required preload tension, usually about 2 to 5 newtons. Make sure those pads you use to knock in seal ring are clean so as not to introduce debri into clean grease.
@peterfrancis450
@peterfrancis450 5 жыл бұрын
Great video to encourage the amateurs among us to have a go and not to panic when the going get tough! Thanks for all the details you included.
@antonygreenwood4581
@antonygreenwood4581 4 жыл бұрын
I have to say first class, just spent 4 nights watching all your video posts better than watching tv, there is nothing you cant find an answer for thanks stu very entertaining and informative
@davidlove7825
@davidlove7825 6 жыл бұрын
The other trick if can't get the races out, run a bead of weld along tne races and tney just about fall out. Love your videos. I am a very experienced boat owner but love the great explanations. You are saving a lot of money for your watchers.
@DangarMarine
@DangarMarine 6 жыл бұрын
I have given that a go a few times since I made this video and I was amazed how well it worked. As you say, they practically fall out. :)
@TheAndrewShows
@TheAndrewShows 4 жыл бұрын
There’s no way I’m gonna destroy my hub by welding it , can’t get the race out I’m gonna leave it in there or spend a ton more money destroying it with a bunch of weld
@Blackford86
@Blackford86 5 жыл бұрын
I’m sure someone has already said this before but put the new bearing races in put them in the freezer for about an hour they will slide right in
@scottjohnson9096
@scottjohnson9096 5 жыл бұрын
Great video , here's a trick I've learned from doing wheel bearing races on semis and trailers . Take your welder and put a bead on the race . You'll find it will fall right out as the bead cools it will pull the race looser .
@dougbryer3090
@dougbryer3090 7 жыл бұрын
Well, last year I built up and made kayak trailer and with the help from this video put in new hubs and bearings and made it from New Jersey to Florida, 3000 miles round trip. Well this year I did my big boat trailer. Twin axle that was used in salt water and was never maintained ( I am the second owner). After two years of re-doing the boat, I did the trailer. Went from old rusty drum brakes to stainless discs. New hubs and bearings. Replaced the drop down axles and spindles. Well, last year you mentioned to me something about the "rust gods". I now have some new respect about salt water and what it does to metal. The rust gods made me pay, but in the end they let me finish. Thanks Man !
@DangarMarine
@DangarMarine 7 жыл бұрын
Hey Doug, great to hear you've had great success with your trailer upgrades. Yes, the rust gods are formidable, but they can be defeated! :)
@ronpowell2373
@ronpowell2373 6 жыл бұрын
An old trick for outer bearing races is to put them in the freezer while you take the hub apart and punch out the old outer races . When you go to fit the new races you can also preheat the whole hub before fitting the now frozen new bearing races. If you do this you will often find that the new outer race will almost fall in to the hub and need a very light tap to seat the outer race fully.
@DangarMarine
@DangarMarine 6 жыл бұрын
Hey Ron. Yes! We have a freezer full of Land Rover suspension bushings at the moment waiting to get pressed in. ;)
@colinbartlett2565
@colinbartlett2565 4 жыл бұрын
Top man, it’s good to see that professionals get problems too. Most blokes only show you how smooth the job goes. We all come across problems in life it’s how we get over them that’s important. Cheers mate top channel . Col
@tnth9099
@tnth9099 Жыл бұрын
If you weld a small part of the race it will shrink and come out easy. Love your channel!
@leeroyexcavator9149
@leeroyexcavator9149 11 ай бұрын
Exactly what I was gonna say I have saved myself a lot of trouble by welding a small bead around the races and it will sometimes just shatter and fall out.
@ScubaDiveSydney
@ScubaDiveSydney 7 жыл бұрын
I think this has to be the best DIY video I have ever seen. Great work and thankyou.
@DangarMarine
@DangarMarine 7 жыл бұрын
Thanks mate, glad the video helped you. See you on (or under) the water one day maybe!
@Dan-si8ln
@Dan-si8ln 5 жыл бұрын
Theres something so good about hearing how to do something by an Aussie for an aussie... thanks mate helped me change bearing over Chrissy holidays when everything's shut.
@DangarMarine
@DangarMarine 5 жыл бұрын
Thanks Dan, glad the vid helped you get the job done. :)
@peterbachmann7922
@peterbachmann7922 5 жыл бұрын
Hello Stu, when I do the bearings, I put a very fine grease film, on the back of the bearing race. It makes it easier to replace the bearings at the next service. I also use the copper anti seize grease, on the wheel studs and the bolts that holds the brakes housing.
@trustme7731
@trustme7731 4 жыл бұрын
Threads such as these should never be lubricated. Makes them easier to come loose by themselves and torque specs are for dry threads. Otherwise severe over torquing will happen.
@fstopza
@fstopza 6 жыл бұрын
Great video Stu. What I've found works really well to get a new race in is to use an appropriately sized socket inside the race (just like the bearing carriage would fit in the race) and then a block of wood and a hammer. Much easier than trying to align the old race correctly to get it past the lip and saves you having to tap it out *again*. Granted, sockets aren't designed to take the impact of all those hammer blows, but I haven't had a problem yet and it gives the safety police something to wring their hands over.
@DangarMarine
@DangarMarine 6 жыл бұрын
Yep, that can be a good way to go it you have a socket big enough. Impact sockets are best but I've never broken a socket by hammering on it. Maybe just wear glasses to be on the safe side.
@brentbowler4890
@brentbowler4890 2 жыл бұрын
@@DangarMarine Thanks for posting this, you're my go to for all things to do with my trailer boat. One idea I saw somewhere I liked is cuting a slot in the old race to make it easier to remove after using it to push the new one all the way in, makes it much easier to remove the old one
@Kurtdog63
@Kurtdog63 4 жыл бұрын
The difference between a do it yourself and a seasoned mechanic is the ability to over come obstacles that come with dealing with corroded, frozen, stuck, or worse case- broke off parts, bolts. Many do it your selfers don't have the skill, knowledge, nor the mechanical devices to overcome. Thanks for showing what it takes and the patience you took with the frozen bearing sleave.
@MrCalifornia1234
@MrCalifornia1234 6 жыл бұрын
Thanks so much. I decided to get a new rotor which made the process pretty easy. 10 years dipping the boat trailer in salt water did it in.
@DangarMarine
@DangarMarine 6 жыл бұрын
Yeah, that is often the best way to go for sure. With many cars this day your only choice is to replace the whole hub if the bearings go.
@pateril
@pateril 2 жыл бұрын
Thorough and well demonstrated. I managed to change my bearings today thank you. I was a bit intimidated by the inner races but I followed your tap-tap-tapping method until they loosened. My hub had two round channels running in the same direction as the stub axle which allowed me to get my metal rod snucked in behind the bearing shell. It took a good ten minutes for the first to pop out and only two minutes for the second one. I would've given up earlier had I not been inspired by your video. Brilliant!
@DangarMarine
@DangarMarine 2 жыл бұрын
Thanks mate, glad the video helped you. :)
@QNH1018
@QNH1018 7 жыл бұрын
Great video, thanks heaps. I couldn't get the races past flush and I looked at buckets of US videos but yours was the only one that gave a practical description of how to do it. Thanks again.
@DangarMarine
@DangarMarine 7 жыл бұрын
You're welcome mate, glad the video helped you. :)
@Kapt.Kman007
@Kapt.Kman007 21 күн бұрын
I think you did a great job. I do the bearings and races the same way
@shaenj
@shaenj 5 жыл бұрын
Very interesting to me personally. Every single step you did was just as my father taught me in the early sixties. He was big on treating wheel bearings with respect. We did multiple circuits of Australia towing trailers or vans. I followed in his footsteps as I aged. I can't recall either of us having a hot bearing.
@dsr20631
@dsr20631 7 жыл бұрын
This is a good descriptive video and one to follow for sure. If I could add one tip to other viewers though I suggest giving the old bearing races a quick touch up on the bench grinder to make the diameter a mickey whisker smaller than original size which helps to remove it again once the new one is seated. Keep them in the toolbox for future use.
@DangarMarine
@DangarMarine 7 жыл бұрын
That's a good tip, there are only a couple of sizes so as you say, well worth keeping them once they are made up.
@Neseri2de
@Neseri2de 5 жыл бұрын
@@DangarMarine Ever tried putting the cups in the freezer for an hour before installation, makes them shrink just that little bit.
@turbostyler
@turbostyler 5 жыл бұрын
Neseri2de I chuck them in the freezer the night before and also heat the hub on a little gas stove. super easy to get them in after that.
@jimjezeski4247
@jimjezeski4247 3 жыл бұрын
Very nice job of explaining how to remove/install bearing buddy and remove/install races. Great video for someone looking to do their bearings for the first time.
@DangarMarine
@DangarMarine 3 жыл бұрын
Glad it helped
@bossboyent
@bossboyent 4 жыл бұрын
Just went through all the same hassles and trailer configuration as this. It was a nightmare and I can't believe I didn't see this vid until now! Would have saved me hours. Took me ages to work out I could use the old ring and a piece of timber to smash it in the last few cm
@Colt3854
@Colt3854 4 жыл бұрын
Stu, grind the outer circumference of the old bearing race a few thou. That way it will not stick in the hub and it is a lot easier to remove the old race after the new one is fully seated. Keep the old ones for next time. It is worthwhile drilling a couple of holes in the hub and into the bearing buddies for self tapping metal screws. Prevents them flying off at high speed and causing an injury. Also stops the discount shoppers at the boat ramp parking area from removing the buddies easily.
@jeebus6263
@jeebus6263 3 жыл бұрын
How would you line them up, it wouldn't be cool to have new wholes each time
@mrdiyguy123
@mrdiyguy123 Жыл бұрын
You have a very strong ability to tell a good story. Thanks for the tips.
@RealSuburbanCowboy
@RealSuburbanCowboy 3 жыл бұрын
Showing people how to do this (with all the difficulties they WILL run into) is awesome. If you take the old race and grind/sand a tiny bit off the outer diameter of the old race, you will be able to easily remove it. No punch needed. GREAT VIDEO!
@Chris-ei7iz
@Chris-ei7iz Жыл бұрын
You should do a video on how to add a brake system onto a boat trailer for people that don't already have brakes on a trailer but would like to put brakes on it
@rickyrandyrich
@rickyrandyrich 3 жыл бұрын
Best hub and bearing install video I have ever seen. Great work Mate !!!.
@DangarMarine
@DangarMarine 3 жыл бұрын
Thanks 👍
@georgeharrington6210
@georgeharrington6210 2 жыл бұрын
Way more thorough then most of the other guys. Nice job!
@DangarMarine
@DangarMarine 2 жыл бұрын
Thanks George.
@martyhing7421
@martyhing7421 7 жыл бұрын
Thanks Stu! It's actually great to see a DIY video where the pro has trouble. Makes me feel better when things don't go to plan. It's also really helpful to get some ideas on what you can try when things get stuck.
@DangarMarine
@DangarMarine 7 жыл бұрын
You're welcome Marty. Things always go wrong! Editing the hardship out it just hiding what it really takes to get most jobs done.
@MercurialTorpor
@MercurialTorpor 5 жыл бұрын
Love your videos! Yeah, boat trailer wheel bearing replacement is my least favourite job but as you stress, critically important. I actually had a wheel fall off due to catastrophic bearing failure (completely shattered probably due to a corroded spacer). Fortunately it happened after launching the boat and driving back up the ramp - it's shocking and scary to see a wheel rolling back into the water from the rear view mirror. It's a tandem trailer so I still had 3 wheels to get the trailer parked and start the horrendous task of replacement in the car park at Berowra ramp in 40 degree heat. Fortunately it was one of the lazy hubs and not a brake hub. It happened shortly after I'd bought the boat & trailer and it taught me to be ultra attentive to all of the rolling stock. In fact it was so shocking that I rebuilt the trailer after that - including 4 new springs. The conjured image of one and a half tons of shattered fibreglass strewn across a road was too much for me. A few things I've learned to do to make the job easier is: 1) Use grease everywhere, like on the wheel stubs and nuts - nothing worse than frozen nuts when you are trying to remove a wheel. Yes, I do realise the double entendre! And no, they don't work loose as one might intuitively expect. 2) Grease the new races to facilitate easier pressing into the hub and it also makes removal much easier 3) When using an old race to drive the new race into the hub, just a single cut straight through the ring with an angle grinder makes removal unbelievably easy. Keep that cut race as a tool forever. 4) A cold chisel with the tip ground to a radius along the back of the blade so it sits nicely on the protruding edge of the race to be removed makes removal of stubborn races much easier. It's no longer much use as a cold chisel but very useful for race removal.
@Soul_Survivor2
@Soul_Survivor2 3 жыл бұрын
Love your steps to do the change but definitely would use the old brake pad to tap in the seal as it can make old dust/rust fall in
@michaelkane2868
@michaelkane2868 6 жыл бұрын
Mate I’m 46 and never had to change a bearing in my life, I just bought a tinny and the trailer is a bit sad so after watching your vid I decided to have a crack at the bearings!!!! Piece of piss! Thanks mate keep up the good work!
@DangarMarine
@DangarMarine 6 жыл бұрын
Thanks Michael, glad to hear the job went well. :)
@jeebus6263
@jeebus6263 3 жыл бұрын
Piece of piss? Yall gotta learn to cuss!
@peterwalker7869
@peterwalker7869 4 жыл бұрын
I was shown a trick to removing the outer races. Fire up your welder on a fairly high amp setting. Weld a bead around the middle of the race. As the weld cools it will contract the race is it will latterly fall out. Saves a lot of frustrations.
@byromscustomwoodworks
@byromscustomwoodworks 7 жыл бұрын
Great video. I just had to do this on a boat trailer I bought a month ago. Discovered the bearings were bad as I was backing in to the driveway when a wheel fell off. Just glad it wasn't going down the highway
@DangarMarine
@DangarMarine 7 жыл бұрын
The driveway is the best place to have that happen!
@calumaitchison
@calumaitchison 6 жыл бұрын
That happened with my dads boat....only we were on the slipway and just got the boat launched
@mitchellsummerfield7785
@mitchellsummerfield7785 4 жыл бұрын
Hi mate a good guide for the mechanicaly challenged ,not completely useless with spanners my self , but first time I've done wheel bearings on a boat trailer ,mine was a little different they were integral wheels(hub and wheel in one) same principles,only thing I did was clean intire in side of the wheel hub,to remove all traces of old Grease and contaminants,same thing with axle.thank you very much for your guidance.
@Ruffasgutz
@Ruffasgutz Жыл бұрын
part way through replacing my trailer wheel bearings when I got a bit stumped on how to get the seal into the hub. Googled and watched a shit super cheap video that was not much help until I found this video which pointed me in the right direction. I should have watched it before I started as it would have saved me some grief. Thanks for posting
@Do-iz6qd
@Do-iz6qd Ай бұрын
Cheers mate for the video....just a FYI I rang up a marine dealership and they wanted $670 to change bearings out on a single axle trailer + what ever else they find along the way!
@tomharrell1954
@tomharrell1954 5 жыл бұрын
Great video! I have done hundreds just like that! if you have a slide-hammer another way is use it to remove the races. I find it much easier!
@davidgordon5999
@davidgordon5999 4 жыл бұрын
I have found that if you cut a 1mm wide slot right through the old bearing race it makes it much easier to remove once the new race has been knocked into place. You can then keep the old race for future jobs.
@tunstallgeo
@tunstallgeo 3 жыл бұрын
Your tutorials are amazing. Just been working on my boat trailer and can't quite get the cotter pin in so think one of the races is out of place. I'll go take another look. Really appreciate these videos so helpful! Thanks from NZ
@michaelj38
@michaelj38 8 жыл бұрын
Excellent video! Your last comment was very sobering. "make sure the grease you pump into the bearing buddies is compatable with the bearing grease and marine grade." My grease gun has general purpose grease. I will knock them off, clean them out and get the correct grease. Thanks.
@DangarMarine
@DangarMarine 8 жыл бұрын
Hi Mike. I wouldn't lose any sleep over it, particularly if you are boating in fresh water. When you do get around to changing just make sure they are cleaned thoroughly before changing type of grease in case they aren't compatible.
@Fretboard_Chaos_Productions
@Fretboard_Chaos_Productions 8 жыл бұрын
Fantastic video mate, and the things that you say go wrong or it should be easier than what we see just gives us amateurs some more confidence in ourselves. Thank you for taking the time to make this video, it greatly appreciated.
@DangarMarine
@DangarMarine 8 жыл бұрын
+Peter Neal You're welcome Peter, I'm glad you enjoyed. And yes, it goes wrong for everyone, no reason to ever doubt yourself!
@mattc3303
@mattc3303 7 жыл бұрын
Wow, awesome video mate. I spent a while looking through videos on here hoping to find something with such detail. Being Australian was a bonus :)
@DangarMarine
@DangarMarine 7 жыл бұрын
Thanks Matt, hope the video helped you. :)
@paulmyers560
@paulmyers560 7 жыл бұрын
Well done. Great narration. Not to much, not too little. Enjoyed your patience on the difficult removal!
@alnbaba
@alnbaba 8 жыл бұрын
Great video, I've seen people torch off the race or use a small cutting wheel on stuck races. Salt water makes everything more difficult, the torch is pretty essential to free up just about everything.
@DangarMarine
@DangarMarine 8 жыл бұрын
+alnbaba Yes, I have seen some races cut out, and it isn't such a bad thing to do as the new race will give the bearing a nice clean surface to run on. You are also right about the torch. It comes out almost every single day!
@saltymammals
@saltymammals 6 жыл бұрын
Big thanks for all the videos you create! Very straightforward and easy to follow, as well as good troubleshooting tips for common problems that people might encounter. Your work is very much appreciated. Cheers!
@DangarMarine
@DangarMarine 6 жыл бұрын
You're welcome. :)
@bigwheelsturning
@bigwheelsturning 5 жыл бұрын
Glad I'm not the only one who has problems with that 'one thing" that just won't move. You are correct; it's sometimes easier to just buy a new hub with the outer races already installed.
@randy7986
@randy7986 5 жыл бұрын
I have seen tire shops do this time and time again and it drives me crazy. They hammer the lug nuts on with an impact wrench and THEN put the torque wrench on the lugs. By doing that, you have already surpassed the torque rating spec. Yea I know, I've heard the argument that they have their air pressure set for 90psi and torque to 125 but tell me, why doesn't the lug nut move when torqueing down to 125. The idea is to lightly set the lugs snug and then torque them up to spec with the torque wrench. Great tutorial! keep em comin mate.
@DangarMarine
@DangarMarine 5 жыл бұрын
Our impact gun has torque settings on it and the lower ones are well below the 110Nm the wrench is set to.
@dougbryer3090
@dougbryer3090 8 жыл бұрын
Hey Stu ! Thanks again. Did my bearings today. Not that bad. Getting that rear dust cover to set was a little tricky. All went well. i did your little dance for good luck before I did the job in the driveway before i did the job ! I owe you a beer, thanks ! Doug.
@DangarMarine
@DangarMarine 8 жыл бұрын
Hey Doug, nice work on getting your bearings done. I think people are mad if they attempt any sort of job without first doing a dance to appease the gods of corroded parts. :)
@petervany4342
@petervany4342 7 жыл бұрын
Great video. Good to see when things are a little difficult like needing to use the heat to show what problems that can occur. Thanks
@DangarMarine
@DangarMarine 7 жыл бұрын
Thanks Peter, a bit of heat sure goes a long way with stuck bearing races.
@yeliabttam
@yeliabttam 7 жыл бұрын
Great series of videos. One tip while pumping grease into the Bearing Buddy...STOP before the spring is fully compressed. It is very easy to blow out the rubber seal if you pump in too much grease. Don't ask how I know this.
@DangarMarine
@DangarMarine 7 жыл бұрын
Good tip mate, we all learn the hard way some times. :)
@yeliabttam
@yeliabttam 7 жыл бұрын
Unfortunately some of us have to do it twice before the lesson sinks in. :) Again, great videos. Just stumbled on them a few days ago while looking looking up something about knots, I believe. It's obvious you have a lot of knowledge and share it with a good, relaxed, clear style.
@jamminwithpops
@jamminwithpops 6 жыл бұрын
There is a small hole on the outside shell of the buddy. Grease will come out of the hole when enough is pumped in.
@Csqd1975
@Csqd1975 Жыл бұрын
Great video found tip on prefilling the buddy good idea. Just a point if you cut through the bearing cup you are using to drive in the new cup with a angle grinder with a cutting disk to split the ring on the edge it will come out easy.
@didge110
@didge110 Жыл бұрын
Yet another sensational, accurate and informative video Stu - very well thought out and taught. I saw quite a few others that lack so much of the detail you clarified.
@warrenbartlett6405
@warrenbartlett6405 2 жыл бұрын
Thanks so much for this video. I have only ever done wheel bearings with a mate years ago and this is a great video for us amateurs. Excellent idea to use the old races to hammer the new ones in place. Thanks mate.
@Fretboard_Chaos_Productions
@Fretboard_Chaos_Productions 3 жыл бұрын
Still my go to video to remind me about the tips and tricks especially for removing and installing the new races. Awesome video as always.
@robinstanford6025
@robinstanford6025 2 жыл бұрын
I think it's great that the job doesn't go straightforward because they never go straightforward either so seeing the problems that will arise and how to overcome them is superb. It's a bonus not a drawback!!
@faridjahed
@faridjahed Жыл бұрын
I will have to open up my trailer hub and grease it in abundance. Thanks a lot
@Harbs2Max
@Harbs2Max Жыл бұрын
Thank you. Fantastic video well thought through and great instructional video.
@philipallen6921
@philipallen6921 5 жыл бұрын
Thanks for video it was big help. When it came to getting out the old bearing outers there where two small slots cast into the hubs to allow a tool to be used to hammer them out . I noticed the one you had was well stuck so the slots helped. thanks again
@DangarMarine
@DangarMarine 5 жыл бұрын
You're welcome mate, glad the vid helped.
@georgedrager-bluewaterdreamer
@georgedrager-bluewaterdreamer Жыл бұрын
I watch this every year before I change them to be sure. Thanx mate cheers from rockhampton
@freeelectron8261
@freeelectron8261 5 жыл бұрын
Nice work DM - you show all the important tricky detail the others leave out! Thanks!
@DangarMarine
@DangarMarine 5 жыл бұрын
Thanks mate. :)
@xzxz-uy2lm
@xzxz-uy2lm 3 жыл бұрын
Been a few years since i done any bearings this was a great refresher Thanks !
@nickserafin76
@nickserafin76 5 жыл бұрын
Nice honest video and no wasting time. If we meet one day I'll buy you a beer. Double thumbs up.
@DangarMarine
@DangarMarine 5 жыл бұрын
Thanks Nick.
@robbynelson3
@robbynelson3 7 жыл бұрын
Forget this! I'll just buy a whole new setup with pre-pressed races and bearings and install a new one! Thanks for saving my rear!
@DangarMarine
@DangarMarine 7 жыл бұрын
That certainly is a nice easy option. sometimes the inner sections of the bearings can get stuck on the axle (Murphy's Law), but it is generally a faster swap over.
@ipyonoti
@ipyonoti 2 жыл бұрын
Thank you very much for this video. By far the most detailed and comprehensive video I've seen about bearing replacement
@jamesfackenthal
@jamesfackenthal 6 жыл бұрын
When installing the new outer races using the older ones take a flap wheel on an angle grinder and slightly reduce the outer diameter of the old bearing race. That way you won't have to beat the old races out once the new ones are in.
@andrewtaylor9615
@andrewtaylor9615 5 жыл бұрын
Or cut through one edge. You can use them wrong way round and they work better and are easy to flick out with a common screwdriver.
@TheScotth89
@TheScotth89 7 жыл бұрын
My pop showed me a trick for getting bearing races out, put a big bead of weld with very little penetration on the race itself, when the weld cools it will shrink the race by a few thou and it will practically fall out.
@DangarMarine
@DangarMarine 7 жыл бұрын
Yes, I've had good success with that technique too. It can really work wonders if you have a welder on hand.
@6981bpd
@6981bpd 3 жыл бұрын
Great video. Nice to see a little struggle getting old bearings out. I’ve watched many fix it videos that made it look much easier than it ever is when attempting myself... great in-depth video! Thanks
@rodneygreen9968
@rodneygreen9968 5 жыл бұрын
You made it clear on how to push the Marine Grease through the bearing, to fill it properly. THANKS Again.
@NCSUME1
@NCSUME1 5 жыл бұрын
great video. Fact of the matter is, most folks don't do regular bearing maintenance and what you went through is the norm. Greeting from North Carolina
@johnwaddell8390
@johnwaddell8390 Жыл бұрын
Great video thanks, very helpful as I had never changed my bearings on a boat with breaks. Apart from some rusted out bolts in the break calipers, it all, went smoothly
@fitafter5020
@fitafter5020 6 жыл бұрын
I've finally done It! After much determination and making up some tools I have finally extracted the bearing races, stainless bearings here we come....if you heard a Tarzan cry that was me lol Update! I was mislead they don't make stainless bearings for trailers, or at least not in the UK maybe you guys will have better luck than me, so after all that I had to fit standard bearings albeit with bearing savers.
@DangarMarine
@DangarMarine 6 жыл бұрын
Glad you got it sorted. :)
@fitafter5020
@fitafter5020 6 жыл бұрын
Wow! Someone replied lol I always feel a bit stupid commenting on old video's but I guess you do read them, thanks for that, I have one issue with my motor and I was trying to find a video that deals with the problem, I have a 2002 Yamaha 70hp 2 stroke BETOL and every year it seems to drain 2 stroke oil into the bottom cylinder and then down the exhaust depending on the position of the piston in the cylinder, the problem is when I start the engine up if it's been stood for a few months over the winter it smokes like hell! Once it has got hot its fine and for the rest of the season, after the oil from the exhaust burns off it doesn't smoke anymore but that initial start up is unreal!! I just wondered if you have came across this before? You think maybe It needs a new injector pump? Its done about 160 hrs but the engine is Immaculate very well maintained
@dickmorriss
@dickmorriss 8 жыл бұрын
Other than running a weld around the bearing shell to remove it, bearing pullers that use a slide hammer work a treat too. Good video as usual. Cheers
@DangarMarine
@DangarMarine 8 жыл бұрын
Thanks mate, I'll have to give the slide hammer a go next time. :)
@benjaminjohnson7033
@benjaminjohnson7033 8 жыл бұрын
Stu.... I love the videos and have learned tons from them. This may be a tip your are familiar with already, but I use my wire feed welder to heat the races up by welding a bead on the inside of each race. This weld causes the thermal expansion and thus shrinks the race as it cools. Keep them videos coming................
@DangarMarine
@DangarMarine 8 жыл бұрын
Hi Ben, I have heard that, but I've never tried it myself. Next time one is this stuck I'm going to give it a go!
@kenrisse1336
@kenrisse1336 2 жыл бұрын
Just finished my first bearing replacement -thanks for the detailed video, helped a lot.
@gordonpeden6234
@gordonpeden6234 5 жыл бұрын
Just stumbled across this channel being a boating "Tragic" I love it, every aspect! Re: life on or near the water. Regarding your comment "everything seems to be harder to do than it should" Just about sums life up in the real world, anything worthwhile is made sweeter if you have to struggle a wee bit harder to achieve. I love your tenacity, the way you punch on through. Cheers keep up the good work.
@James-hb8qu
@James-hb8qu 2 жыл бұрын
I've see a number of videos on bearing replacement and I agree with others that showing how to work through the issues that will come up makes your videos especially useful. I do worry at 22:52 that you contaminated your bearing grease.
@darrenb66
@darrenb66 7 жыл бұрын
hi mate, loving your vids, i have binge watched a few hours of them. i have a simple little trick that may work sometime, if you have a mig or stick welder and the outer races are stuck in the hubs, run a little weld around the races, it will shrink them when the weld cools just enough to make them easier to tap out. keep up the good work, i will be buying a t shirt
@DangarMarine
@DangarMarine 7 жыл бұрын
Hey Darren, yes, I've had really good success with that technique in the past. Some times they literally just fall out. Don't forget to send me a photo when your t-shirt arrives!
@journeyintosailing7649
@journeyintosailing7649 Жыл бұрын
This is a great video, rarely have I seen such a good explanation of any process. Thank you very much
@nidzdotnet76
@nidzdotnet76 3 жыл бұрын
Very helpful. Thanks! I also have trailer with brakes so this works perfect. It's good that you show all the stuff-ups because when I see that something should take 5 mins and ends up taking me 50, i wonder what i'm doing wrong..
@tomroot6013
@tomroot6013 6 жыл бұрын
Good Points, ALL! I have had 2 Situations, myself where it was pretty disasterous outcomes! First I had a 17' Bow Rider, trailer where I did my very first Wheel Bearing R & R, and Repacking! I was Moving, and a Friend needed to go in the Very Same Direction. So, I allowed him to put his Personal Possesions in the Boat to head a Couple of Thousand of miles and then retrieve my Boat from him, at the other end! Two days out, I get a Phone Call from him, and he said that the Boat Trailer had Lost the Whole Spindle, from a Bearing failure! The Boat was Destroyed, but fortunately No One was Harmed, and the only thing Damaged was my Boat and Trailer! (OK, my Pride a bit also!) Now, I didn't see his load, and he could have overloaded it, and I will never know! But this taught me a Valuable Lesson, as well! I have packed Dozens More since then, and was extremely carefull in just how I performed this task! All Points given here, in your vid, are Spot On! The 2nd Incident was when I had a Bearing Buddy I removed from my New trailer, and installed it on a boat/trailer I was selling, as that one was leaking! I used my Boat, a 26', a few weeks after and failed to replace it on the New Trailer! Well, just One Dunk, in the Briney, was enough to destroy it! I went about 10 miles or so, down the road, and someone got my attention and said that the Wheel was smoking! I got safely into a Shopping Mall Parking area, and Long Story Short, could not get assistance on a Saturday Night, nor the Next day, either! ! I had to be at work on the next Monday, so I Improvised. I was able to get a New Bearing Set, at an Auto Parts Store, Tools, and Grease, to repair it! The Spindle was in Good Shape, except the Bearing Surface was Sloppy, due to it being worn, from the Inner Race of the failed one! Off to the Auto Parts Store, 10 Minutes before they closed and Tubes of JB Weld, file and some Sandpaper did the trick! About 7 hours of Grief, several hundred miles from home, I did make it home! That same Fix has Held for 12 years now, and about 30K Miles. I have had the bearing off several times for inspection, and it is still perfect! No degradation whatsoever! I was Lucky, as Both situations could have easily turned out Deadly! I just added my story, so others learn by My Mistakes! I will give JB Weld much credit, as I have used it so many times over many decades with Perfect Results! One Engine Block on a VW Vanagon Diesel Aluminum Engine, has held for 25+ years now!
@timjohnun4297
@timjohnun4297 3 жыл бұрын
One tip I've found, if you don't have a vice or a work bench (Like me), bolting the rim back on the hub works, you can knock the old races out and install the new ones on the floor without doing any damage to the hub (Or the floor)
@Vincent_Sullivan
@Vincent_Sullivan 3 жыл бұрын
Similarly, I use a scrap brake disk in roughly the same way. On most rims the rubber of the tire protrudes beyond the metal of the rim. Using the rim as you suggest usually means the rubber sidewall of the tire is supporting the weight and its "bounce" will take a lot of "zing" out of your hammer blows.
@timjohnun4297
@timjohnun4297 3 жыл бұрын
@@Vincent_Sullivan yes, correct, but that bounce also protects the concrete. If I damage the concrete I have to answer to the wife 🤣
@Vincent_Sullivan
@Vincent_Sullivan 3 жыл бұрын
@@timjohnun4297 I can't argue with you on that one... Maintaining domestic harmony takes precedence! I did this job recently on my utility trailer and in my case I bolted my hubs to a scrap brake disk and then clamped the brake disk to a corner of my welding table with a couple of Vice Grip style clamps. This worked very well to hold the hub in position while I hammered on the races with a club hammer and a drift. the old races popped out with no problem. No heat required. The new races went in using a seal driver and the club hammer also with no problem. No cooling or heating required. Lucky me!
@robertstutsel8702
@robertstutsel8702 2 жыл бұрын
Just a couple of points to note. 1. You need to check what bearing numbers you have by pulling it apart before buying bearings. 2. By testing my hub with a Falcon wheel, I found that I had the Ford stud pattern. I assumed that I would have Ford bearings but alas I have Holden bearings in a Ford stud pattern hub. 3. Great video. I recommend a bit of heat. I used a little burner on a little throw away butane gas bottle. Last time I did a trailer bearing was years ago but a good trick is to make one cut through the old bearing shell and it will make pushing the new shell in easier and very easy to remove once the new one is in place. 4. I am going to get a spare hub to mount my hub on the boat but for some reason they generally only supply them with “one trip” bearings. I will be trying for a Timken bearing or equivalent.
@garyrish
@garyrish Жыл бұрын
Thanks this is very helpful as others have said thanks for not editing the hard bits so we all have some work arounds when we encounter the same issues
@yindyamarra
@yindyamarra 6 жыл бұрын
Great vid, I’m going to be using this as a step by step in the next week or so in my shed,
@DangarMarine
@DangarMarine 6 жыл бұрын
Thanks mate, good luck with the job.
@sheldonoetter3935
@sheldonoetter3935 4 жыл бұрын
HAH, Brilliant! Thank you Dangar for saving me a trip to my auto store to rent a race installer punch. I had the same idea of using the old race as a punch, But as you mentioned, I was thinking of using it the wrong direction. I slightly growned down the OD of the old race on the grind wheel so it would fall out easily after use.
@62chevrolet
@62chevrolet 5 жыл бұрын
If you weld a really hot and nasty bead on the running surface of the race, when the weld cools, it will contract and pull the OD of the race smaller and they often fall out. It works really well on tractor-trailer hubs.
@DangarMarine
@DangarMarine 5 жыл бұрын
Yes, I've done that a few times, can work well. :)
@mikejenkins4598
@mikejenkins4598 5 жыл бұрын
In the US Marine grease I believe is always blue green in color no red there is a difference red is for highway trailer use
@jamesbach2021
@jamesbach2021 4 жыл бұрын
I enjoy your videos and this was another good one. As mentioned before, putting the bearing races in the freezer for a while will aid in the installation. I trailer my boat all over the Great Lakes in the United States to get to different dive sites. Whether I am going to a marina that's five miles away or three hundred, after I have driven a few miles I stop and feel the hubs. They should be warm, but not hot! If they are hot you may have a problem. Bearings always fail when you are in Timbukto, so it's worth while to check. I use bearing buddies and they work great. However, if your just getting on the freeway and hear a short whirring/buzzing sound, one of your bearing buddies has just parted company with your trailer. LOL
@vetterfellow
@vetterfellow 6 жыл бұрын
Thanks Stu; I'm looking at the same job as soon as it's warmer outside. This is a good reference vid. for me.
@DangarMarine
@DangarMarine 6 жыл бұрын
Hey Angelo. Good luck with the job, trailer bearings certainly need a bit of TLC from time to time.
@sandosau
@sandosau 6 жыл бұрын
Red hot tip #2; when using the old race to punch in the new one, cut a slit in the old one so it it's sort of like a roll pin. File, grind, sand the edges of the slit smooth, then use that to punch it in. Dead easy to get out with a pair of multi grips, that is if you can't get it out with fingers.
@DangarMarine
@DangarMarine 6 жыл бұрын
I like that idea, I'll give that a go next time too!
@wilsnich02
@wilsnich02 3 жыл бұрын
Great video, no one every explained how to tell if it is a Holden or Ford Bearing short of what the wheel stud pattern is it, now I know square 45 mm or round 40 mm. I will probably make it easy on myself and buy the hub and bearing together for a quicker and easier job. Things not going right is real world and great to see. Love you video's and I get lots out of them, Cheers
@VT1100tbo
@VT1100tbo 5 жыл бұрын
Just a tip. When to mount the new bearings. Warm up the hub and get the bearings in the freezer. Then the metal in the hub has expanded and the metal in the bearings shrunk. In this way, it is much easier to push the bearings in.
@seanc3362
@seanc3362 5 жыл бұрын
Oh those races were hard! I see why shops use a press now. Great video!
@doglegjake6788
@doglegjake6788 5 жыл бұрын
that looked like a gravy job with biscuit wheels !! great job !!
@markfindlay8636
@markfindlay8636 4 жыл бұрын
I always heat the hub before hand it's a lot easier. I also just tap the inner bearing from the opposite side as it saves prying off the seal and avoids damage if you want to reuse.
Trailer Wheel Bearing Replacement Guide
1:05:48
Easy Fix
Рет қаралды 364 М.
Pt.1 Boat Trailer Bearing Service At D-Ray's Shop
10:02
D-Ray Smith
Рет қаралды 630 М.
Prank vs Prank #shorts
00:28
Mr DegrEE
Рет қаралды 11 МЛН
managed to catch #tiktok
00:16
Анастасия Тарасова
Рет қаралды 48 МЛН
He bought this so I can drive too🥹😭 #tiktok #elsarca
00:22
Elsa Arca
Рет қаралды 13 МЛН
Bony Just Wants To Take A Shower #animation
00:10
GREEN MAX
Рет қаралды 7 МЛН
Trailer Bearings and Races: When Should They Be Replaced?
20:29
The TrailerSmith
Рет қаралды 15 М.
How To Replace Boat Trailer Bearings | BoatUS
15:22
BoatUS
Рет қаралды 771 М.
Trailer Trauma! DIY - Wheel Bearing Basics
26:50
Captain Leon's Boating and More
Рет қаралды 229 М.
How to Replace a Front or Rear Wheel Bearing (Full ASMR)
16:09
ChrisFix
Рет қаралды 2,3 МЛН
How To Repack Trailer Wheel Bearings
22:25
Wayne The Boat Guy
Рет қаралды 247 М.
How to Repack Trailer Wheel Bearings [Start to Finish]
11:55
Adventure Rig
Рет қаралды 946 М.
Complete DIY Caravan Service, Brakes, Wheel Bearings
28:12
Van On The Back
Рет қаралды 33 М.
How to replace Erdé trailer wheel bearings
30:41
bootsowen
Рет қаралды 7 М.
Prank vs Prank #shorts
00:28
Mr DegrEE
Рет қаралды 11 МЛН