Delonghi ECAM 23.450.S teardown and infuser carriage repair

Рет қаралды 73,018

3 жыл бұрын

My old espresso machine had been acting up so I decided to take it apart and see if I could do something about it.
There was a a lot of play on the carrier mechanism shaft. Turns out the nut that tightens it to a sort of bearing had gotten loose.
I hope this helps anyone who also is having trouble with their Delonghi machine.

Пікірлер: 24

@user-jm3ep2fi6s 2 жыл бұрын

I got a cramp in my head while I was looking at this mechanism. You're a great engineer 👍

@scorpion1982a Жыл бұрын

Zaczepy od wyświetlacza pięknie uszkodzone. W życiu dołem wyświetlacz się nie będzie trzymał. Wyświetlacz odchyla się i przesuwa do góry. Ludzie nie uczcie się od tego Pana !

@ShaniAce 3 күн бұрын

What kind of screwdriver is needed to remove the backplate?

@magdylast9408 3 жыл бұрын

Good job Thank you

@Bagan95 2 жыл бұрын

Thank you for the video! I have problem with milk not working/frothing or sucking into the plastic straw. The water seems to be working fine from the water sprout, and do get hot. I got no continuity though, on one of the two white temperatures sensors 318C, that you showed in the video 5:44 timeline. Anyway I’ve ordered a new one of those. Sadly, could not find the exact one to match my model number. It looks the same, so I hope it works. Question: I can not find the exact solenoid valve that match with the one I have. The numbers varies between 5301VN10P46AIX and mine 5301VN27P50APX. Are they working differently or is it fine buying even when different number? Both for Delonghi of course. I wonder if it’s possible to order a similar one but not the exact correct model number. Do you know if it will work with a different one or you know where I can find the exact one? Gear I have: Machine - ECAM23.460.B Solenoid Valve (top one, no sound/hummeling) - 5301VN27P50APX Thermostat - 467E // Tf 318C // 155431078N Thank you a lot.

@hubertbarrantes4604 Жыл бұрын

Hello. I cannot remove the transmission before the infuser is stuck and I cannot manually remove it. Is there a way to still remove transmission?

@tomasp3394 Жыл бұрын

Sounds like a sensor (more like a switch pressed by infuser carriage moving too far along its axis of travel) is not triggering. I simulated this behavior while troubleshooting my ECAM which had trouble with sensor counting rotations and refusing to work after self diagnosis cycle.

@hubertbarrantes4604 Жыл бұрын

Hello. We’re you able to fix that issue? Mine makes a bad noise then it says general alarm. Troubleshooting says upper and lower switch on transmition need replacing

@DrMary32 Жыл бұрын

Hi! I have same machine but the issue might be different, it doesn’t respond to commands, if is plugged in, is playing alone: switching on and off, water comes out and in the end I cannot make any coffee as buttons are not responding to orders. What that might be? Thank you!

@bunyaminejder3334 3 жыл бұрын

Hallo, Was ist den bei Delonghi Kaffemaschine obk? Danke für den Antwort.

@jeane3809 2 жыл бұрын

good share

@magdylast9408 3 жыл бұрын

Few months now since you post this video? Did the machine show this error again?

@tobiassytsma9077 3 жыл бұрын

No, it's been working great since, it's probably made 250/300 cups since the repair.

@magdylast9408 3 жыл бұрын

@@tobiassytsma9077 Good , mine is got the same problem and wanted to know if its long-lasting repair or not, but now I know Thank you

@tobiassytsma9077 3 жыл бұрын

@@magdylast9408 Be sure to check out this video as well, he shows the transmission in more detail. kzfaq.info/get/bejne/fsBoorSGrNq0mpc.html

@naderebrahimi9905 7 ай бұрын

Hi, I have an DELONGHI ECAM, I fixed the clogged tubes but when i take the infuser out and clean and placed it back, the machine keep displaying "INSERT THE INFUSER ASSEMBLY" and no matter what i do, machine keep displaying the same message. Any idea why??

@ProBeuno 7 ай бұрын

This is exactly what my issue was. Look for play on the infuser carriage. If there is play, disassemble machine and tighten spindle nut

@krasimirkaramanov1982 2 жыл бұрын

I can't understand what be wrong?

@Denisjjj 2 жыл бұрын

In my machine the piston of the infuser doesn't reach the upper position but stop at 3-4 millimiters from the top: the result is that a part of the coffee ground remain on the filter. Who know which is the problem?

@PeugeotStuff 2 жыл бұрын

Infuser may not be assembled correctly. Make sure that when the arm is in the down-most position, the piston is flush with the infuser housing. If not, take it apart and re-assemble with the gears lined up properly.

@Denisjjj 2 жыл бұрын

@@PeugeotStuff manually pushing the piston it reach the right top level. I think it depends from something during the process but i cant understand what. Everything seems right