Delta has a sweet spot on my heart. Never had a problem with them. Kohler on the other hand 🤣
@sittingbull16111 ай бұрын
Be a plumbing gentleman and grease the nut that holds the cartridge in and also the set screw and handle and of coursethe cartridge. Things will come apart in 10 or 20 years
@foundationalblackamerican168210 ай бұрын
The plumber in you had to say this and I’m glad you did as a newbie.
@Chris.Rhodes11 ай бұрын
That lock nut/ring is always fun when you have to cut it because it's so old, and someone used pliers to put it on, and hope you don't ruin the threads of the diverter valve... I've done that twice. Not a fun day.
@stephenparsons527811 ай бұрын
Installed the exact one this week
@otisbigsby11 ай бұрын
Before putting all the trim on turn on the water and check that cartridge for leaks.
@Manuelgtrrz11 ай бұрын
i replace a lot of valves with delta’s because of their ease.
@briancaudill6673Ай бұрын
Oh so you j change the cartridge and that automatically replaces the valve somehow, wow that was fN magic
@Greengoooo11 ай бұрын
U 4 got the white spacer for the chrome sleeve
@Seven7Pain111 ай бұрын
Fail they will be calling saying not enough hot water you didn't turn scald guard up 😊
@George-yd7cx25 күн бұрын
It's not going to hurt a thing to tighten the locking nut down with Chanel locks
@salone160526 күн бұрын
If I can't get that nut ring off I go straight into cutting it off. I allways have them rings on hand. In my past 7 of 10 are stuck.
@brandonwardlow13182 ай бұрын
Faucet grease, and scald guard.
@alherrera9920Ай бұрын
Installed this valve last week but notice that the cold side has more volume pressure than the hot side when i shower. Is that a safety feature or is it a defect in the cartridge? I tried adjusting the cartridge but when I turn the handle all the way to hot the pressure is less than the cold side.
@shawnrossi636411 ай бұрын
Use grease it'll make plumber impressed
@pauljenkinson28703 ай бұрын
So simple. Wait till you do bristan shower.or a Rada the shower.
@Realmicahsumner11 ай бұрын
Silicone grease boy!
@whattheschmidt11 ай бұрын
Foam gasket.
@Realmicahsumner11 ай бұрын
@@whattheschmidt I think you may be confused
@whattheschmidt11 ай бұрын
@@Realmicahsumner yeah I read this as caulk, oops
@MaMa-qh4dy11 ай бұрын
Sometimes those cartridges are SO stuck. You just gotta work at it.
@chrisk.6849Ай бұрын
Call back Water not hot enough.
@The.Hangry.Comment11 ай бұрын
So which is better and easier, delta or moen cartridges?
@Realmicahsumner11 ай бұрын
Delta
@troylitle31162 ай бұрын
Fuck moen
@evanv60211 ай бұрын
no grease for the cartridge???
@bigdaddystovepipe2 ай бұрын
Delta Ashland, looks good but the pop up rods on the faucets suck!!!
@1stCamarillo11 ай бұрын
Is this a R 10,000 Valve
@anthonyurban258911 ай бұрын
set the scal-gaurd....
@Bryan-wq1ng11 ай бұрын
Ok experts. What do you have to say???
@Jman126211 ай бұрын
The big hole 🤣🤣🤣
@IrrationalBstrd5 ай бұрын
Typical delta shower valve. Installer followed the instructions, and now it sticks way too far out of the wall, to where the trim barely covers near the handle. It looks like ass. Don't use the black plastic trim piece to set you're depth, that's out way too far. Use a 1 x4 instead of a 2x4, thank me later. If you don't follow.my advice, you'll end up with that unsightly gap between the cylinder trim body and the handle. Not acceptable in my book.
@BathroomRemodelingTeacher5 ай бұрын
That’s a load of crap for sure. Been using delta valves my entire career.,set a 2x6 block to back of a 2x4 wall and bam your good to go for most tile installations
@IrrationalBstrd5 ай бұрын
@@BathroomRemodelingTeacher I'm doing it right now, and mocked it up putting all the trim on, it's out way too far for my liking, and the cylinder trim barely covers. If you look at the slight angle, you can see the plastic behind the base of the handle. That's way too far, in my opinion. Edit: following their instructions with the black plastic trim plate to set depth, puts the face of the handle out 4 inches from the finished wall... That is ridiculous, and it looks like crap. There is no reason for it to stick out that far. Most tile installations probably 7/8 - 1" from the studs, and I'm changing my stringer out to a 1x4.
@BathroomRemodelingTeacher5 ай бұрын
@@IrrationalBstrd my suggestion stick to what works for you and stop your bitching 😆
@IrrationalBstrd5 ай бұрын
@@BathroomRemodelingTeacher well, I appreciate that, it was very helpful. I don't care to have the plastic mixing valve visible under the handle on finish. On this particular model, I'll probably have to zip off some of the cylinder trim at the back
@handyman332011 ай бұрын
What in the world is up with that niche
@whysoserious79142 ай бұрын
Bro why are you out of breath?
@stillmatic0311 ай бұрын
Don’t forget to adjust that anti scalding if you live with a woman 😂
@Unionmade69245 ай бұрын
Delta always has some goofy valves or fittings. Just keep it simple.
@lxn_ni181411 ай бұрын
Use a drill not an impact on the lowest setting and ur good.
@efraimmedina167527 күн бұрын
Didn’t check or engaged heat tab
@Mggggssss11 ай бұрын
Hey boy, back in my day we didnt have no hot water