Don't Install Trailing Arms Before You Watch This! Ultimate Land Rover Discovery Build Episode 28

Рет қаралды 78,274

Күн бұрын

Let's talk about Trailing arm rear suspensions! On the right 4x4, this offroad suspension style can be a huge asset. Freeing up some space, building a beefy lower link, and using a smaller Coilover are big advantages. BUT there are two sides to this story! I don't recommend Trailing arms for most offroad builds. They add complication to the initial setup, add weight and even reduce ground clearance. In this video, I want to help give you the basics so you can make a decision that will appropriately suit your project. Enjoy this video! Next week we will get this Landrover Discovery on the trail to test out these new mods. See you then!
AMAZON ITEMS!!! www.amazon.com/shop/dirtlifes...
(Amazon Affiliate Links)
BARNES 4WD COUPON CODE: "dirtlifestyle" 10% off
NORTH RIDGE 4X4 CODE: "dirtlifestyle" up to 20% off www.northridge4x4.com
DOMETIC: bit.ly/3zPPRwN
ONX MAPS: webmap.onxmaps.com/account-pu...
EMPIRE ABRASIVE CODE: "dirtlifestyle" 10% off lddy.no/qf79
YANKUM ROPES CODE: "dirtlifestyle" bit.ly/yankumDL
MIDLAND RADIOS: bit.ly/2IjmlZD
EVOLUTION POWER TOOLS CODE: "dirtlifestyle" store.evolutionpowertools.com/
JOOLCA HOT WATER HEATER: bit.ly/37qLgEp
Shirts & Hats on our website!!
www.thedirtlifestyle.com
Support us on Patreon! / dirtlifestyle
Follow me on social media!!
Instagram: / dirtlifestylenate
Facebook: / dirtlifestylenate
DiRTBAG MAFIA Facebook Group
groups/34277...
DISCLAIMER:
Due to factors out of the control of Dirt Lifestyle, we cannot guarantee against improper use or unauthorized modifications of this information. Dirt Lifestyle assumes no liability or responsibility for property damages or injury incurred as a result of any information contained in this video. Use this information at your own risk. Dirt Lifestyle recommends safe practices when working on vehicles and/or with tools seen in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Dirt Lifestyle. Be safe!
This video and description contains affiliate links, which means that if you click on one of the product links, I'll receive a small commission.
#offroad #4x4

Пікірлер: 187

@BentFabrications Жыл бұрын

Just a note to consider. When you put together a trailing arm and limit the movement for the shocks with a wobble stopper, you're keeping that arm vertical to the ground even at full flex. That means all the misalignment of the axle angle has to be available in the joint on the axle side. This is why we sometimes have to step up to a joint even bigger than a 1.25 heim with high misalignment spacers on the rigs with massive travel amounts and flex. Your axle on that may not articulate a lot on that particular build, but those Johny joint style joints are really limited, be sure to cycle the suspension to full flex and confirm that joint is going to be able to handle the misalignment you need.

@sloppyoppie Жыл бұрын

Yup. All those other joints are ok imo for low speed if you can justify a ding from dragging your rig across the trail with a limp control arm. My style is go fast so I now only go fast w/1.25 (or more) heims. A JJ almost killed me.

@hongmihnhahn7081 Жыл бұрын

But the bigger heim doesn’t mean more available angle ?

@DCOJos Жыл бұрын

Your next tool should be a lathe and you’ll never have to worry about sourcing issues. I’m sure you knew that already. 😊

@MacsSpecialitiesMotorsports Жыл бұрын

Amen!!

@branchandfoundry560 Жыл бұрын

When I got mine I didn't have a specific job in mind, just knew in my gut I needed it. I use it daily sometimes. Definitely the most valuable tool in a metal shop.

@badgermetal Жыл бұрын

Iv used a drill in a vice as a lathe to make custom bushings. Only works on softer stuff but it works.

@briandrose Жыл бұрын

You can almost certainly find your sleeve material/dimensions on McMaster. You're definitely going to pay a premium, but they have everything under the sun in stock. I'm spoiled because the warehouse is a mile down the road from me in SoCal.

@davesmith8936 Жыл бұрын

McMaster Carr will call in Norwalk. My happy place! LOL!

@loganrichardson5385 Жыл бұрын

For the sleeves, order some 3/4 rod and cut/drill to your length. Or I'm sure you could have a machine shop make you some also.

@scooterprint Жыл бұрын

Nate, you totally missed the opportunity to call this video "TROPHY TRUCK SUSPENSION SWAP" or something similar. Jokes aside, very happy to see something like this on your channel. I've always been interested in trailing arm style suspension, but haven't seen any good videos on it aside from the standard 4-link setups you'd find on a jeep/similar. Edit: I'd get in touch with ADS (Arizona Desert Suspension) about the bushing material and your coilover valving. I have spoken with them before about coilovers for my truck, and they're super cool people.

@VaanillaGorilla Жыл бұрын

Might be time to add a metal lathe to your arsenal of tools.

@DirtLifestyle Жыл бұрын

Man I wish!

@EngiTrek Жыл бұрын

Perfect time to get yourself a lathe! Make your own sleeves and then whip out a set of delrin bushings the correct length!

@nrhudec Жыл бұрын

FYI, your spring rate estimation is a bit off. To get the same effective spring rate you need to divide the current rate by the square of the motion ratio. New=current/(MR^2). So for example if you current spring rate is 300 lb/in and assuming the motion ratio is .75, then he would need about a 530 lb/in spring to achieve the same effective stiffness.

@gregsmithracing4479 Жыл бұрын

Came here to say this, and for example if your shock mounting was mid point(50%) of the trailing arm it would be a 1200 lb/in spring(300 lb/in effective wheel rate). I think Nate’s guess of 300 lb/in is high though. I don’t know his weight, travel, and target ride height, but my 7k lb land cruiser had an effective rate of about 130ish lbs/in. With less travel ~200 lb/in sounds more realistic.

@vincentbentley1079 Жыл бұрын

@@gregsmithracing4479 I guess in normal use the design is also factoring in the spring rate of a pressurized air-spring. However, if that air-spring is designed to be mechanically constrained by a coil spring, I have no idea what it will do without the containment.

@LukeEdward Жыл бұрын

THANK YOU! Even without the mathematical formula, take the opposite view of the measurement of torque. Moving out 100% further - or in reverse, 50% inward, you would be applying double the amount of force. If you are 3x out from the center, and you move to 4x length, that would be a 33% increase on torque, not 25%.

@branchandfoundry560 Жыл бұрын

Grateful you posted this info! Sitting here thinking it can't simply be linear like Nate's saying, but what do I know?!?

@thelonewrangler1008 Жыл бұрын

That trailing arm is a work of art. I'd definitely beef up those frame mounts too

@JW-cn6op Жыл бұрын

You definatley need a lathe.Even a bench top model would work for tons of smaller parts like this and keep you rolling through a project rather than waiting days or more for a part.

@DirtLifestyle Жыл бұрын

Hopefully one day

@AddictedCreationz Жыл бұрын

Nate, great episode. Got a tip for you for your forklift: convert your tank to a standard 20 lb grille tank. Easier & faster to fill (just swap), and you don't have to worry about tank recertification. I did this to mine and love it...

@nickcowley8757 Жыл бұрын

Love being able to see the changes in plan with the explanation of why! Super cool to see the process

@timcope6685 Жыл бұрын

It's always a good Sunday morning when I get to watch Nate building something and I get to learn at the same time! Suspension's are really interesting, the geometry involved is fascinating to say the least!! Happy Thanksgiving Nate and to all of yours!

@troydecker9685 Жыл бұрын

I really want to 4link my 1990 Suburban but it’s a daily driver and occasionally a trail rig. Thanks for the Trailing arm info. Just more information to make a educated decision

@gregtennyson Жыл бұрын

Thanks for inspiration to get off my ass and finish my bumper. Glad to see you making videos again ✌🏼

@DirtLifestyle Жыл бұрын

Get out there!!!

@chopperchuck Жыл бұрын

After 40 years of fab/welding I look forward to your videos to see what and how your going to build your next project , good job Nate

@DirtLifestyle Жыл бұрын

Thanks brother, I appreciate the kind words 🙏.

@DownNDirty_OffRoad Жыл бұрын

Been thinking about this setup and you are helping me a lot on questions I had. Watching this to the end for all the info I can get!!😃

@DirtLifestyle Жыл бұрын

Happy to help 👊

@chuckieswickedgoodfab Жыл бұрын

great explanation of trailing arm pro-con, it was very insightful. Always great content!!!

@BigFishOverlanding Жыл бұрын

The fab work you do is so cool to watch. Thanks for posting this man.

@scottyh72 Жыл бұрын

Thanks for bringing up shock valving. It is too often overlooked. I just revalved my Fox 2.0's, and made my leaf spring rig ride much nicer than the internet says it should.

@zd533 Жыл бұрын

Not sure if 4130 is the right material, but McMaster has .750OD, .620ID cold roll tube. Not sure if .005" on the ID will be an issue... The PN is 89955K599 Very informative video, definitely appreciate the time you put into these.

@michaeldurling793 Жыл бұрын

Yup McMaster was going to be my best suggestion, my experience is they have almost anything and everything under one roof.

@lifelinefabllc Жыл бұрын

Funny. I went straight to McMaster and found the same thing. They really don't have it. I doubt a plated bolt would fit .620 but maybe. I also think I would want something rust resistant for the bushing like stainless or 4140.

@skylinesandro Жыл бұрын

@@lifelinefabllc they have 0.634 ID which would probably be fine. That's part #89955K158

@DirtLifestyle Жыл бұрын

Thank you! This is certainly an option if I need it

@ratfarmers Жыл бұрын

Mmmmmm...... you said cake! That Evolution magnetic drill is now totally on my Christmas want list! Thanks! That Barnes arm kit is like metal legos for fabricators! Very cool!

@SWFabrication. Жыл бұрын

That trailing arm is pretty slick. Nice to see them not 55 or 60 inches long and as a WIY kit. Looking forward to the end result on this one.

@vincentcarriere183 Жыл бұрын

Super stocked to see à suspension video on this channel its the reason I subscribed in the first place 🙆‍♂️

@mikemorgan4670 Жыл бұрын

Very interesting. Always appreciate your explanations of the engineering. Thanks. Happy Thanksgiving to you and your family Nate!

@DirtLifestyle Жыл бұрын

Thank you! Happy Thanksgiving!

@Jeep.wj.tj.australia Жыл бұрын

It's always a pleasure watching you content 👍🏻

@talon0863 Жыл бұрын

For longer bushings, you can use 3 of those instead of two. Cut the third down to fit in the center.

@simon-mouse8739 Жыл бұрын

Exactly what I was thinking just cut a 3rd bush down to take up the slack/gap 👍

@davidlong3247 Жыл бұрын

Nice! Love to see fabrication.

@vetguy2562 Жыл бұрын

I can't even wait to see this build YEAH 🤘

@MacsSpecialitiesMotorsports Жыл бұрын

Excited to see how your experiment turns out for you!

@ryanaustin2617 Жыл бұрын

I love your upgrade series on the Disco 2. I own one and love it. If I ever win a lottery, I'll send my Disco to your shop (as a project, I know you are not a garage). Keep up the good work.

@Defender110SLO Жыл бұрын

Owsome arms you made. Insane. 😍 Cheers. 🍻

@georgemitchell8991 Жыл бұрын

Super interesting. I think I'm going to play with trailing arms soon. Thanks for the video!!

@DirtLifestyle Жыл бұрын

Thanks for watching! Good luck with the trailing arm experimentation 😁

@georgemitchell8991 Жыл бұрын

@@DirtLifestyle I really like what you said about the aluminum I had no idea that it bounces back. And I was thinking about doing the kind you're making but after you said it's not good for rocks I'm thinking differently now

@sas86toy Жыл бұрын

Love the extra metal wrap around, something I would of done🤘🏼

@randumadventures Жыл бұрын

Dam really making me reconsider all the time I put into my leaf spring setup

@holdthatdown6695 Жыл бұрын

Nate try ruffstuff for the inner sleeve

@BumDogSuMo Жыл бұрын

Yup. I made a wide busing mount for my Atlas and got a long 9/16 inner diameter sleeve from RuffStuff

@SHOOT_NDX Жыл бұрын

I love your Taco & all of your wheeling & building videos. I think you do a really great job. I’m also really impressed with your building, wheeling, breaking & then rebuilding the vehicles. Keep it up & I just bought a new Tundra if you’re interested in doing some work on it. LOL

@EricaMTB Жыл бұрын

Your maths for spring leverage is wrong. Moving the mount in 50% will increase leverage 100%. It's x/0.5=2x

@DirtLifestyle Жыл бұрын

Yep

@rjm7168 Жыл бұрын

I think your spring rate math is wrong. If your spring is located 25% short of the axle, then it's 3/4 of the way from the pivot point. So, since the spring moment arm is 3/4 the length of the axle moment arm, the new spring should be 4/3 (reciprocal of 3/4) of the original spring rate, which is 33% more - barring other changes of course.

@grabberorange5663 Жыл бұрын

Nailed it.

@nrhudec Жыл бұрын

@rjm that's still not quite right. To get the same effective spring rate you need to divide the current rate by the square of the motion ratio. New=current/(MR^2). So for example if his current spring rate is 300 lb/in and motion ratio is .75 like you assume, then he would need about a 530 lb/in spring to achieve the same effective stiffness.

@Jay-uh2jb Жыл бұрын

Yes, I hope he realizes the 25% and 50% he describes does not directly translate to spring rate increase he needs. The increase needed is far higher.

@DirtLifestyle Жыл бұрын

I completely agree and I want to elaborate a bit in the next episode. The problem is finding dead reliable equations that I can communicate to my viewers with confidence. I've seen a few different ways to calculate this, and all have a different conclusions. They way we are doing this is the basic rule of thumb to get us close, then measure what rate we need based on the sag of the springs we have. Not very scientific but pretty standard in the offroad world unfortunately. Finding this info online from a reliable source is tough but I will dig into this issue deeper in the next video 👍

@mikejensen-fogt4662 Жыл бұрын

Nate, once you have a lathe, things like that sleeve are never a problem for a build.... take a piece of 3/4" bar stock and punch a 5/8" drill down the center... I love fabricating! but learning how to machine took my fabrication skills to the next level! having a lathe and mill at home is so dang handy for things like that lol....

@vincentbentley1079 Жыл бұрын

It's an interesting project that I will watch to see how it turns out. Have you considered using a swaybar with disconnects (in cab control or manual) for the rear suspension? A rear swaybar would enable you to valve the shocks to precisely control bump and rebound, tuning the swaybar to control body roll for a better ride.

@artyseibert Жыл бұрын

Check out McMaster-Carr for the sleeves. They might have what you need

@hotflashfoto Жыл бұрын

A little bit of math for those who scratched their heads when Nate mentioned "25%": When you move the spring 25% from the axle, in order to keep the same ride height, the new spring has to be 33% stronger, not 25%. Use the reciprocal fraction: The spring is 3/4 of the distance from the front to the axle, so the spring has to 4/3 times as strong. Same for the shock valving. The following example includes some rounding to make for fewer fractions... Using Nate's example, imagine that the arm is 4 feet long. You move the spring so that it is now 3 feet from the front joint and 1 foot from the axle. If it had 400 lbs of force at the axle, then there is 100 lbs per foot of arm length. Now at 3 feet from the front joint, you now need to account for that lost 100 lbs of force. So, divide that by the 3 feet and you get 33 lbs, or 33% more spring force needed, not 25 lbs or 25%. That shows that the 400-lb spring would need 33% , or 133 lbs, more force, making it a 533-lb spring. If it had a 300-lb spring, then 33% more would make the new one a 400-lb spring. No matter what size it was, the new size or spring rate will need to be 33% more.

@jiggyquinn5635 Жыл бұрын

Thank you

@minimule1 Жыл бұрын

I have to say nice work I love the disco . I have a D1 and a RRC 2 door . My RRC I think in my mind has the perfect rear suspension because the load leveler in the back upper A frame allows for a lot of axle flex WAY more than a D1 ever had. If your loading up the RRC a lot you can still have a very soft ride and install a Defender 110 load leveler and it will carry a lot more weight . The axles will need to be up graded which is why I have a factory front and rear D60 . With the axle up can get for the D60 axles they can be built up super strong and still fit under a rover with out making a 1ton axle set up . Tony

@robbase2285 Жыл бұрын

Should do a video on shock placement on a rear axle. Front, rear or 1 front 1rear.

@kevinshaber8742 Жыл бұрын

I have 20' of 3/4x5/8 tube for exactly the same application. Be happy to send you some. I'll have to share my trailing arm setup when I finish in a couple months. Mine is going to be four-corner all air.

@ultra4suzukisamurai679 Жыл бұрын

McMaster Carr is a good source for tube for sleeves. Not the cheapest but convenient.

@richardworley2746 Жыл бұрын

Tractor supply has bushing sleeves. In a pinch that's where I usually go.

@PNW_Rodeo Жыл бұрын

There are a few companies that sell custom length builder bushings. On my Rodeo the oe bushing is 2.75" which isn't very common. I bought my custom length bushings from ruffstuff. 👍

@ItAintJustPaint Жыл бұрын

You can buy 3/4 steel tube @ Home Depot that’s 1/16 wall, that gives you 5/8 ID

@Fix_It_Again_Tony Жыл бұрын

That's not a bad idea, just need to remove the weld seem on the inside.

@DirtLifestyle Жыл бұрын

Interesting. I will go look at home depot today 👍

@Flitzer514 Жыл бұрын

Time for a lathe, Nate! A 12" or 13" would be nice.

@senorarnold Жыл бұрын

Aircraft Spruce and Specialty Co. sell seemless tubing in all different ODs and IDs by the foot. I did a quick check and they have 3/4 OD with a .620 ID slightly smaller than 5/8. Hope this helps.

@thumpstar12502 Жыл бұрын

I agree . then just buy a .625 carbide tip reamer and open it up if you have to .

@josephvavken3235 Жыл бұрын

McMaster Carr awesome website for random material, great job explaining everything. Really enjoy all the different builds. What’s going on with the tdi engine build?

@mattuebelacker1963 Жыл бұрын

Hey nate love what ur doing, for the sleeves how about some smaller diameter d.o.m tubing. That stuff is made very accurately but be sure on ur measurements bcuz that bushings u were holding up looked thicker than 1/16"/ side going off the 3/4 od and 5/8 id u mentioned! Goodluck bud!

@TheEinart Жыл бұрын

Love your work, i see also you have a hole in your hoodie, something familiar with that 😅

@muddiexj Жыл бұрын

Try McMaster Carr for the bushing material. They won't be cheap but if they have it you can buy it in various lengths depending on your needs and it ships quickly.

@TheMrhick92 Жыл бұрын

Maybe the sleeves for a set of leafspring bushings would work

@RealGumbyOfficial Жыл бұрын

McMaster carries a couple options that might work for the sleeves like 89495K185, 5/8 OD and .385 ID made of stainless steal… also there a couple spring rate calculator online that can help you determine the rate of any spring you have based on the length, thickness and number of coils etc. Cheers to the best mod in offroad: suspension🍺

@highcountrystories 9 күн бұрын

I think I heard you say you were going to drill that sleeve for a zert to grease your bushings.. not sure any way very nice build!!

@Jodah175 Жыл бұрын

Next tool on your xmas wish list: a small lathe. :-)

@kyles360 Жыл бұрын

Just used dirtlifestyle coupon at barns and saved $81.00 on my link kit for my samurai. Have you ever thought about making anti squat/roll information videos? You usually go into extreme detail on most things love your videos I believe I have watched every one by now. Keep it up Nate. 🤘🏾

@StormbornJKU Жыл бұрын

The amount of beef on that trailing arm just makes me believe that the frame side mount is going to rip right off. I’d suggest getting some mounts from Barnes and cutting the factory ones off and welding on some beefier ones.

@Steddywelly Жыл бұрын

Can you make a video on air suspension ? How it differs in suspension dynamics than a coil spring

@dandahermitseals5582 Жыл бұрын

When I was a kid lots of cars still had the drive shaft in a pipe with a tapered tubular on each side to eep the axle square. A big strong tubular triangle. Studebaker light trucks axles were like that. This is just a modern rendition of that original technique.

@Kami8705 Жыл бұрын

McMaster and find somebody with a lathe, would be a simple job

@PaulKaiser42 Жыл бұрын

I understand that you are going to strengthen the disco’s suspension with the trailing arms but (I likely missed this in your description) what are the additional benefits you get from them? When building my rig I always tried to consider building in lightness….this seems to be just the opposite 🤷🏻‍♂️

@johnyhawgleg Жыл бұрын

I used to work in a spring shop making custom leaf springs and repairing/replacing bushings. Get ahold of your local heavy truck/semi truck spring shop. If you are going to be greasing this you will want a hard brass/bronze bushing in the center of the neoprene outer bushing. That will have a really good long term wear quality without having to worry about the bolts seizing in the bushing.

@albertfetting736 Жыл бұрын

Go to an Ag store, tractor supply , John Deere, Kubota and ask for bushing sleeves for control on 3 pt hitches.

@Escape.Idiocracy Жыл бұрын

Maaaaaan I’m think the gladiator needs trailing arms too- like the hybrid high clearance kind.

@S_Stanley29 Жыл бұрын

For sleeping could check dirt king they have loads of builder parts

@talon0863 Жыл бұрын

Thanks Nate, I jumped on this topic. Can you get shock oil 30% more viscous than, I don't know what Bilsteins come with, if it were 7w then go to a 10w, etc.? IDK about Bilstein but Ive been doing this with dirtbike suspensions for decades.

@greghoffstadt667 Жыл бұрын

As always. Great video. Learn a hella metric ton from you. Side bar....... I don't mind reading the comintary. But, is there a way to change the text color to something a little easier to read. It's probably me. But, was curious.

@BradPickett685 Жыл бұрын

metal supermarkets for the bushing sleeve

@Offroadcowboy Жыл бұрын

Hi Nate, always enjoy your videos. If you still need the sleeves, I can fab them for you for the cost of material and shipping from Mount Vernon, WA. P.S. when are you going to get more XL t-shirts in?

@jamesvanhoose3132 Жыл бұрын

McMaster Carr had the tubing. .75 is. OD and 6.2 ID. You may need to drill out the center slightly I know. But it's the best place I can find without buying 100 feet of it. Also ruff stuff does custom bushed DOM. Maybe Barnes does too. I would with McMaster. Good luck.

@270Remi Жыл бұрын

1/2 sched 40 black iron pipe is about 3/4 od by 5/8 id

@CodyCrafted Жыл бұрын

And butter soft with an inconsistent wall thickness, and a seam.

@justincmw Жыл бұрын

Try McMaster for the sleeve

@simon-mouse8739 Жыл бұрын

Nate, are you using extended / Longer air bags or stock? They are now available in longer lengths in case you weren't aware 👍

@michaelkeefer1471 Жыл бұрын

I'm with Jeff, You need a lathe.

@jamesatkinson366 Жыл бұрын

Curious have you looked into UMHW? I forget the drawn out name but it's a hard plastic but can do some tricks when heated up. I work for a boat company in Helena Montana and we use it for a lot of motor mounts and oar locks on drift boats...side note I have a 2001 disco 2 that I'm trying to fix for the wife so she can have her own street/off-road "Jurassic Park" rig as she calls it. Your disco videos are big help! Keep the videos coming love your channel! Especially since I'm originally from the PNW!

@CodyCrafted Жыл бұрын

UHMW, aka: Delrin. Not really the right application for it.

@skyhook040 Жыл бұрын

I'm stretching my TJ to LJ length and pushing back my axle. What would you say would be the longest that you would make the control arms?

@lifelinefabllc Жыл бұрын

My suggestion is have a local fab shop just drill some 3/4" 4140 ground and polished shaft. I could do it and mail them but it would probably be cheaper and quicker if you have a relationship with a local fab shop. If you want me to do them let me know but I will have to go source the shaft as I don't have any that small.

@DirtLifestyle Жыл бұрын

I appreciate it! I think I have it handled now, but thanks again 👌

@jeremy8715 Жыл бұрын

Wouldn’t the extra weight below the frame help with balancing top heavy vehicles (and potentially off-camber situations)?

@DirtLifestyle Жыл бұрын

Kind of. It's half sprung and half unsprung. BUT it's below the roll over axis so it kind of helps lol.

@maximumoverland Жыл бұрын

Just saying, I think you be credited with building the ultimate Mid size truck movement… just look at your boys Muddy beards and Big tire 😂 you should feel good about that dude , Ian has been my fab legend for years and now you’re doing the same badass work. Congrats Dude 🎉! I gotta hit the trail with you one day 🤟🏼

@bosqueboys Жыл бұрын

What is that clamp setup on your evolution saw?

@M1ST3RHYDE Жыл бұрын

On ebay "steel tubing 3/4 5/8" under $20 with shipping from N.Carolina

@whereswadlow44 7 ай бұрын

Can these trailing arms be used on the front so that you can do front coil overs as well? Looking at doing something similar on my Disco2

@dalemcbride7299 Жыл бұрын

Happy Thanks Giving why not have the selves machined to your spec? rather than trying to buy them??

@mikeburris9856 Жыл бұрын

Did you try Prothane? I’ve had great luck with them in the past.

@vincentpoole7588 Жыл бұрын

Nate. One should've increased your D2a wheelbase from 100" to 108" if the plan was to run 42 inch tyres sir ! Is this going to reduce the weight of this rather hefty Land Rover D2a ? V.

@jacobstein7179 Жыл бұрын

Nate, do the springs have any writing on them? They are almost certainly RTE (formerly RoverTyme) springs. The rears are usually rated for about 440 lbs on the lift you have. If you have the numbers you can call and get the exact spring rate, it's just one guy.

@davesmith8936 Жыл бұрын

I'm confused. Will that stock airbag work without a coil around it for support? Seems to me that it will need something or it will just bow out to the side.

@dalemcwilliams8006 Жыл бұрын

For the bushing sleeves, why not just go to your local machinist and have them bore some 3/4 tool steel out.

@M1ST3RHYDE Жыл бұрын

There is a small chance I have some stainless material in that size. I'll have to check when I get home. If you are stuck I can overnight it.

@DirtLifestyle Жыл бұрын

Thank you for the offer man! I'm pretty sure I have it figured out now but again thanks!

@tracykooken2606 Ай бұрын

Am I wrong but they r not for a rig that does towing ???? Not to mention the added weight.

@rodneywhetlow1996 Жыл бұрын

McMaster carr will have that sleeve materiel

@ZuluComander Жыл бұрын

Found them on mcmastercarr but only up to 2 inch lengths

@toddr1124 Жыл бұрын

It sounds like you want the airbag ride, so how are you going to keep the coilover from influencing things, especially if it is sized to be independently capable? Are you going to pull the spring off of it so it's just a shock, and then be able to put the spring on if the airbag fails? If you run both systems in tandem, pretty sure that rear will be stiff as all get out.