DIY Arduino Nano Soldering Station V5

Рет қаралды 19,172

Жыл бұрын

DIY Arduino Nano Soldering Station V5. Hello everyone!. I made a new version of the T12 soldering station based on Arduino Nano, a few changes are made to the software, now it shows the PWM power level that the sation applyes to the tip, other chenges I made is that now everything is now smd components, basicaly I transfered all the components of the Arduino Nano and Mini360 to my pcb, unfortunaly I can not put all the components on a single board so I also used two boards on this version as well. The soldering station now can be powerd from a barrel jack connector and USB type C and I also included a mini USB to upload the firmware to the soldering station easily as you normaly do with Arduino, now I decided to use buttons instead of the rotary encoder and lastly I made a beautiful 3D printed case.
Link to original project of Stefan Wagner:
KZfaq video: • T12 Soldering Station ...
EasyEDA site: easyeda.com/wagiminator/z-sol...
Link to Software, Schematic, PCB and STL files:
drive.google.com/drive/folder...
Thanks for watching, if you like this video please Like, Share and Subscribe to suport my Channel !!
Support me on Patreon: patreon.com/user?u=17351593&u...

Пікірлер: 67

@vencislavvankov4897 Жыл бұрын

Congratulations! I think working with buttons on this little box is inconvenient. It's much better with Encoder. And as you have done it with SMD, the project now looks like that of Stefan Wagner.

@Stefanev Жыл бұрын

Great and beautiful work. Thanks! 👍💰

@HMProjects Жыл бұрын

Thanks!

@fajarsan329 10 ай бұрын

Wish it works with t210, Nice work anyway

@mrpiramidon7140 Жыл бұрын

v6 - leave encoder. on the button quick change save favorite T12 tips =) Thanks!!! use first version station, work fine!!!

@HMProjects Жыл бұрын

I don't think it will be a V6, that's the last version :). I leave it to everybody else to modify it further as they will.

@gustasvindziulis Жыл бұрын

@@HMProjects could you then share the editable pcb files so we could modify as we like

@user-fh9px6hn5n Жыл бұрын

RESPECT!!!👍

@Utkrant_Hingonekar Жыл бұрын

@@HMProjects Can you Please make a soldring station for hakko 907 ?

@HMProjects Жыл бұрын

@@Utkrant_Hingonekar I actually have one, but I have to find some time to make a video about it.

@deterdamel7380 6 ай бұрын

Nice work. But it seem that a least one button is to close to the GX-connector.

@nenebaez4145 Жыл бұрын

Hello excellent video, make a video of how to do those pcb board design

@sklepa Жыл бұрын

Nice work. I respect that self made two layer pcb's, and nano components transfer, instead of using plug in module. Im feeling it, because I just finished my own jbc station on sunday, and as I suspected it would be so much cheaper and faster just earning the money and buy the fucking thing xD. But anyway.

@sohanurrahman5859 11 ай бұрын

Pls add c210 tip option in this. So that,micro soldering can be done with this

@meddiys6171 9 ай бұрын

Excellent.

@nyeinchanzaw6936 Жыл бұрын

Great work!!!

@HMProjects Жыл бұрын

Thanks!

@sergioswiszcz6015 Жыл бұрын

Excelente work!

@HMProjects Жыл бұрын

Thanks!

@irmadion4904 4 ай бұрын

Hello, It is compatible with Weller RT series tips? Of course with a necessory cable for Welle RT-Tips 3.5mm Jack!

@3DprintRC 7 ай бұрын

Will you make any review video about V5.0 about this project?

@Utkrant_Hingonekar Жыл бұрын

Can you Please make a soldring station for hakko 907 ?

@moobdi3 Жыл бұрын

The next version you can use a rechargeable lithium batteries and using it as a portable soldering iron

@karimmoradi3607 18 күн бұрын

very good perfect ❤❤❤❤❤❤❤

@user-ur2bf4up8r Жыл бұрын

But could you add a power limit setting to the firmware? I have a jbc sting and on a weak power supply it goes into protection, when 80% of the power is set in the firmware, it works with any power supply. But I can't add it to the menu and I have to flash

@diybuilderde Жыл бұрын

do you have the bom file for the smd assembly ?

@minhsangdidong9080 Жыл бұрын

can you send me the circuit diagram of the soldering station to control the temperature for the goot RX80, or can your circuitry be used for the goot soldering tip?

@3DprintRC 7 ай бұрын

Can we do this project which you share in describtion video attachment files?

@hedi875 Жыл бұрын

Hi. Can i replace the LM358 by an MCP602 (less noisy) ? Thanks.

@HMProjects Жыл бұрын

Yes, of course you can. Actually is even better the MCP602 is rail to rail and it will provide more stable and accurate temperature measurement.

@svsv9 11 ай бұрын

What is your thinking if I decide to put a second Female Aviator socket for a second heat handler let say, a 2 Pole commute switch to activate "Line 1" or "Line2" Do you think I may damage it, I am working on a Dual soldering station, but I get lost to figure it out how make it digital, or automatically identification of the tip when is turned on.

@HMProjects 11 ай бұрын

By selecting one on the time it should work ( assuming that everything is wired correctly ) but if you put two tips in parallel at the same time it may damage it or it it not work correctly because you changing the heater resistance and the thermocouple resistance. The best way in my opinion is to make two of this soldering stations or the through hole version ( V4) and put both of them into a nice case, in this way you will have two displays, two independent control of the tips, one it can be in standby while working with the other one, you can set the temperature independently for each tip and so on. 😉

@svsv9 9 ай бұрын

@@HMProjects Thank you for early reply, I don't know why KZfaq does not inform me replies when I have to get them. So Mechanically it won't have a problem if I switch and wire correctly. I am thinking commuting the 4 wires from one GX4 to another GX4 aviator connector. Fancier the way you share two independent system one Power supply with double output is a big form factor because of the PSU. I will see it what it is better. There's a way I fallow you in some social network? I would like to share pictures about the station based on yours version. Have a great one.

@betaalyt3809 24 күн бұрын

What about the sleep mode(fixed or adjustable) & temperature calibration?

@HMProjects 23 күн бұрын

The sleep mode is adjustable from 1 to 30 min. and the calibration is done in 3 steps by adjusting the difference between temp. measured by the station and the real temp. which you have to measure it with a multimeter or a dedicated thermometer.

@betaalyt3809 23 күн бұрын

@@HMProjects thanks for the reply. I want to know that can I calibrate the temperature in menu options?

@betaalyt3809 23 күн бұрын

@@HMProjects you are amazing. great job man

@dhairyasoni7467 Жыл бұрын

Need analogue potentiometer for temperature set like previous version

@HMProjects Жыл бұрын

On the previous version I used rotary encoder not potentiometer. Anyway I wanted to make it a little bit different by using buttons.

@dhairyasoni7467 Жыл бұрын

@@HMProjects go it bro

@MuhammadOwaisKhan83 8 ай бұрын

C210/t210 tip support???

@svsv9 11 ай бұрын

At 320 degrees with 15.3 nominal voltage, what could be the load current? I am taking a look at Power supply deciding for a 24V and 3A 70 Watt Max.

@HMProjects 11 ай бұрын

I don't remember exactly the power consumption at 15 V, but I can tell for sure that 3 A power supply is more than enough.

@svsv9 9 ай бұрын

@@HMProjects thanks.

@d2yo1 8 ай бұрын

None PID ?

@naveentechs Ай бұрын

Please make V6 with Encoder

@HMProjects Ай бұрын

I have built V4 that uses rotary encoder, you'll find the video on my channel.

@mohammadhoutary1338 Жыл бұрын

Can you share your gerber pcb design for this version

@HMProjects Жыл бұрын

Everything you need is in the Iink in the video description.

@mohammadhoutary1338 Жыл бұрын

@@HMProjects thank you ❤️ , how much max the watts

@HMProjects Жыл бұрын

@@mohammadhoutary1338 The tips are rated for around 70W at maximum voltage 24V but I will not go so far, at least with this soldering station, 19V is the maximum voltage that I recommend and the power at this voltage level will be around 45W wich is more than enough.

@mrpiramidon7140 Жыл бұрын

@@mohammadhoutary1338 with netbook charger 19V 2.1A works fine (max temp, K tips, PID-mode)

@calinmoldoveanu6858 Жыл бұрын

@@HMProjects if I want to have 60W I must have 19 V at the input and 3,15 A ? Now the station maxim can deliver 2.36 A

@meax7180 5 ай бұрын

What is the max input voltage from dc jack?

@HMProjects 5 ай бұрын

24V, but I recommend to use 19V.

@meax7180 5 ай бұрын

Would it work with 16v?

@HMProjects 5 ай бұрын

@@meax7180 Yes it will work, it works even with a 12 V supply, but with lower voltage the heating time of the tip will be significantly longer. Make sure your power supply has an output current of 3A.