DIY BMW Hood Emblem Replacement. EASY!

Рет қаралды 190,690

3 жыл бұрын

I've seen many ways to remove the emblems and I've tried many methods. I'm good with any method that gets the job done without damaging the car or scratching the paint.
Part Number for hood emblem: 51 14 8 132 375
Part Number for emblem retainers: 51 14 1 807 495 (you will need 2 of these)
Find the correct part number for your BMW here: www.realoem.com/
Check out Jamie's Store!: ourwearhouse.com/collections/...
Did you learn something from this video? Consider Subscribing here: / inthefastlanewithjamie
---------------------------------------------------------------------------------------------------------------------
**Subscribe Here: / inthefastlanewithjamie
Jamie is the Owner of Elite Motor Works in Sarasota Florida, You can check out his business in the links below:
-TikTok: / elitemotorworks
-Elite Motor Works Website: www.elitemotorworks.net
-Elite Motor Works Instagram: / elitemotorworksfl
-Elite Motor Works Facebook: / benzandbmwrepair
-Elite Motor Works KZfaq Channel: / benzandbmwrepair

Пікірлер: 142

@SOCMMOB 2 жыл бұрын

For anyone wondering, that plastic strap is BMW Part# 69420-FU, $227 USD.

@nicolav9239 2 жыл бұрын

Thanks I just ordered one

@ralphrotten 2 жыл бұрын

lol

@MRAC91653 2 жыл бұрын

Bargain

@PrivateUser395 2 жыл бұрын

Is it a BMW authentic factory part or aftermarket?

@anahimahani9357 2 жыл бұрын

😂

@dylananthony5454 2 жыл бұрын

Never would have thought of this! Truly a master when it comes to preserving every aspect of the car, innovation starts with the simplest of solutions.

@NewToolTuesday 2 жыл бұрын

Zip tie always worked for me just like your strap method but you can grab it like a handle one good pull comes right up

@joeysplats3209 10 ай бұрын

Tried that one too and it was too tight. But thanks!

@predaR6 2 ай бұрын

Didn't work:(

@kevinmathews5465 2 жыл бұрын

Thanks, Jamie. I followed the instructions to the letter and had the old hood ornament off in about 2 minutes. Super helpful video!

@mro4ts457 2 жыл бұрын

Just 1? I got 5 in my neighborhood in 5 minutes 🙌

@thefunnybuddy4138 2 жыл бұрын

Jamie look what you've created 🤣

@johnversteeg1184 2 жыл бұрын

I use 2 drywall screws,drill them at 3 and 10 oclock. Not to deep just a little and pull on them. Works for me👍

@davidhalley9795 2 жыл бұрын

Nice video! I didn't have the clearance to slip that strap underneath. I could barely get the blue prying tool under but it worked eventually.

@shannon4968 5 ай бұрын

Doc, you are so gentle.❤

@illiyakuryakin3092 2 жыл бұрын

Nice video. The only thing I would do differently is after cleaning the area under the rondel, is apply a coat of sealant or wax. But I understand that was just a customer’s car.

@vikramejames Жыл бұрын

Absolutely brilliant, got the logo of my R1200GSA motocycle with ease, thank you @Jamie's Garage

@joeysplats3209 10 ай бұрын

Alrighty then! I had tried everything but a banding ribbon to take off that stubborn badge and just couldn't get under it. I was ready to Dremel it when I saw your method. It was a super tight fit and I had to use the thinner of two bands I had. I couldn't push the ribbon out the other side, but it was just high enough to get a plastic pry bar under it. The rest was cake. Thank you!

@StefanApweiler Жыл бұрын

Best solution to replace the BMW Logo! Thanks very much

@aydnsadi6804 2 жыл бұрын

Hi Jaime, thank you for your wonderful video. I have a problem. When I wanted to get out emblem unfortunately both pins are broken? How could I take out the pins? Thank you.

@ianatkinson8464 2 жыл бұрын

Great tips and advice😎👍

@rbemuscle6058 Жыл бұрын

Awesome man! Very clever 👌

@solomonshv 2 жыл бұрын

thanks a bunch. i'm going to try to put the classic badges on my 2021 X6.

@fredwooten14 4 ай бұрын

Great job! Very understandable video.

@DD-ng3bj 2 жыл бұрын

Was waiting to see a hammer 🔨 or ice pick at the finale but this must be a legitimate good working customer car 😅

@sustat86 Жыл бұрын

Great video, thanks!

@iwonaczapla2406 23 күн бұрын

I seriously twitched when that dude with screw driver was trying to remove it🤣🤣

@abdullahmalik9061 2 жыл бұрын

Great job💕👍🏻👍🏻

@joshredding9588 2 жыл бұрын

You seem a little OCD about paying attention to the details…I love it! Lol I’d like to work for you, I bet we would accomplish big things sir. I’m the same way. ;-)

@toly78 Жыл бұрын

Man, removing the badge with the screw driver just finished me :D :D :D

@cupidon197 2 жыл бұрын

Hi Jamie, can you make a video on how to replace the emblem on the steering wheel of BMW X3 2.0d F25 (Jan-2015)? Or just give some instructions on how to do it? Thanks a lot !!!

@yitzchakkatzir1547 Жыл бұрын

Having never done this before but just thinking out the box with the goal not to damage anything - is it not possible to superglue a "handle" to the center of the emblem and once stuck, pulling it stright up away from the bonnet it off carefully with contrrol force. It seems like it must just go straight up and out. Nothing else holding the pins. Would that work?

@petergondolier4088 2 жыл бұрын

Easiest way I found is using an empty 1L plastic yogourt, or cottage cheese container. Cut a 1 Inch wide circular strip from the container. Then making sure the natural curve of the plastic strip faces down feed it under the emblem, same as you did with the strap. The natural curve keeps the strip down against the hood so it will easily come out at the other end. Then just grab both ends and pull it straight up.

@chiefrocka8604 Жыл бұрын

I’m looking for the hack as it’s been 8 years since I did a eBay chinese Bmw badge swap out and I used a cloth wrapped around a butter knife and tbh I spotted your suggestion and that’s gotta be the easiest pushing under then pulling . Good tip 👍

@joeysplats3209 10 ай бұрын

Tried it. No go. Sweat dripping off my forehead, veins popping out... nothing. The banding ribbon I pulled off a box in my garage was thin and stiff enough to get under the badge and finish it off with a plastic pry bar. But it might work on one that's not so dang tight.

@gregpodmore2850 11 ай бұрын

Thanks Jamie.👍👍🏴󠁧󠁢󠁥󠁮󠁧󠁿🏴󠁧󠁢󠁥󠁮󠁧󠁿

@frankieb2220 Жыл бұрын

Brother,you Nailed that Video.Thanks for Tha FYI man.. 😎 👍 👌

@tperry88 2 жыл бұрын

Sucking up now after his last video 🤣✌️ hello from Scotland 🏴󠁧󠁢󠁳󠁣󠁴󠁿

@rogelioalbertoavilez Жыл бұрын

Maaaaaaaan you gave me a heart & anxiety attack on the first vehicle you scratched….. great video keep making more so I can keep my car in great shape and looking good

@TeeWag671 Жыл бұрын

I cringed so bad on that lol

@Dcs-Brasil 3 жыл бұрын

thx bro!

@608439021 3 ай бұрын

Thank you!!!

@Nipplator99999999999 2 жыл бұрын

I normally get it up a bit, and use mechanics old friend some piano wire, wrapped around the edge and pull it off via a slide hammer.

@bobsagetpiss 2 жыл бұрын

Man my heart sank on that one just full send on that hood lmao. I hope that was a throw away hood for that guy.

@rogergroover4971 2 жыл бұрын

Jaime , your hilarious, keep doing the videos! You make me want to find a very old BMW to work on. And by old I’m talking like 20-35 years old. Your opinion?

@kennethstephens8046 2 жыл бұрын

E34, e36, e38. E38 is kinda complicated though. But still great cars

@codyfield6859 2 жыл бұрын

Definitely look at an E46. Very inexpensive overall in my opinion and once you replace all the old plastic/rubber the M52 is a very reliable engine *Edit - M54 engine*

@kennethstephens8046 2 жыл бұрын

@@codyfield6859 I agree. Can’t believe I forgot to mention the e46. Guess I just like older stuff and the m20 and m50

@mhelmi73 3 ай бұрын

Thanks 🎉

@noboringconcrete 29 күн бұрын

Would it make it easier (once you get strap fed thru) to slide the strap closer to the pins (2 & 8 or 4&10 o'clock positions) & pull up from there? I'll try it in few & I'll let you know. Just got to order that $224 strap from bmw & hope it's not on back order 😊

@roninprime6080 Жыл бұрын

Used a ziptie instead, worked out fine

@T3MPL3TillIdIe Ай бұрын

What do you think about the 50th anniversary emblems ?? And where can I buy them . I just order a set of 7 for the price of 30 bucks. Too cheap to be good but like I said I just order them .

@xxqick-_-shotsxx5587 2 жыл бұрын

Watching you scrach the car with the flat head made me tense my hole body

@twenty1063 Жыл бұрын

I can’t believe you really did that 😅

@its_me_dave 9 ай бұрын

Packing strip, used to break into cars BITD. Happy days.

@luckyguy600 Жыл бұрын

I prefer the screwdriver method. Especially if you're in a really bad neighborhood! :)

@Laphoot 2 жыл бұрын

fishing line works for me

@04DetroitLS 3 ай бұрын

Any chance you know the size of the hole? (Aftermarket hood has marks for the hole but need correct size bit)

@dperkinson 13 күн бұрын

What if my new replacement doesn’t have pins on it? My VW bug is a 2004 and the old badge had pins, but the pins didn’t even line up with the holes. The new official VW badge only has a very strong adhesive on the back. Maybe that’s how they’re now doing it 20 years later.

@Mondaventure Жыл бұрын

How about 3D printing a curved edge tool?

@mariobianchi1909 10 ай бұрын

I followed this tutorial but in my case the new emblem doesnt seem to stay firmly on the longitudinal side.

@calebmange3991 2 жыл бұрын

I use zip ties to tie them to the vamos Solenoids in my m2 because theirs no room to pry them out so I tug them out

@calebmange3991 2 жыл бұрын

I also use atp 205 re seal fluid for all my w plastic and rubbers

@stevelawrence4705 Жыл бұрын

Thanks Jamie, very helpful regards Steve 😎

@dudndadn12212 2 жыл бұрын

How about one on the trunk lid??

@_BYAKKO_01 Жыл бұрын

Thanks 🙏 What is the size of the logo (mm)

@wojtech270 7 ай бұрын

good thing i saved theese straps from a package 3 years ago just in case

@JamiesGarage1 6 ай бұрын

Save everything! You never know

@Starry_Night_Sky7455 2 ай бұрын

@@JamiesGarage1 Ha ha, just keep on encouraging hoarding.

@Zechariah340 2 жыл бұрын

I've never owned luxury cars but I'm kinda intrigued to know how much a replacement BMW badge would cost 👀

@beckyferguson284 Жыл бұрын

I just bought one from a wreckers cost $30 NZD

@wolfythesunbro 9 ай бұрын

Front hood one is very cheap and easy. Back side one is like 5x times more expensive for some reason. I also think it's a pain to replace it too, not sure tho

@juniorwilkinson8968 2 жыл бұрын

Funniest video on the internet..😂😂

@MrEnwen 7 ай бұрын

Where to buy that X5logo and how much?

@colinhenman2420 2 жыл бұрын

Hey there. New subscriber. Question if that’s ok….own a 2016 X1…needs rear rotors/pads. I’m pretty mechanical but get differing options in regards to diy. Just wondering what your thoughts are on that. Thanks. 🇨🇦

@OliveGrummer 2 жыл бұрын

Probably need a scan tool to put the back brakes in service mode.

@rinx34 6 ай бұрын

One tip - put some grease on pins and grommets. I have sed vaseline. Do not harm plastic.

@eliudfidelgarciamarroquin1219 Жыл бұрын

❤❤

@heretic1132 4 ай бұрын

Imma start straling these and sell them for dirt cheap

@constantinak6648 Жыл бұрын

Where do you buy the strap?

@wolfythesunbro 9 ай бұрын

Please confirm that it was a joke. ... right?

@Starry_Night_Sky7455 2 ай бұрын

He must think that everyone accumulates these straps from mailing boxes he probably receives by the truckload at his garage, lol. I think buying the strap would be really wasteful. Of course, you want to find the "tool" he just improvised here. It is a cut piece from plastic box strapping. Buying it would mean you likely would have to get it in a large roll (Amazon has it) Perhaps get the roll then sell it in small easy mail strips for $20 each + shipping to everyone that watched the video thinking okay, I haven't ever saved those from the rare box wrapped with maybe two of those box strips I get delivered to my house from UPS or FedEx, lol! Maybe try some blue painter's tape to protect your car's paint and use something you might have like a plastic lid you can cut to use the thin lid top to slip under the emblem to lift it up. That might work too.

@blvkopvl5979 2 жыл бұрын

my jaw dropped to tha floor

@planecrazyish Жыл бұрын

👏👏👏👏👏👏👍

@SD_Racing 2 жыл бұрын

"… use any cleaner that's safe for the paint of the vehicle" - proceeds to scuff the paint to hell …

@FrankRemley 3 жыл бұрын

What do all of those numbers mean?

@crystalgentry3209 Жыл бұрын

Those numbers are from production associates showing there job was completed in the factory.

@instalai5823 Жыл бұрын

Is it safe to use any kind of tape?

@Doctor9Raccoon 5 ай бұрын

no use the weakest

@Starry_Night_Sky7455 2 ай бұрын

Use what is known as blue painters tape. Ask anyone in paint department at Home Depot. It's meant to not adhere to cured paint. 3M Scotch Blue 2090 Multi-Surface Painter's Tape. That should be safe.

@firozchouhan2693 26 күн бұрын

Where is the Volkswagen logo under the BMW

@ColombianMompi 2 жыл бұрын

Am i the only one who was expecting that thing to just POPout and hit him in the face? I also like the other method lol.

@Mondaventure Жыл бұрын

0:30 😱 triggered!!!!

@ricstanley8769 3 ай бұрын

The holes are completely different on my BMW 2 series.

@luc1f3r0_mf7 2 жыл бұрын

Some strong hot glue and yank

@tommyreusse3858 Жыл бұрын

0:40 ahh that gave me anxiety

@user-yf5xj8lu4y 8 ай бұрын

🙋❤

@shooflyshoo1754 2 жыл бұрын

I like your first method, it made me cringe!

@m0b127 Ай бұрын

Wtf did the dude on beginning 😂😂😂😂

@URLforme Жыл бұрын

Somebody stole mine

@lettucekat_ 8 ай бұрын

Almost grabbed a flat head 😅

@atakan888 2 жыл бұрын

If it is this hard for him then it is impossible for users.

@HeartFilledHatred 2 жыл бұрын

60 cents a piece and they are CHEAP?

@MahadsalmaSalma 2 жыл бұрын

👍

@nickmartinez5644 2 жыл бұрын

Only 60 cents? U sure thats a oem bmw part??

@edwardknox2213 2 жыл бұрын

A cheap bmw part?! That's impossible.

@Winblows999 Жыл бұрын

1st method is the only right way. id not recommend the 2nd method unless you want a roundel on your forehead 😂

@pleaseletitgo1818 8 ай бұрын

😂😂😂

@rinx34 6 ай бұрын

You have to pull emblem out PARALLEL, strip idea is not very good. Better work on one pin and another, slowly. But parallel is key!

@johnchen997 2 жыл бұрын

Lol

@nickmartinez5644 2 жыл бұрын

Lol "the right way"

@iiLoveAutumn Жыл бұрын

2:45 he's talking too much

@stuartmenziesfarrant 2 жыл бұрын

Its a bitch if the pins snap!

@orestruzic7596 Жыл бұрын

It’s disturbing how you ruin paint job with srewdriver just for fun.

@Se7nn 2 жыл бұрын

Please put a trigger warning next time on the “how not to do it” video. It was obvious what you were going to do, but no amount of prep time was sufficient to get through that segment safely. Perhaps it was intensified as my e93 is in the same black and I’m sitting in front of my car as you used that screwdriver.