DIY Composites Carbon Fibre Skinning

DIY Composites Carbon Fibre Skinning - How to tutorial

Рет қаралды 175,337

3 жыл бұрын

DIYCOMPOSITES.CO.UK
DIY Composites tutorial on completing the carbon fibre skinning / wrapping process to give non carbon fibre parts a genuine carbon fibre gloss finish that can be completed in a home workshop or business premises using our range of carbon fibre skinning materials.

Пікірлер: 70

@tamasbiro1766 2 жыл бұрын

Thanks for posting this! Well done!

@dhanashishwarpersadcarbonIsh Жыл бұрын

Very well explained 👏

@siliconvalleyengineer5875 Жыл бұрын

Fantastic presentation

@savadious 2 жыл бұрын

great guide. spot on

@AlejandroGarcia-so1gk Жыл бұрын

Perfect for my classic🔥

@aumoto10 2 жыл бұрын

nice and clear.. 🔥🔥

@rickythomas6678 3 жыл бұрын

If only it was as easy as the video What they dont tell you is That you will mess it up more times then not

@elusive7913 25 күн бұрын

skill issue. the video states to be meticulous.... not that hard.

@dieselburner4461 3 жыл бұрын

Make a tutorial how to cut the edges to nicely wrap around corners

@blood2chocolate403 Жыл бұрын

You forget the please....

@johnnyphase Жыл бұрын

how is the base coat resin different to the later applied resin? (except colour ofc), I have bought a supposedly full set for skinning but there is only one type of resin and hardener

@itolond 2 жыл бұрын

How does none handle parts that have countersunk recess for screws when skinning?

@kingkupal2567 2 жыл бұрын

What did you use for the brush to not getting hard after ung coat..?i hope u can help me..thank you

@THEBLCKR1 6 ай бұрын

what do you do when thr item is bigger then the roll? overlay it ?

@Dg-zj6jo 2 жыл бұрын

could you use this for foam wings

@ilanSniping 3 жыл бұрын

No clear coat ?

@KanjiasDev Ай бұрын

This (with maybe more then one layer) can also be used to repair cracks in most materials, right? I'm asking because I got a Canadian canoe which is made from plywood and my idea is to repair it with carbon fiber.

@defmud80 4 ай бұрын

What would be the added thickness to a skinned part using this process?

@Raminparvari-pv 5 ай бұрын

‏For the first time, I bought carbon fiber fabric and epoxy resin. Can I make the spoiler of my car carbon fiber? Please, someone who knows, tell me the simple steps of the work. I have seen a video on KZfaq. Where should I do it? How many times and how many layers should I apply epoxy after gluing the carbon fiber? And my spoiler has color, do I have to remove the color completely or is it enough to sand it so that scratches are created? Thank you for your help

@Dg-zj6jo 2 жыл бұрын

could you use a spray on glue instead of that black stuff please

@Jacob-rt6on Жыл бұрын

Would you need to remove the fake leather and foam on a center console arm rest to wrap that? Or do you wrap over it?

@johnmichaels4330 5 ай бұрын

Remove everything to skin it. Leave it there if making a mold.

@julianr5537 Жыл бұрын

Where can I buy the material?

@wtfftw24 2 жыл бұрын

I saw some small little pockets on the finish.

@civic2.2 2 жыл бұрын

Ware can I buy this kit

@davidhallowell9211 Жыл бұрын

What did you do with the taped back edges?

@MrScotsman12 8 ай бұрын

Cut them like it says in the video

@carlitomadrona6211 2 жыл бұрын

isn't it applicable to use avacuume bag on that work material?

@Theshadowcar 2 жыл бұрын

That's have different process... This is skinning...

@NuttyLlamasftw Жыл бұрын

Can I carbon skin over faux leather? The part I’m gonna do it’s not spongy at all. Might be able to rip the leather off

@h7opolo Жыл бұрын

sounds fine. how'd it go?

@ramonangeldelaguilaruiz4029 3 жыл бұрын

How BMW skin parts in what the call open pore carbon fiber? Is it possible to DIY?

@wrx2hot4u 2 жыл бұрын

what are you actually talking about “open pore carbon” ... eh

@itolond Жыл бұрын

Bit confued with what resins etc. i have GRP base to skin with CarbonFibre. do I use epoxy / VE RESIN or both?

@SL-ys8nx Жыл бұрын

Epoxy bro.....

@chrisstanford3652 2 жыл бұрын

🤗🤗

@slickrickdarula9483 Жыл бұрын

Where do you get the kit

@k3lloggzzracing577 Жыл бұрын

ebay sells different varieties

@moparrdudee87 Ай бұрын

So you left the part taped under ? Lol

@shaolin0071 3 жыл бұрын

Hello... in my opinion i would personally do this differently considering the part you are using it looked very smooth and with some light buffing and release compound you could have made a mould off this part by adding a few layers of carbon fiber and vacuum bag the part and infuse the resin and harder mix and the next day with some preparing of the mold you can same day lay your 1st part off that mould and infuse it for more parts and 80 % lighter or more in the end. I also recommend a spray Adhesive Like a product called Air Tac it takes seconds to apply ready for 1st layer of carbon and tacks well and less material 👌 also if you where not looking to make future parts and this is just 1 time part and only cosmetic you could just do your 1st layer or 2 and vacuum bag then that also means you need these things do that but if someone has a pump and know how to vacuum bag and infusion it much easier faster stronger to.. anyways just my thoughts. Thank you .

@justinbest9429 3 жыл бұрын

Hi, I have a diffuser that I want to skin, its already painted black so I'm thinking I could prep and lay the carbon straight over that.. am I correct?

@fonzeyontrack5212 3 жыл бұрын

@@justinbest9429 I'm wondering the same. I have a front splitter to skin and I'm a little nervous about the "one shot" attempt at laying onto the base tack. As my splitter is already CF (albeit damaged) I'm not worried about colour showing through, so wondering if I could just hold my carbon in place with tape/clamps and go straight to resin...

@micsmith806 2 жыл бұрын

The problem with not having a proper base is in direct sunlight the carbon layer can bubble up. Not sure how well anything other then resin will hold up

@tamasbiro1766 2 жыл бұрын

@@justinbest9429 no

@justinbest9429 2 жыл бұрын

Definitely can, I've already done it, prepped the diffuser, one simple coat of clear resin over the top and carbon straight over that. Super easy 👌🏻

@fsutoyo 2 жыл бұрын

disable tools plaese

@grantofat6438 Жыл бұрын

Stop saying that 200 g is extremely light. It is standard weight. Not even 80 g is extremely light.

@owenrook6467 5 ай бұрын

You guys didn’t even show the final product up close

@ttlcarbon 3 жыл бұрын

@Anony_mous1993 2 жыл бұрын

i personally think its way too much resin. from afar its too dark to even see the weave and up close its sooo shiny.

@jamie-ox8sg 4 ай бұрын

Why your just adding weight

@justinbest9429 3 жыл бұрын

It hurts my eyes watching this guy flat this component down using his fingers. A rubbing down block or the palm.of your hand will produce a far flatter effect. I have a diffuser I want to skin. The laying of the cabon fibre is very daunting.

@naspirit1551 3 жыл бұрын

its really not that hard if you have a second set of hands to hold the fabric up for you as you lay it down. Don't be afraid.

@justinbest9429 3 жыл бұрын

@@naspirit1551 I might just have to find someone I can trust to do that job, my next issue is, I did some measuring last night and my diffuser is bigger than I thought, I need to find some bigger impregnated carbon cloth otherwise I'm going to have joints everywhere 😑

@swealer Жыл бұрын

And don't forget: after wiping down the part with alcohol wipes, touch it with bare hands as much as possible😂

@darringrey4329 9 ай бұрын

Getting straight cuts that don't frey is no problem, use fiberglass tissue paper ,spray adhiesve on the carbon lay down the tissue press down let it dry then cut straight

@John--John 7 ай бұрын

@@darringrey4329no just pull out a single strand of carbon out the cloth then you have a straight line to follow and cut

@rocky6428 Жыл бұрын

A week to cover a part is ridiculous

@theedge5584 3 жыл бұрын

THE FAST&FAKE WAY OF DOING CARBON FIBER

@andrewparsons2178 2 жыл бұрын

Agree but i also will argue i have a 370z, i spent 1300usd for a carbon hood with poor fitment but a reputable company.... and it was heavier then my OEM hood LOL so the fact that someone could skin there OEM hood and have OEM fitment is a +1 plus people would never know because it's not a wrap :P so i sold the hood and i'm going to skin my OEM :)

@theedge5584 2 жыл бұрын

@@andrewparsons2178 Good point!

@jimmysmyth7510 3 ай бұрын

Just dont do this

@didiermejia780 2 ай бұрын

Why ?

@TylerDylan21 Жыл бұрын

Did you use clear coat at the end of the process? Isn’t 120 grit sand paper rough for this process??

@higherwrldsprodction2955 Жыл бұрын

If youre laying carbon just for appeal then you want a mechanical bond with the part to the resin. My understanding of skinning is using one layer to mold the carbon and then prying it off and enforcing the back for a 100% carbon piece. This process defeats the purpose of using carbon... if you are trying to make a full carbon piece either you want to create a mold OR polish the piece you want to make carbon from 800 grit to say 3000grit to polishing. Add release agents, lay down 1 or 2 layers then pry it off the part and enforce on the inside or back of the part.