DIY Driveway Gate Vehicle Detector Cut In Loop Installation

Рет қаралды 220,256

13 жыл бұрын

Gate Depot provides free technical assistance with all purchases. Not only great support. But great prices too! We carry the most comprehensive selection of driveway gates and automation products in the world. Call or click today: 1-888-818-4283 www.gatedepot.com

Пікірлер: 36

@windturbineclimber5412 5 жыл бұрын

This is kinda how traffic lights know you are there for the light to turn Green. The metal from your vehicle inducts a current into the wire by way of induction which has to do with the North and South Poles repelling each other through magnetism. It sends a signal to the traffic signal cabinet to tell the light that there is a vehicle there.

@lazerusmfh 3 ай бұрын

Radar is now used primarily instead of loops, in many dot programs in the us.

@OsamaAli80 8 жыл бұрын

i have the following question; what type of wire you are using for the loop? if i have existing gate barrier and i need to add only exit loop what i have to do exactly?

@ehinolamichael624 6 жыл бұрын

can i twist the cable manually, and what are the necessary materials to put in place to have an effective loop detector installation?

@waldenhouse 9 жыл бұрын

Excellent!

@raecross8872 4 жыл бұрын

Yep nice work

@JonTheChron 10 жыл бұрын

My company uses the same technique for commercial and industrical wire loops, we also prebuild loops in PVC conduit for new constructions.

@unalee6588 6 жыл бұрын

we have loop wire used for loop detector Emial:sales8@jutairfid.com

@johnmckenna2622 6 жыл бұрын

JonTheChron n

@AdrianMartinez-vu6yy 3 күн бұрын

Si el concreto donde se ranura para colocar los bucles tiene malla metálica, es viable la instalación?

@kamalsampath8804 10 жыл бұрын

tnnx...

@gasparo.j.m.7198 2 жыл бұрын

Greetings! I would like to know, to calculate the speed, from the signal sent by the central of inductive loops, is it used a microcontroller or is there a software for PC!? I will be grateful if you can give back..

@mikehoncho9448 7 жыл бұрын

What is the trick for keeping the twisted wire from coiling up when you take it off the drill?

@edkoga7321 7 жыл бұрын

Mike honcho ... Tie the end to a weight or have some hold it. Also twist the wire tight then when you remove it won't undo so much you need atleast 7 turn per foot .

@brian23ny 10 жыл бұрын

Shouldn't you test the loop before applying the sealer?

@AccessControlForum 10 жыл бұрын

Always test the loops inductance, easily done with an LCR, and at the very least insulation quality with a megohmmeter, sometimes called a Megger - from the brand name Megger, before you seal. Then document with a sharpie on the controlling device i.e. loop detector, gate operator, etc. Without a reference of the loops quality it may be time consuming to diagnose when faults occur and can help for warranty purposes. We recommend using backer rod (to allow the sealant to properly cure), BASF's SL1 sealant or Sika from Home Depot $12 a tube, and never splice the wire much less when its below grade. Overall this is a good representation of a quality loop install! Thanks for the video!

@zakialavi3468 7 жыл бұрын

hi there can you pls tell me which wire can we used for loop ? and how many wir rings do we needs inside the cut pls ?

@edkoga7321 7 жыл бұрын

zaki alavi depends on loop size Best to call detector manufacturer. But normally around 3 turns. The smaller the loop the more turns & v.v.. The type wire best is xlpe. also never bend wires @ 90 degrees, saw cut the corners @ 45.

@loyauteiron7754 6 жыл бұрын

Hi Guys, is it possible to use this inductive loop for traffic light?

@sromnatencze1649 5 жыл бұрын

Yes its possible

@edkoga7321 7 жыл бұрын

Another professional amateur Co.. If you want longevity for loops make saw cuts @ 45degrees. Wash your sawcuts and let dry. Dust prevents sealant from sticking! And they used thhn for many years b4 xlpe came along! Make sure you have atleast 7 turns per foot on your lead-in wires. Cuts should be 1-1/2 to 2 inches deep, lead-in cut should be if possible 1/4" wide for the twisted wire. Important: if wire insulation is cut thru to the wire you're gonna have troubles. Don't use it!

@unalee6588 6 жыл бұрын

Great , we are loop detector manufacture. Email:sales8@jutairfid.com WhatsApp:+8618179436123 Skype:una0305

@windturbineclimber5412 5 жыл бұрын

I agree

@renanteginolos7878 8 жыл бұрын

what will happen if we put two loops in one detector? is it ok if i use #14 THHN cable for the loop.

@panthertrentetrois7473 7 жыл бұрын

You can use this kind of detector to set 2 loops: www.in2access.co.uk/products/proloop-2-11-pin-base-2-relay

@shanek6582 6 жыл бұрын

What are these loops for? Do they tell you when someone is in your driveway?

@yorickhunt3371 6 жыл бұрын

Vehicle detectors.

@laneheer1172 6 жыл бұрын

How do I wire it into my mighty meal gate opener

@LIGIADZIEZIC 6 жыл бұрын

mighty wule sucks buddy !

@unalee6588 6 жыл бұрын

Send your inquiry to my email sales8@jutairfid.com. I can help you

@rubenmejia389 9 жыл бұрын

There are serious flaws in the way these people cut vehicle loops. -On asphalt, the cuts on the cuts on each side should not go at the way to the corner. - Just using a scraper is not a proper way to clean a slot, an air blower should be used. The sealant needs a clean surface in which to adhere to. - Splicing a loop lead-in is a HUGE and a HUGE no-no.