DIY How to attach crocodile (alligator) clips to a wire and make your own test leads

No video

DIY How to attach crocodile (alligator) clips to a wire and make your own test leads

Рет қаралды 95,417

Boris Dusnoki

Күн бұрын

Пікірлер: 32

@basvandersluis5662 7 жыл бұрын

Good tips! Especially the one with the screwdriver, because I'm always struggling to get the rubber piece back on while holding the clip itself. Thanks!

@dusnoki 7 жыл бұрын

Glad you liked it man :)

@snoshcat3627 5 жыл бұрын

I was looking how to do this and when I searched it up it came up so specifically!

@SuperMicroguy Жыл бұрын

Don't use nippers to get insulation off a wire! Use wire strippers. That's what they're made for.

@rokstr222ify Жыл бұрын

For anyone watching this trying to accomplish this task, don't follow this example, there's alot this guy did wrong, the crimp is supposed to go over the insulation of the wire, also his soldering technique was very incorrect, please find another video for better instructions

@hermanhermitz9101 6 жыл бұрын

You are supposed to crimp part of the wire that still has the insulation on. That's what the crimp is for.

@TravisTerrell 6 жыл бұрын

Yes! You are absolutely correct. The crimp is how the wire remains in place. It provides strain relief and removes some of the stress put on the solder when handled. Especially given how easily those tabs bent--they will lead to a weak joint, even if the cable is handled relatively carefully. You should slide the wire further up in, then solder to the clip, then close the clips over the insulation.

@tactical-bucket Жыл бұрын

The crimp is supposed to grab insulation and youll definitely get better soldering results by heating up mated parts before flowing solder.

@maineman152 2 жыл бұрын

Just my way but I always have soldered the wire to the clip then folded the tabs over and compressed them with pliers to make sure the clip was really secure and strong so the wire wouldn't accidentally pull out if you stretched the lead or knocked the meter off the bench,... like no one ever does that, right.

@nissankafernando3281 2 жыл бұрын

thank you for your help

@mikhailchyorny7275 2 жыл бұрын

Thanks. very helpful

@walshesworkshop 4 жыл бұрын

Thanks Boris. I bought a bag of these to make an electrolysis kit and didn’t know where to start with them. Can you apply heat to the sleeve afterwards, as it looks a little baggy?

@Saiz0x Ай бұрын

❤

@boldnbeautiful5093 4 жыл бұрын

Can I use it without soldering?

@ritchiecassidy9151 4 жыл бұрын

Cos

@dusnoki 4 жыл бұрын

Yeah of course

@sanjaycolaco 4 жыл бұрын

Thank you for this nice tip.

@shreyaskumar5366 Жыл бұрын

I never possible to solder the wire on the clip's metal Why anyone knows? Solder does not stick on that metal

@daminidesai1809 3 жыл бұрын

I was just thinking from where I should fix the cable's

@hafizdr 6 жыл бұрын

i have your same soldering iron

@dusnoki 6 жыл бұрын

It does the job... was the cheapest one I could find locally, needed it bad, my old one died :)

@sikksixxsinema_9078 3 жыл бұрын

What soldering iron?

@wally14331 3 жыл бұрын

If my alligator clip gets too dry and the plastic around it tends to crack,is there anything i can do to make the plastic return to it's normal elasticity or at least less dry? Thanks if someone read this :)

@bosesebi6685 Жыл бұрын

heat it up, a bit.

@cutemouse5519 7 жыл бұрын

what type of wire do i need

@dusnoki 7 жыл бұрын

depends on what kind of load you are going to push through the wires. The higher the amps and volts the heavier the wire... i usually don't use them for more than 30V 3A and this thin wire has stood up well for that power (90W)

@MicahJKelly 9 ай бұрын

I usually put a Gazelle in the Crocker's mouth. That gets him to open up right goodly yeah? Seriously though, this is TERRIBLE! Not what you said, but how you did everything! KZfaq chillrens should never be taught that doing anything with wire with your teeth is a good idea! Its a HORRIBLE IDEA!! One tool to drool them all!