DIY Indeflate - Was it worth it?

No video

DIY Indeflate - Was it worth it?

Рет қаралды 1,741

Күн бұрын

I show you the DIY Indeflate that I made to work with myl my XTM Air Compressor from BCF that tI installed into my 200 Series Toyota Landcruiser.
Support us on Patreon and have access to a heap of extra content from campsite locations, behind the scenes stuff and just general day to day photos and videos.
/ jebbreysjibberish
I make videos about real world problems, reviews, and my opinions on all things related to my hobbies. Four Wheel Driving, camping, modifying 4wd's and campers, HAM Radio, Technology, motorbikes and Jetskis.
If you like my content, have a look at some of the links below:
Check out my blog here: www.jebbreysjib...
Follow me on Instagram! / jebbreys.jibberish
Follow me on Facebook! / jebbreysjibberish
#staun #offroad #4wd #indeflate

Пікірлер: 15

@MrSteelAu Жыл бұрын

thank you for sharing, good job. i don't do 4x4 driving but i enjoyed your plumbing setup. you did a professional job

@steinjohansen3142 Жыл бұрын

Osram has a battery powered small de-/ in-flator w/digital display and upto 4 presets memory w/autostop 7x7x17 cm, 640g

@billroach2393 Жыл бұрын

Good video mate. I still use one of the ARB quick deflator gadgets. Just a bit of a warning regarding the use of the type of unit you have cobbled together if I may. It is pretty much essential that you are located on level, flat (ie not on a rock) ground. If you are on uneven ground or have one tyre sitting on a large rock etc, the pressures won't actually equalise. The tyre on the lower side will have more weight resting on it and you will end up with non equal pressures when you drive off.

@JebbreysJibberish Жыл бұрын

So that would be the same issue with the mainstream brands of those too? I’ll have to do a test and see. I would have thought they’d equalise either way but now you’ve got me thinking. Would be an interesting experiment to see if it varies and how much if it does.

@billroach2393 Жыл бұрын

@@JebbreysJibberish a good experiment you could perform in your flat driveway would be to drive one tyre, say front right, up onto a hammer handle or similar 2" x 2" piece of timber. Now add your two fittings to the right and left tyres to allow them to equalise. Then, drive the vehicle off the timber and check the pressures. I'd guess they'd be marginally different. For a more extreme experiment.....jack one tyre completely off the ground and repeat the exercise. The difference between the two tyres will be significant once they are both back on the ground.

@and7976 Жыл бұрын

Apex quick deflators are the fastest for deflation hands down. They are expensive but they are the fastest and easiest way to deflate a tire.

@ashleydowding7655 Жыл бұрын

While not cheap, an ARB Twin compressor with pressure control and indeflate you don't need anything else. Pressures preset on phone no need to be checking pressure constantly.

@williambennett6526 Жыл бұрын

but far from bang for buck which this is.

@v8greg79 Жыл бұрын

Should you have a little tap on each hose as well so that when you are disconnecting, you can close each tap off so you don't lose pressure from one tyre while you move from tyre to tyre when you take the hoses off the tyre valves.? You'll have one tyre at 50psi and the other at 48psi by the time it takes you to fully disconnect.

@JebbreysJibberish Жыл бұрын

If I disconnect the other way around it actually works better. Because the Nitto fitting is blocked, so I just have to disconnect the nitto end first.