DIY transducer mounting plate-CHEAP!

Рет қаралды 257,280

Bill de Varennes

9 жыл бұрын

Simple way to mount your transducer without having to drill holes in your boat!

Пікірлер: 110

@johnbasiglone1219 5 ай бұрын

Nice job Bill. You did a fine job of solving that problem.

@Winchestersxp 6 жыл бұрын

Good tip on where to buy a thick piece of plastic..I have same problem last owner didn't know what he was doing mounted it too low with no room for adjustment..

@firstlast4100 11 ай бұрын

I have done this on 6 boats so far with no issues. :3/4 “PVC Trim Board :Scuff up board and transom : wipe both surfaces down w/ acetone / alcohol : apply LocTite PL Premium 3X adhesive ( Home Cheapo $8 ) : apply blue painters tape to hold block for adhesive dry overnight

@jbdba01 6 жыл бұрын

FWIW - you could countersink the screws from the original holes, get the screws flush or just below the transom, and then 5200 over the screws themselves. No need to drill into the board itself and measure where holes are...I'm planning on doing the board install as you recommended.

@grace2258 2 жыл бұрын

Or why not use the screws to help secure the new mounting block. Countersink them into the new block and you accomplish both tasks.

@paulclay1746 5 жыл бұрын

Sound advice, thank you

@dhudy26 Жыл бұрын

Thanks for the video. I plan on doing the same thing. Would be great if you could link to the exact 3M adhesive and trim board you used... I see other videos with very similar material (and 3M 5200) that fell off after a while... You seem to have the right combination of prep and material. Also wondering how much 3M was needed... i.e. 1oz, 3oz, or what. Thanks again!

@thumperphilbert 7 жыл бұрын

Brilliant!

@thediycrab2674 6 жыл бұрын

Cool! Simple and cheap

@ninjagodzilla6402 Жыл бұрын

Thats crazy!!!! Im doing the exzact same thing!!! With the exzact same poly board lol.

@hapaboy65m87 Жыл бұрын

im going to try that, thank you

@toddlester9843 3 жыл бұрын

Hey how has this plate held up? Looks like you made this 5 years ago. Thanks!!!

@03bonneville 8 жыл бұрын

Nice job

@billdevarennes9954 8 жыл бұрын

Thanks!

@NinoSpinner Жыл бұрын

hello what material did you use as a base where to screw the transducer probe?

@frankletizia7835 5 жыл бұрын

I used silicon white . As that just is good is marine ? It is water proof . I would after put off another day to get the marine sealer.

@newyota1 8 жыл бұрын

Good idea.I had some of that long before I needed it and got rid of it.It's cheap if you have a scrap piece, not if you need to buy a 16 foot piece

@billdevarennes9954 8 жыл бұрын

true enough!

@AN-kg4ei 2 жыл бұрын

curious now that you've had this on for many years... did the UV break down the PVC or 5200 adhesive let go off the PVC????? I'm very close to doing the same.

@thomasswiader2330 4 жыл бұрын

It's been a few years later. How is it holding up?

@hometownguy7184 7 жыл бұрын

a 10 dollar poly cutting board from walmart will do the same thing

@damonalagich4524 4 жыл бұрын

nylon ??? I would be using ABS and a methyl acrylate glue, same as what they use to bond the deck to the hull in boat building- never come off.

@Askeyb2011 6 жыл бұрын

So did the 3M Marine Sealant keep the mounting plate on the boat? I did the same thing on our boat. Haven't had it out yet but it has been two months since I glued the plate and mounted the transducer. The glue should be as good as it will ever be.

@TheSternSaver 9 жыл бұрын

Bill, have you looked into the Stern Saver glue on transducer mounting system? It's a commercially available version of this that is made from high density polyethylene, StarBoard and installs in ten minutes or less.

@MattTigers 8 жыл бұрын

We picked up a sternsaver, but there wasn't anyway to mount it on our stepped transom.

@AN-kg4ei 2 жыл бұрын

love the idea and thought about similar with the family cutting board... I think level mounting with bottom of boat may cause heartache if you go over something. I've always heard 1/4 - 1/2" above to save the day.... yes... I know this is 6yrs old now but thought it might save someone's wallet.

@williamriley2528 5 жыл бұрын

I hope those (3) transom screws were stainless steel... And yes, 3M 5200 marine adhesive/sealant is virtually permanent after a 72 hour cure or so...

@moonpiespotlight4759 7 жыл бұрын

The hoose! Must be a moose loose!

@biggtorquay6132 7 жыл бұрын

nice job...but if you had taken bolt out of mount before hand, rotated mount 90° surely this would have given you enough lift and still use existing holes? Nice vid none the less ;-)

@herewegofans 5 жыл бұрын

I was thinking same thing. 5200 the old bolts and bamm. But he did a good job. I make similar for my boats and friends boats, but when I mount I put two hex bolts glued and screwed with 5200 under board in counter sunk holes. And I crosscut the hex bolts for added grip. Buddy has fountain with trips and hasn't shaken loose yet lol so think it's safe for all. Also run the board on table saw set at 25 degree through horizontal axis several times to give some bite. But the trim already has so gonna play with next time someone asks for help.

@robford41984 8 жыл бұрын

So it's been about a little less than a year since you have mounted this, I bought a cabelas version (got it for like $10) and also got the 3m marine adhesive, the transducer on my boat was mounted wrong, and I am replacing the whole setup anyways. The cabelas version comes with 2 screws to mount it, how did yours hold up over the past year with just the adhesive?

@billdevarennes9954 8 жыл бұрын

+Robert Ford It has held up great! After letting it harden for about 48 hrs before putting the boat in the water, I haven't had any issue with it at all. Definitely better than drilling holes in your hull!

@oregonlife 5 жыл бұрын

Is the sealant that strong? You didn't have to drill any holes to hold that plate?

@loganvick3385 3 жыл бұрын

Nope in another comment 2 years ago he said that it has held up fine for the past 3 years

@davidkoba 4 жыл бұрын

depending on how rough you run your boat the plastic doesn't bond well with anything except silicone. i had to find out the hard way lol.

@robertryan7978 7 жыл бұрын

it should be 12" off center from center of prop

@Jay-un2zc 5 жыл бұрын

How thick is this board?Great video thank you for uploading.

@ninomigliazza1876 5 жыл бұрын

@The MBP it's about a half inch thick per video at 1:27

@josepeixoto3384 2 жыл бұрын

the ideal is 5/8 to 3/4 inch

@thomasbowman1604 2 жыл бұрын

Bill when you put the 3m Adhesive on the plate did you smear it all over or did you run lines across it and near the edges ? I,m thinking of putting 2 screws with (adhesive on them) from in side the boat in to the plate thru 2 of the holes in the boat already. I think this was a great idea and I just happen to have some plastic trim. thanks tommy

@billdevarennes9954 2 жыл бұрын

I spread it evenly over the entire surface of the plate. No screws. Has held up great.

@thomasbowman1604 2 жыл бұрын

@@billdevarennes9954 Thanks for the info.

@AN-kg4ei 2 жыл бұрын

that's exactly what I was going to do with one exception - recess bolt holes on back of pcv so that I can bolt the transducers down VS relying on screws.... I also thought about stealing a cutting board from the kitchen under the guise of darkness...

@scottjosephbrandt6175 7 жыл бұрын

Which epoxy did you use? Has your project held up to date? Or, has your project failed? I am planning on doing the same exact thing. I also have an aluminum boats and would like to add a different transducer mount. This was a brilliant idea you came up with. Thanks in advance

@billdevarennes9954 7 жыл бұрын

I just picked up a tube of 3M Marine epoxy at my local hardware store. It has held up great! 2 years and hasn't given me any trouble at all.

@scottjosephbrandt6175 7 жыл бұрын

Bill de Varennes Did you cover the entire mating surface of the wood grain, then apply it to the transom? This is definitely a great idea you had. I'd like to try it myself. The video was very informative!!!

@billdevarennes9954 7 жыл бұрын

yeah-I made sure to thoroughly clean both the hull and the block first. Then covered the block, leaving about 1/8th of an inch from edge so it wouldn't squirt out when I pressed it to the hull. Finished it off with a little caulking around the edge after it was dry.

@scottjosephbrandt6175 7 жыл бұрын

Bill de Varennes Sounds great! I'm going to LOWES in the morning to pick up those supplies. I'm confident that your procedure will work. I'm planning on getting a Humminbird Helix 7 SI GPS G2. I've researched the transducer mount on that new unit and unfortunately, it won't line up with my existing mount. Therefore, I came across your video and I thought it was absolutely a brilliant idea. I've got plenty of time for the 3M marine epoxy to cure. So, I'm eager to see my end result. I'm ordering the Humminbird Helix 7 SI GPS G2 tomorrow or Monday. Installation should be completed by next Saturday. Thanks for your video!!! It is certainly a tremendous help.

@billdevarennes9954 7 жыл бұрын

I hope it works out for you- like I said before, 2 years and not a single issue with mine. Still solid!

@FranksDIY Жыл бұрын

I know it's been a spell but how did that hold out for you

@asfltcwby 6 жыл бұрын

Nice idea...but if you're mounting the poly to the transom with epoxy why not just epoxy the xducer mount straight to the transom?

@miguelgarcia1025 6 жыл бұрын

the benefit of the block is that if you ever change transducer or need to move it slightly, you can re-drill (into the block) and move around the block or add other items without drilling more and more holes in the transom. If you mount a block first, you can upgrade electronics or fiddle with locations without ever touching actual transom again.

@kevinhermi9861 4 жыл бұрын

And more glued space will hold better

@billdevarennes9954 9 жыл бұрын

I did look at commercially available versions, but found the pricing to be rather excessive for what they consisted of. I'm sure it's a very good product-I just wanted to show boaters on a budget, how easily one could be made for just a few dollars.

@Askeyb2011 6 жыл бұрын

I bought a mounting plate from Cabela's. It is 12" long fair price. The only problem I had was the stainless screws that come with the transducer are 3/4" so I had to get 1/2" stainless screws to mount the transducer.

@mikebarb86 5 жыл бұрын

Thanks for the video! I have a question though does this pvc seriously stick with 5200 marine adhesive and thats it?

@jimfacteau4553 5 жыл бұрын

yes, but a stainless steel screw on each side is a wise idea

@FLYGUY5100 11 ай бұрын

How is this holding up?

@octico 6 жыл бұрын

Thanks for sharing ... eh :)

@MattTigers 8 жыл бұрын

We were going to use your method an got the materials together, but the 5200 says its not for use on PVC. Its concerning to the point of returning everything and buying a Sternsaver kit (starboard, and epoxy). I hope your good luck with the mount continues, but I'd keep a close eye on it!!

@billdevarennes9954 8 жыл бұрын

+Matt Beeramid I don't remember seeing that it wasn't recommended for PVC, but ran the boat the entire season last year with no issues-still rock solid! Thanks for the heads-up! I'll let you know if I lose it!

@MattTigers 8 жыл бұрын

+Bill de Varennes We got one of the stern saver things, but it's not going to work for us due to the stepped transom design. Really don't want to drill, but looks like it's in the cards.

@TriodeLuvr 4 жыл бұрын

I'm confused about the adhesive you used. The video mentions epoxy, but later you show a tube of 3M 5200. That's not epoxy, is it? I haven't used it, but would guess it's a variation of silicone adhesive.

@billdevarennes9954 4 жыл бұрын

it is 3M 5200 marine adhesive. I probably said epoxy, but you're right-it's not.

@lboutdoors5070 5 жыл бұрын

After you Epoxy the plate to the boat. Did u drill little screws into the plate to hold the transducer or did u epoxy the transducer to the plate?

@billdevarennes9954 5 жыл бұрын

yes, I drilled pilot holes in the plate first-then mounted the transducer with screws.

@josepeixoto3384 2 жыл бұрын

Transducer bottom surface should be 1/8 th to 1/4 inch *BELOW* the boat bottom, do your calculations on your boat. edit: and the vertical C/L square with the surface of the water; and boats in trailers are not always level...

@sstatic6093 3 жыл бұрын

$40? for a piece of board got to be something else that can be used right that serve the same purpose right?

@dmcwhorter9974 3 жыл бұрын

These boards are 8 dollars for a 10ft section- not sure you’re looking at the right board.

@pimpshack81 5 жыл бұрын

Will that sealant work on aluminum boats?

@billdevarennes9954 5 жыл бұрын

The boat in the video is aluminum. Painted with marine white. Sealant still holding strong-no issues at all!

@tripcia2524 3 жыл бұрын

ola , of what material is this white plate ?? Is it pvc ?? Thanks

@GusgusA1 3 жыл бұрын

starboard

@TN-Vols-Fan 3 жыл бұрын

Hey Bill, It's been six years since you posted this. How's it holding up?

@billdevarennes9954 3 жыл бұрын

It’s as solid as the day I installed it! Never had an issue with it at all.

@TN-Vols-Fan 3 жыл бұрын

@@billdevarennes9954 Thank you for the fast reply Bill. I'm going to do the same thing on my rig. Previous owner installed the transducer too low and directly behind a chine. I bought new Garmin's and will duplicate your project on my transom.

@Th3mast3r69 8 жыл бұрын

very bad location for the ducer. why would you mount it directly inline with your tariler bunk where it will most likely break?

@billdevarennes9954 8 жыл бұрын

+YouWrasse IsMine (th3master69) The plate is mounted above the lower edge of the hull so as not to contact the bunk during loading/unloading. The transducer bracket, along with the depth of the plate position the transducer about 3 inches ahead of the bunk. It is close, but unless I hit my trailer at 20 mph and drive the winch through the bow...it won't hit. I've had it on for 2 years and trailer the boat for every use, so have loaded and unloaded many times without a hitch.

@hbrookes 8 жыл бұрын

by the time it hits bunk boat is beatup on front anyway..should only go until it hits front roller?

@billdevarennes9954 8 жыл бұрын

Exactly! If the transducer ever contacts the bunk, I've got much bigger problems than just a broken transducer! Unless I cave the bow of the boat in or run over the roller, the transducer won't touch the bunk.

@Th3mast3r69 8 жыл бұрын

+Bill de Varennes its a bad place for the ducer period especially since you could easily have put it anywhere. If you look at professional installs, youll see that they all tell you to never mount it infront of any bunks. its a bad idea period.

@Th3mast3r69 8 жыл бұрын

but its your boat

@hbrookes 8 жыл бұрын

Home depot only has 16 foot lengths..wanna sell me a 6" piece?....lol Nice work!

@billdevarennes9954 8 жыл бұрын

I'll look around and see if I've got anymore-I'll let you know

@hbrookes 8 жыл бұрын

I was just kidding, but thanks for the idea..I will locate a small piece...:-)

@mickey52149 2 жыл бұрын

Thank you , not wanting to drill holes in my boat

@terrybarrett5522 6 жыл бұрын

Marine silicone would hold that mounting plate on with no screws at all, mine is 13 yrs and no issue

@billdevarennes9954 6 жыл бұрын

The plate is only held with silicone...only screws are the ones mounting the transducer mount to the plate.

@jokrazy2002 6 жыл бұрын

Silicone is better than 5200 marine sealant ?

@billdevarennes9954 6 жыл бұрын

I used 3M 5200 marine sealant-have had no issues since I mounted it, spring of 2015. 3 seasons of fishing and still as stable as day 1.

@jbettss 6 жыл бұрын

What kind of Marine sealant?

@notafuckinpplperson8233 5 жыл бұрын

jbettss 3M 5200 ya bozo

@mcplutt 4 жыл бұрын

Why would anyone put screws in the holes. Epoxy does the same job without screws.

@cameronm2203 3 жыл бұрын

you are going to wack your transducer on your bunk dude, be careful

@jamesbass3828 5 жыл бұрын

Plastic Cutting board from Wal-Mart lots cheaper.

@williamriley2528 5 жыл бұрын

An 8-foot length of that exact PVC trim at Menards is about $10 to $12... That's enough material to make 16 of those transom mounting blocks...! (He said about a dollar)...

@drdoutdoors1603 4 жыл бұрын

Does Walmart sell half inch or three quarter inch thick cutting boards? Anything less than half inch won't work.

@damonalagich4524 4 жыл бұрын

Why would you put screws back in the old holes? he had the epoxy to glue it on, why not over size the hole and fill it? omg! why not fit nylock nuts in the plastic for mounting the transducer- could melt them in......lots of room for improvement in this effort.