Converting a Car Alternator to Produce Free Energy

Рет қаралды 770,020

2 жыл бұрын

$2 for 1-4 Layer PCBs,Get Free SMT Coupons here:jlcpcb.com/IYB
Get free 18$ coupon:jlcpcb.com/IDK
Support us on Patreon: / diyking
In this DIY project video we are going convert a car alternator to a permanent magnet alternator.
In the previous project we built a wind turbine out of a truck alternator. Not a big sucess as these alternators are not made to work at slow speed. One of the soultion we though of is to replace the traditional rotors with permanent magnet one as they not only need energy to magnetize but envolves a bunch of inefficient components like carbon brushes and slip rings.
So in this project video we are going to conver a 12v car alternator into a permanent alternator to act as a generator or a powerful brushless motor, time to find out so lets get started.
More information about the material and designs visit the instructables article:
www.instructables.com/Convert...
Regards,
DIY King

Пікірлер: 296

@MakerFabio 2 жыл бұрын

Hi, thanks for sharing. I also have high power at no load on my conversion, even with original rotor. I have 200w at 24V. Tested with 2 esc , same result. I will test also another alternator

@petersimms4982 2 жыл бұрын

Brilliant video! Reminds me when I was at school . Propper problem solving a natural way to common sense :)

@noahgilbert8630 2 жыл бұрын

I love smart and creative people , thank you guys 👍❤️

@daniel0191bg 2 жыл бұрын

Nice video! Reduce the battery voltage if you want to decrease losses, the stator windings of an alternator are designed to operate at high currents / low voltages if you use high voltages you will need to increase the frequency in the inverter to increase the speed and thus the back emf. If the inverter does not reach such high frequencies all you are doing is waste the energy heating the windings. So you can add a higher load to increase efficiency using high voltage or if you want to run the motor with no load you need to decrease voltage to increase efficiency.

@DIYKingSaM 2 жыл бұрын

Will try that as well, seem like a good idea.

@berndscheffler9437 2 жыл бұрын

There is free energy and free energy generators. Yours aren't working. For your personal use and not for commercial purposes, you can build one that is located at the national patent office in Alexandria, Virginia or at international patent offices in Paris, France or in Geneva, Switzerland. With the deep state practically expropriated, there is no longer any need to fear that they will come in with hired killers and take you off. Do your own research.

@hasuo9749 2 жыл бұрын

@@DIYKingSaM Answear should be : I will try, thank you.

@Mix-gu4fb Жыл бұрын

@@DIYKingSaM hi, i already test and see the efficiency problem you need to change the coils wiring to star not delta wiring

@Mix-gu4fb Жыл бұрын

@@DIYKingSaM even if you use higher frequency you will face skin effect problem (your alternator coils are 1 solid wire not multi thin wires )your coils will not handle the high current and will heat up change the wiring to star wiring

@ejirokporon5942 2 жыл бұрын

OMG, you guyz are just genius using those neodymuin magnets from the hoverboard motors was just pure genius. you literally just solved a mental block problem I've been having for over three months. thanks Guyz, great video great build. keep it coming

@berndscheffler9437 2 жыл бұрын

@paulsmith1981 2 жыл бұрын

Newtons third law of motion is the reason its doesn't work. The north and south poles of a magnet are of equal strength. Think about it.

@MrSexyskyrim 2 жыл бұрын

@@paulsmith1981 could a magnet be applied elsewhere to negate the pull between the poles?

@Flea-Flicker Жыл бұрын

OMG you are a bot!!! Right? The only thing that is genius about these Indians is they have mastered the method of duping stupid people. The law of conservation of energy states that energy can neither be created nor destroyed - only converted from one form of energy to another. This means that a system always has the same amount of energy, unless it's added from the outside.

@ejirokporon5942 Жыл бұрын

@@Flea-Flicker Did u watch the video before commenting?

@dandil 2 жыл бұрын

there IS a load on the motor: the propeller. it is doing work to move air and thus draws power, even if it is stationary. This explains the RPM as well: if you were running at no load then you would be close (ignoring internal motor friction/losses) to the max RPM, but because torque is being applied to the motor you need high current in the winding so the RPM (and back EMF) has to reduce to allow for the current.

@kingcosworth2643 2 жыл бұрын

I think the main problem is their rotor design. With low magnetic coupling, back emf is low so current is high. Plus it been an all steel 'ring' the induced magnetic field in the rotor will be doing all sorts of unwanted things. The motors in the Tesla's are a full induction motor with no magnets in the rotor, the specific shape of the steel rotor gets an induced magnetic field in it which becomes the repulsive magnet, quite clever actually.

@MrRao20 2 жыл бұрын

Great effort

@shammock112 2 жыл бұрын

I've been watching a lot of DIY Car Alternator Conversions and you guys beat them all hands down. You have a very professional approach and way better tools. I just subscribed to your channel and I hope you do a follow-up video on the problems you encountered with this conversion project.

@freeenergytransformer5842 Жыл бұрын

Converting a car alternator to produce free energy is not entirely free. The free energy must be a collapsing Ether field producing electrical transients. Turning car generators into windmills is not entirely free either. However, the cost of converting a car alternator to produce free energy is very low, and the benefits are great.

@peters9929 2 жыл бұрын

good work guys full respect

@interet-sanginteressant1756 2 жыл бұрын

I've been waiting for this ! Thanks guys

@THEOGGUNSHOW 2 жыл бұрын

Terrific repurposing project and documentation!

@dieselphiend 2 жыл бұрын

Very good editing and narration, well done!

@thinkforyourself2109 2 жыл бұрын

A lot of people talk about environmentalism, but you guys are actually making it happen. Good channel!

@faizanrao3574 2 жыл бұрын

Great job. Wish u all the best for next project.

@norbertkleespie6649 2 жыл бұрын

You do a very very important job guys!

@davidgood5390 3 ай бұрын

Great video with encouragement of modernum engineers

@philpique3187 2 жыл бұрын

Really interesting -I am learning a lot from this video!

@ViaAvione 2 жыл бұрын

Amazing! Thank you for sharing!

@samsungtvset3398 Жыл бұрын

For a permanent magnet synchronous motor the ideal supply voltage at any given rpm will be about the same voltage as what the motor would generate if spun at that same rpm. At the ideal voltage the motor current will be in phase with the voltage and the power factor will be highest and the current draw the lowest.

@markeverson5849 2 жыл бұрын

Great job very impressive thank you from the USA Ozarks

@eone2345 2 жыл бұрын

I suggest to paint bright color stripe at the tip of the propeller for safety reason, just like how an aircraft propeller works.

@electronic7979 2 жыл бұрын

Excellent project 👍

@renstarfilm3677 2 жыл бұрын

Fantastic Job my friend

@TeomanOzsen 2 жыл бұрын

I love this kind of environment friendly projects.

@DIYwithBatteries 2 жыл бұрын

Well made Dude really great

@one1onetime935 2 жыл бұрын

I wish I had friends like you guys!

@user-td8jv6iw4n 2 жыл бұрын

عمل قمة الروعة فعلن تحية من العراق

@akashchaudhari6631 2 жыл бұрын

Great work bros. Love from India 🇮🇳

@BigmoRivera Жыл бұрын

Great Job Guys 🤓👍🏽Good Luck!!

@murraychadwick9362 Жыл бұрын

Thank you very much for sharing your video👍

2 жыл бұрын

You are making so many nice things

@MrAdamNTProtester Жыл бұрын

YOU da Man! Thanks Happy trails

@ryanderek8125 2 жыл бұрын

These guys are great

@bendaves77 2 жыл бұрын

The systems I've seen built in off grid living here in America the alternator is placed below the blade system and has a large flywheel and connected via a belt

@bobbyshaftoe45 2 жыл бұрын

These guys just ROCK :-)))

@steffenwolffe507 2 жыл бұрын

how do you keep the heat generated by the rotor spinning (friction w/air) from decreasing the magnets magnetic force. You heat magnets up, the become junk metal, so.... Also, the glue has a temp limit as well. There's got to be heat there from eddy current as well?

@johnphilip393 Жыл бұрын

brilliant video...

@matinsakr6548 2 жыл бұрын

In your opinion, if we remove the piece that controls the voltage emitted by the generator, and adjust the rotational speed through the stove at a medium speed, neither small nor large, in your opinion, how much electricity will output, volts and amps, approximately. Thanks

@martintabuissa2122 2 жыл бұрын

good job guys keep it up

@bobbylong2202 2 жыл бұрын

🤣🤣🤣🤣😅😅 I love how you get as long with your other worker sometimes your got to tell him this is how we are going to do it lol I wish I was this smart to do what you do ..I hope to try this

@zioniolion 2 жыл бұрын

nice project guys keep up the work , who knows maybe you can make an anti gravity drive in the near future .

@skyflight1able 2 жыл бұрын

The iron rotor will be affected by the magnets and affect your bearings. I have one I purchased for wind power and it’s built that same way.

@joels7605 2 жыл бұрын

This is great work. Well done guys.

@kbte6116 Жыл бұрын

good work❤❤❤

@michelvanosch5465 2 жыл бұрын

I think the that the spacing between the stator and rotor should match. Adding more magnets or using magnets with a bigger width may cause negative results.

@brighambaker3381 2 жыл бұрын

Great video! Thank you for such a useful and well made video! There are a lot of applications for the motor in this state.

@ScienceOfProject 2 жыл бұрын

This device is very useful for generating energy Modification if best engineering 👍👍 I also work on electricity generation

@humbledb4jesus Жыл бұрын

a job very done....

@mauricio8983 2 жыл бұрын

Hi, my friend. Great educational video. I’ve got a question: where can we get the battery cells?

@randomuser_1320 2 жыл бұрын

Thread with super glue creates nice hard goodies. I would like to know your technique of winding so symmetrically. Could you make a small video on that.

@JaviersDIY 2 жыл бұрын

Very amazing

@User-fp4gn 2 жыл бұрын

great stuff

@johnM-Jr 2 жыл бұрын

So your alternator was making 12 volts are so when you turned it with drill? others are saying they can make up to 220 volts but i didnt think so. would like to see more experiments with the car alternator w neodynium magnets.

@edisondaniel5057 2 жыл бұрын

god bless you brother

@AnupKumar-cp9th 2 жыл бұрын

Good idea

@automotiveaddiction428 2 жыл бұрын

Well I got interested..cause I love car stuff so now I have to watch the videos

@davidgood5390 3 ай бұрын

Can you use superconductor magnets (now at room temperature) to remove friction on the router?

@imbw267 2 жыл бұрын

Fantastic Gonzo Engineering

@tahanlaoboy 2 жыл бұрын

Nice, thanks

@mdintesersanvi6538 2 жыл бұрын

Love from Bangladesh

@josephemerian9545 2 жыл бұрын

Very cool

@David_Palma 2 жыл бұрын

Awesome work guys, can you do a comparison between your modified rotor and the stock rotor?, working as a motor, like what's the difference on RPMs, Watts, etc. Also what is the material did you used for the rotor, steel or aluminum?

@nairityatarnekar6120 2 жыл бұрын

Hi, I have Doubt...After Conversion into BLDC motor with Permanent magnets like yours, What is minimum/maximum Voltage does it can operate. And what if supply 36/48v input from battery does it work or the winding will burn...?

@Bartetmedia 2 жыл бұрын

Attache a fan blade on the end of the alternator blowing towards the alternator to cool it down.

@The_pacesetter 6 ай бұрын

Thanks for the video. Please how can someone use a lister generator alternator to generate electricity by using a motor to drive the alternator and the output of the alternator will give load to equipments and still be able to power the driving motor back, in such a continuous way that external power will only be used to jump start it?

@panaitmarian1904 2 жыл бұрын

I have a question about what solution you use to move glue from magnets

@asollid 2 жыл бұрын

Do you have a video to show how to reduce the cogging effect?

@FAMILIAFERNANDESS 2 жыл бұрын

what is the measurement of each side x side magnets? and how many magnets does it take? Tank you 👍🏼😁

@angelit04u 2 жыл бұрын

Amazing job guys what’s the dimensions of the new rotor I’m trying to make mine and I’m following you guys steps the electric bike in here are to expensive and the top speed is 25 mph I saw you electric bike and I love it

@adamzahradnik8709 Жыл бұрын

How did you fix the drawing power?

@incodewetrust8862 2 жыл бұрын

I saw the other video where you used The same motor for the bike saying it's 10KW so you are saying if you could vet efficient wind turbine to turn the alternator at it max it would produce 10KW ?

@artkinard8678 Жыл бұрын

I would love to see if you guys can improve a standard golf cart motor

@markboweringphotography4408 2 жыл бұрын

After watching this I wonder if you could make an electric para motor for para gliding. It would be great if you could do this as a project with just hover board motors as they are more readily available.

@rocketsmall4547 2 жыл бұрын

just use a box fan

@snunley484 Жыл бұрын

Could the internal wheel, in which the new magnets are mounted, be resin printed?

@aaronsam.j7231 2 жыл бұрын

When i need a professional engineers to build stuff .my first call will be to them. All the best for your next video.but pls upload early

@farazalam7021 Жыл бұрын

Bhai AP na is ma Jo Esc contoral istaml Kiya ha vo Kitna amp ka kaha or 46 volt use Kiya ha

@davidgood5390 3 ай бұрын

Remember your PPE's (personal protective equipment) eye and ear protection when drilling

@sushillad1051 2 жыл бұрын

Awesome project, start 0 to 100% All making part in house 🏠 This motor used in electric bike , how much speed will achieve

@donniewatson9120 2 жыл бұрын

Superglue/Thread Composite; ingenious solution using available resources!

@elitehacker1416 Жыл бұрын

Except there's no such thing as a free energy generator. Ask any engineer if you dont believe me.

@donniewatson9120 Жыл бұрын

@@elitehacker1416, I'm not sure how my statement about him making a composite material using thread and superglue constitutes a free energy device. My statement had nothing to do with the project as a whole.

@m.t.6368 2 жыл бұрын

If you keep that stator, keep also the number of poles- magnets on the rotor.

@derrick32 2 жыл бұрын

can it actually be used to provide power? to house or an rv trailer?

@MrMikeyPayne 2 жыл бұрын

VERY COOL! I saw in your other video that it is 10KW. Is that continuous or peak? Thank you.

@titianonugruta9796 2 жыл бұрын

Super....

@AllenRJoseph 2 жыл бұрын

from where did you got the old hoverboard motors?

@ArshaansEdits Жыл бұрын

Nice video Bro!! is it possible for you to give the design of the 3D rotor u bilt?

@adil1087 2 жыл бұрын

using the star configuration can reduce power consumption but reduce the maximum rpm

@juand911 2 жыл бұрын

hello if you want to use it as a generator, it is more useful if you connect the coils in a star. It is as simple as desoldering the ends of the coils and connecting the ends of all the coils to a common point. So it would be 20v, or less kv if you want to use it as a motor. Good job and keep it up

@germandarkpyro4521 2 жыл бұрын

Great video is there any way you could send me the dimensions of the rotor and magnetics please I would to make one

@rosenonsikelelo2605 8 ай бұрын

Hi I’ve been watching your DIY projects and I’m loving them, I’m also doing a project with my team “ Alternator driven backup system “ but we in need of car alternator and motor. If possible can you able to sell us components or give us advice what to do

@sethturner7089 2 жыл бұрын

How can I get this exact set up

@weldonekumara1640 2 жыл бұрын

அருமை

@fernandojaroczinski4922 2 жыл бұрын

Ótimo trabalho. Ele funciona bem como um gerador? Quantos rpm pra atingir 14v e que corrente ele produz?

@jimmil2270 2 жыл бұрын

You can use Scott cast instead of glue.

@reforgedcriterion1471 2 жыл бұрын

You guys are smart! I love seeing everything you've built from scratch! My only .02 cents is that super glue degrades fast with heat. Failing temperature of superglue is less than the boiling point of water. Anyway, subscribed! I can't wait to see more projects like this!

@MrMikeyPayne 2 жыл бұрын

What glue would you recommend?

@jimmil2270 2 жыл бұрын

You can add hi power low watts dc 12v solar electric fan to power your wind turbine for more Rpm.