DL213 Xbox One Controller Joystick Replacement

Рет қаралды 28,771

DextersTechLab

3 жыл бұрын

In this quick video i replace one of the joysticks in a Microsoft Xbox One controller.

Пікірлер: 24

@Zeldorg1 Жыл бұрын

Wow that was actually much easier than i thought. I've seen a lot of youtubers basically disassemble the controller to get to the joysticks but this was so helpful. Thanks

@giovannigiorgio2262 10 ай бұрын

if the pad gone say rip to ur analog , its not ez as u think

@martinjgriffiths 3 жыл бұрын

Convinced me to fix my sons controller. Thanks for the info.

@DextersTechLab 3 жыл бұрын

No problem 👍

@longden57 3 жыл бұрын

Great video as always mate!

@johnywatkins3620 6 ай бұрын

Dude just saved my favorite controller I burned the 1st board up but the other 3 are good as new now highly recommend practicing on one of your old ones first before doing to repair on your favorite

@Todomo 4 ай бұрын

could i just heat up the solder points and use a qtip or toothpick to remove it?

@user-yd9bp3hk2n 3 ай бұрын

Hello, how many degrees soldering iron did you use?

@Ninjaclutch1130 2 жыл бұрын

What screwdriver set is that?

@cyberleone00 Ай бұрын

bought a desoldering pump because of you, hopefully i can fix it. building a customish controller for my gf :)

@chezburgergaming7515 Жыл бұрын

Would I need to calibrate the analog stick after the replacement

@Gr3yCard1nal 5 ай бұрын

I know this is an old comment but for anyone curious in case your replacement analogs don't have calibration holes in potentiometers there are special "drift fix" boards sold on aliexpress that let you do that. They are soldered on the opposite side of the circuit board and analogs.

@alexcl1741 10 ай бұрын

How do u calibrate it tho

@Red_AIert 8 ай бұрын

He skipped that part. There’s no way of knowing if he got the X Y axis centered or not. I guess that was just a fair weather friend. Lol

@wolterl9899 Жыл бұрын

If you are lucky it should be easy, if you are unlucky you keep the trigger uncalibrated because there is no way to calibrate it permanently

@Furry.D.Dragon 9 ай бұрын

That is so epic and also I have a controller that has a bad stick drift and I have the repair kit for my Xbox series s controller and I have taking apart and followed the steps and everything. And dust blow them good and it still has it badly so I need the part itself replaced so I can be able to use it again

@TheEgg185 2 жыл бұрын

This wasn't easy for ME 😠. After sucking as much solder as I could, it STILL didn't want to come apart. Are you saying the trick is to add more solder first, then suck? I used the sucking want like you showed at the end.

@bluestar99playz11 Жыл бұрын

yeah probably to melt it

@kolalbi43 9 ай бұрын

It‘s nowhere near that easy. It took me and my very skilled soldering friend like 4 hours and it was not at all easy. Would not recommend you try this unless you really know what you’re doing

@jayjayhooksch1 7 ай бұрын

I can't imagine why you would enlist a second person for this job. In any case, this is exactly the type of repair to try if you've never done this type of work before; the stakes are so low, you're only risking an already broken controller.

@samuelloader8213 7 ай бұрын

There is two motherboard types and this one in the video is the easier but the other have smaller through holes that a lot of people say are harder to get the solder out of @@jayjayhooksch1

@UpInSmoke54 7 ай бұрын

4 hours!!! Your friend is not that skilled if it took that long!

@uhhh_adam 5 ай бұрын

Sounds like a skill issue to me

@netsaeR6 4 ай бұрын

I did these when I was 12 no where near 4 hours