Man I went back and watched this one and at the end 😂 man just cracked me up "like the ford? Don't talk about it" 😂😂😂 Appreciate your content man .

best part was you smoked that prius a little lol

Another great vid I love seeing these trucks get saved and loved on and also still getting use

I have to he 6 speed in my 03. I don’t tow anywhere near the weight you pull, but it has no problem pulling 10,000 lbs down the road. It pulls a lot better then my 93 1st gen with the NV4500, but then again I’m not comparing apples to apples in the motor department. Keep up with the good work. Can’t get over how fast that little guy of yours is growing in the other videos

I'm a dodge truck guy too like the videos your doing been watching from the start keep them coming.

I remember when you first started doing KZfaq and this was the primary truck besides the 4500 you were working on. Now you've got how many trucks lol. And two challengers charger etc. Nice work man

I’m so proud of and far you have come keep up the amazing work and video’s 😊😊😊😊😊

My 06 3500 is g56. Love it. That 5 inch exhaust sounds mean Sam 👍

Don’t know why I enjoy your videos, but damned if I do. Keep up the good content. Thank you.

Aww even boon was watching you back up the trailer.

Came out nice Sam. Dually is the way to go when towing, in my opinion. I felt terrible when you reached out for those adapters and I had to tell you they were gone. Sorry...Now that we are seeing that big ball in the sky again I need to bring my truck down for you to look at...I have that unicorn you were talking about...

Hands down G56 all day everyday. Thanks for the video, I was hoping you were going to do a towing video with the new trans. I feel your frustration with the gooseneck rail system hitch. Out of my 5 trucks, one of them has the same rail gooseneck system and it sucks. It makes noise and takes up too much room in my bed but I bought it because I got a killer deal and I needed any gooseneck hitch to get me by at the time.

Cummins getting the job done period

I like the one you were driving

Thanks for the videos and the learning! We have a ‘97 dually five speed 410 gearing 4x4 which we are currently using to haul a slide in camper. Being that it is a rear drum brake it didn’t come with larger rims that are needed to fit over the rear discs. But with larger tires the gap is to close, so I would like to go with larger rims. Used rims from a newer dually would be great or maybe 19.5s which I’m not to excited about because of ride comfort, perhaps that is not an issue though with an older truck. If you have suggestions or know of any used rims or should we go with new rims, please let me know. Thank you!

Your videos are awesome. But your dog is bad ass goes with you everywhere and follows you like a puppy.

Nice job on that Sam!! The motor sounds great, and it looks like it drives great!! I've been looking around here for a dually to have a small part time biz transporting campers. 5th wheels especially, and I wouldn't do it without a dually. Hauling campers to shows, retail deliveries, customer moves and back to the factory for repairs pays pretty good here. I can get an extra $1/mile with a 2 man crew too. Anything as nice as this would be $35k+, even that old with those miles. The no-rust of course is huge too!! Nice job on that one!! --gary

Really enjoy your videos. Have you ever considered custom tunes? So much better than the box tunes.

You like the ford, don't talk about it😂😂😂 personally owned both the NV4500 and a NV5600 now. I enjoyed driving both. My 5600 is nice when I'm towing heavy with less step between gears, but on days when I run errands in it I feel like all I do is shift lol. Loved our 4500, but keeping 5th gear tight seemed to be an issue. Loved driving the 5 speed though.

That machine you were talking about that guy towing with a PJ or Big Tex was a small track digger/bucket for the power company. We use them a lot in the right of way where we can’t get trucks to the poles

Soon you'll be throwing a flatbed on it to make it your secondary main tow rig for the outfit since it's emissions exempt!

Heck yeah Sam 👍👍💪🏻💪🏻

Little upgrade made it 100 times better Need to drive it a little more

I wish I knew about filing the ridges off the splines before this. I did my nv5600 swap and a Val air dual disk and the only complaint is it’s a bitch to get it into some gears

I prefer the G 56 myself. All the good I hear about it

I have the NV4500 5 Speed Manual in a 98 single wheel and I like it,I only tow a 32-foot RV for now. Have been curious the hear what you think about the gains or losses I would experience in swapping to a G56 6-speed Manual ? thanks

Great video, I got a stock 04.5 3500 single wheel with the automatic, she will tow 10,000 lbs, but its workin, shes still got a lot more guts then a stock 96 12v. Does a tuner make that big of a difference for towing?

Sam I have a 3rd gen 3500 5,9 Cummins stock with a g56 and was wondering what I could do to get more power out of it without hurting it

Def keep an eye on your grid heater bud for your 6.7's That bolt can melt and hit your 6 cyl. Up north in canada I need it but banks has there ram air intake horn with a heater coil.

I don't like no clunkin either, damnit

Wondering what your thoughts are on the best option for me I have a p pumped cummins with an nv4500 with 3.73 gears and my trans has the 5.04:1 reverse gear wich is absolutely terrible and I want a better reverse gear which pre 97 I believe had the 5.61:1 gear can't find anywhere that says if you can physically change the gears in the trans or not or should I just try to find a nv5600 from what I can find they have the 5.61:1 reverse gear I'm only running 265/75r16s because I don't want to make my reverse gearing worse with bigger tires there are times I have had to go into low range to even get a loaded trailer to move without trashing my clutch

Any tips on tuning? Should I get a fass lift pump in my 04 5.9

I had the rail fifth wheel and it made all kind of noise even with my 16000 lb trailer. It was in an 03 ram diesel dually 4x2 the biggest pile of???? . My 1989 12 valve 4x4 wd250 pull 12000 lb trailer better than the 03 .1989 was 160 hp 400 torque. It had a getrag 5 speed with 354 gears. 03 235 460 torque with a modified 47re and 373 gears .my 2021 4x4 3500 single rear wheel pulls 20000 lb really well. It has 373 gears with 370hp and 850 torque and a68rfe and when it blows up my transmission guy will build it to be bullet proof. Denis.

I got a 2001 regular cab 4x4 dually with a NV 4500. I only pull 13-15000lb mostly. Was thinking about doing a NV5600 swap but can’t find a lot of positive things about them.

What kind of exhaust brakes do you run? I have 2005 chevy 2500hd that I cummins nv4500 swapped and I really want to add an exhaust brake to it. My brother has an 07 ram 3500hd with the 5.9l and it's got a cummins exhaust brake and I can say it's not impressive at all in my opinion.

Great video Sam always helpful. How much will you charge me to program my ECM ?

Tavit was kinda haulin a$$ today!

what turbo is in that truck and which exhaust brake? sounds great!

After the seats, and B&W, are ya gonna put your stored away load leash on the 04?!

It's funny how we can justify anything if you think hard enough 😅😅

I absolutely hate the rails! Not sure how they were ever legal either. Way to sketchy. Love me a g56.. but I don’t hate on an nv5600

What ratio rear you running? Looking at a 17 with the g56 and 3.42 rear towing 15,000 toyhauler 5 months out of the year .Wonder if that'll be a good combo or under geared

They get a lot of hate, but personally I don't think you can beat a G56. Too bad the factory had to go and derate them so much. Killed the market so they could claim no one wanted them. Pulling heavy off road on a ranch the automatic Trans get way too hot, even in 4 low. On top of that engine seems to run warm too. The G56 trucks just idle along, shift smooth, exhaust break works down to 5 mile an hour, and nothing ever gets warm.

If I have to listen to an I6 I'll take a 13l or better. Keep the revs under 1700. Pulls best from 1100-1450. 1850lbft

What year is that truck I’m trying to figure out on this 08 ram 3500 hd slt 1 ton how much weight I’ll be able to tow on a gooseneck it’s got a 6.7

I don't know my 250 2T is too fast lol

You think a Chevy 2500 would pull the smaller gooseneck trailer of yours with a 15,00 pound machine?

Nice rig. Nothing beats towing 30k with my 22 f450 though.

Juuunnnnkkkkk.. junk junk. Common rail equal🤢. Jk. Love these old Cummins and nothing can ever equal to the low end grunt of a Cummins. They become better with RPMs. Except am I the only one that hates the "crack" that the common do. Does a second gen intake really do away with that? I have a regular cab. 3500 04 and half with the 600 sticker on the black. Of course she's got some work down and a NV5600. 4.10s. she'll get you to 90 right now if you can hit the gears. Start in third skip to about 4000rpms skip 4th build the boost back in 5th but even then it wants 6th and your pinned back. It fast to 90mph then runs out of gears so. Not a race rig but would probably be faster pulling anything behind. Love that truck. Haven't dyno it unfortunately, but we're guessing 550 HP and over 1000 ft lbs torque.

I like em all but not ford haha