Don't Replace ABS Module Before Watching This | Part 2

Don't Replace ABS Module Before Watching This | Part 2 | ABS Module Components Test

Рет қаралды 60,810

Automotive Diagnosis: Cars Repair &Training Guides

Жыл бұрын

This video is the second part of ABS Module test and repair. In part 1 I explained how to test the ABS circuit, board and explained the ABS Module wiring and internal structure. I also explained how to test the ABS Module for Valve relay error fault or for ABS Motor Electrical fault.
But in this video I will go further to explain how to test the MOSFETs and Solenoid valves inside the ABS Module. I also explain the difference between ABS and ESP/TCS in terms of internal structure and how to know the normal value for the components during the test.
Part 1 of this video can be found in my channel or using the link below:
• Don't Replace ABS Modu...
Join the channel for more videos and more support:
www.youtube.com/@AutomotiveDi...
You can also find the ABS internal diagram that I presented in the video in the following link:
drive.google.com/file/d/1Pzz8...
And for downloading the ABS internal components diagram use the link below:
drive.google.com/file/d/1jbpZ...
Finally a Perfect Budget Friendly Scanner for DIY & Pro Mechanics That Can Do Everything !!!
• OTOFIX Lite Review | A...
#ABSmodule
#how to repair ABS Module
#RepairABS
#tcs
#esp
Disclaimer:
Any information contained in this video is just the understanding of “Automotive Diagnosis: Cars Repair & Training Guides” and it is not an official guide or reference, so everything provided in this video is just a share of our experience and understanding and they are provided as a courtesy for your reference only. So, if you are using any part of this video, use the information at your own risk. We highly advise you to check the manufacturer owner’s manual before performing any act of removal, diagnosis, inspection, or repair on your car to know about what you are authorized to do on your car, what the correct and legal procedure is and what risks might be involved, also viewers are strongly advised to consult a licensed person before any sort of inspection or repair. Due to the factors beyond the control of “Automotive Diagnosis: Cars Repair & Training Guides”, we cannot guarantee against improper use of information or tools or systems, or the procedure provided. “Automotive Diagnosis: Cars Repair & Training Guides” disclaims any damage, injury or loss caused by your decision to follow the steps provided in this video.

Пікірлер: 219

@AutomotiveDiagnosis Жыл бұрын

Please watch the Part 1 of ABS Module Test & Repair in the following link: Don't Replace ABS Module Before Watching This | Repair ABS Module for Motor & Valve Relay Error kzfaq.info/get/bejne/obt3f5hk0LS8g3k.html

@Ed-ty1kr 18 күн бұрын

Thorough explanation of how the part functions and how to check common issues. Outstanding information.

@AutomotiveDiagnosis 18 күн бұрын

Thanks for watching. I’m glad you liked it.

@stephendennis7871 Жыл бұрын

Another excellent follow on video to the first one, very informative with clear video pictures to go with the explanation

@AutomotiveDiagnosis Жыл бұрын

Thanks a lot for your comment.

@josephmcmonagle5901 2 ай бұрын

That was totally amazing. Thank you so much for taking the time to make these videos.

@AutomotiveDiagnosis 2 ай бұрын

Glad you like them!

@cliveradvan3414 5 ай бұрын

Fascinating insight! Thank you so much for your great presentation.

@AutomotiveDiagnosis 5 ай бұрын

Glad you enjoyed it!

@giterdunpete Жыл бұрын

I think these 2 videos go a long way to explaining the error codes in BMWs which a mechanic is never going to string together with an electronic fault. And just removing and replacing the large connector is a WORK AROUND which if it works is destined to fail again. So well done .

@AutomotiveDiagnosis Жыл бұрын

Thanks a lot, I'm glad you liked the video.

@arazaliguliyev Жыл бұрын

i was looking for such an educational chanel like this👍

@AutomotiveDiagnosis Жыл бұрын

Hi my friend and thanks for your comment. Welcome to this channel, I'm glad you found it helpful. ❤️

@ScientistPrepper 9 ай бұрын

Great video. I learned a lot. I'd like to see another video in the abs module series.

@AutomotiveDiagnosis 9 ай бұрын

Thanks 🙏, more videos are coming about ABS module

@drissjakane2683 8 ай бұрын

Thank you so much for this practical video this all waht we need to learne how to controle moduls👍

@AutomotiveDiagnosis 8 ай бұрын

Hi my friend. I’m glad you liked it.

@mohammadal-gebaly3046 Ай бұрын

Thank you very much , professional job , I enjoyed it , watching you from Egypt , appreciated

@AutomotiveDiagnosis Ай бұрын

Hi my friend, thanks for watching

@GarethDavies-hk9cg 3 ай бұрын

Thank you for two very interesting videos.

@AutomotiveDiagnosis 3 ай бұрын

Glad you like them!

@agdoservice 10 ай бұрын

Excelente vídeo ! Parabéns ! Sua disposição para ensinar e algo divino ! Feliz por sua disposição,Obrigado.

@AutomotiveDiagnosis 10 ай бұрын

Thanks for your kind words. I’m glad you found the video useful.

@cartech5015 Жыл бұрын

Perfect explanations.

@AutomotiveDiagnosis Жыл бұрын

Thanks

@NishanthaMillagala 11 ай бұрын

Dear sir Its very nice explain. Thanks so much .

@AutomotiveDiagnosis 11 ай бұрын

I’m glad you enjoyed it 🙏🙏❤️

@amarabdelli487 Жыл бұрын

Thanks for sharing, perfect explanation

@AutomotiveDiagnosis Жыл бұрын

Thanks for your comment.

@esmfamil3929 Ай бұрын

A nice and helpful explanation , thanks a lot .

@AutomotiveDiagnosis Ай бұрын

Glad you liked it

@antonispk6760 16 күн бұрын

Very helpfull video !!

@AutomotiveDiagnosis 16 күн бұрын

Glad it was helpful!

@maar5725 Жыл бұрын

بعد شُكر الله ؛ شُكراً لــككك ؛ Thank you very much Good steps

@AutomotiveDiagnosis Жыл бұрын

Thank you very much for your comment.

@luisramos3427 5 ай бұрын

Super helpful!👍👍👍👍👍

@AutomotiveDiagnosis 5 ай бұрын

Glad you think so!

@mariocarmecanicaautomotiva8602 3 ай бұрын

Estes dois vídeos me ajudaram muito aqui no Brasil, total gratidão por compartilhar seus conhecimentos, peço que Deus te abençoe grandemente

@AutomotiveDiagnosis 3 ай бұрын

Hi my friend. Thanks for your comment. I’m glad videos were helpful.

@dipakmanu1842 Жыл бұрын

Thanks a lot, I have watched the first one more than 5 times I think 😊 this one is great too ❤

@AutomotiveDiagnosis Жыл бұрын

👍👍❤️❤️

@shaunchetty4223 20 күн бұрын

Awesome

@TripleBRanch 2 ай бұрын

@AutomotiveDiagnosis thank you for the video. I checked everything you checked and all tests were good. The original fault code was “C2200 Antilock Brake Module Internal”. I would guess the trouble will still be there if I just reassemble… my car is a 2015 Jeep Wrangler JK. Any advice will be greatly appreciated.

@gcauto6946 Жыл бұрын

Thanks for the great job! See if you can make a following video, to explain the operation of the MCU and the controller, Thank you!

@AutomotiveDiagnosis Жыл бұрын

Thanks for your comment. Sure thing, I will try to do my best 👍

@bwagizoselemani8434 Жыл бұрын

Thenk you sir for a good lesson

@AutomotiveDiagnosis Жыл бұрын

I'm glad you liked it.

@user-tt4xy9rd4s 10 ай бұрын

thanks, useful information

@AutomotiveDiagnosis 10 ай бұрын

So nice of you

@suatkaleli5075 29 күн бұрын

better than others thanks

@AutomotiveDiagnosis 29 күн бұрын

Thanks for watching

@bluedeckelectronics 11 ай бұрын

Good video !

@AutomotiveDiagnosis 11 ай бұрын

Glad you enjoyed it

@LooneyRanger Жыл бұрын

Perfect. Tq u so much

@AutomotiveDiagnosis Жыл бұрын

❤️❤️

@johnreyzabala3163 9 ай бұрын

wow great nice video

@AutomotiveDiagnosis 9 ай бұрын

Thanks, I’m glad you liked it

@sandyshrimp8463 Ай бұрын

This was a great video. I checked the motor mosfet (mine is a PN0404 for a jeep) and have an OL reading between the gate and the drain. Should I assume the mosfet is bad? thanks again for the video and for any help you can provide.

@ravigarage8745 Жыл бұрын

Excellent

@AutomotiveDiagnosis Жыл бұрын

👍👍👍

@juvehe Жыл бұрын

This is very cool! Thanks for sharing your knowledge.

@AutomotiveDiagnosis Жыл бұрын

Glad you liked it and thanks a lot for your comment.

@juvehe Жыл бұрын

@Automotive Diagnosis: Cars Repair &Training Guides if I can suggest one thing to make your awesome video more awesome: show how to check integrated circuits. I have an MK60 module off of a 2002 BMW 325i, got the trifecta lights on my dashboard. Turns out I have a bad IC (9369.1D).

@juvehe Жыл бұрын

@Automotive Diagnosis: Cars Repair &Training Guides in case anyone is curious, the error code I get is 5DF5: ABS-DSC internal fault, control unit.

@AutomotiveDiagnosis Жыл бұрын

@@juvehe Hi there, Thanks a lot for your comment and sharing your experience. I explained more on the first part of this video but as you said there is more way to go and hopefully I can make another video too.

@AutomotiveDiagnosis Жыл бұрын

@@juvehe Thanks a lot for sharing your experience.

@somarpr 4 ай бұрын

Excellent video, great explanation in this excellent course on how does a ABS module works and I can relate it to how intermittent ABS should be worked and diagnosed. Thank you. What did you use to close it back and water proof it.

@AutomotiveDiagnosis 4 ай бұрын

Glad you enjoyed it! I usually clean up the old seal and apply new black silicone.

@maar5725 Жыл бұрын

بعد شُر الله ؛ شششكراً لّككك ،،، Thank a lot ,,, You did great job in very excellent demonstration I ever seen .

@AutomotiveDiagnosis Жыл бұрын

Thanks a lot. I'm glad you liked it.

@gabrielgv252 6 ай бұрын

Excelent video

@AutomotiveDiagnosis 6 ай бұрын

Thanks

@longhuynh5249 11 ай бұрын

Brilliant indtructions

@AutomotiveDiagnosis 11 ай бұрын

🙏🙏

@i.fix_iran6097 7 ай бұрын

good job👍

@AutomotiveDiagnosis 7 ай бұрын

Thanks for the visit

@sahsaker 10 ай бұрын

1st thank you very much if this great vedio I meet 2 times problems with my car 1 st one the module stoped because the vacuum pump not working but motor working properly I changed already abs unit 2nd one after time too have a problem get the oil from pump to module Now I want to repair the old pump but the pins on not released this pins on motor head inside the pump

@AutomotiveDiagnosis 10 ай бұрын

Hi there, I didn’t quite get the question, is there any fault code right now? If brake fluid is not coming into ABS module, this is not the ABS motor fault, you must check the master cylinder.

@watkinsrcful 9 күн бұрын

Thank you

@AutomotiveDiagnosis 9 күн бұрын

Thanks for watching

@user-ii1un6fq3h 9 ай бұрын

Best ever

@AutomotiveDiagnosis 9 ай бұрын

Thanks

@Walopa_uie 3 ай бұрын

sir i check all mosfet is good .. the error code is u3000 hope you notice this one sir thank you for sharing👍👍👍

@leethomas9198 8 ай бұрын

Thank you for identifying the electrical components. Where is a good source for these components and tech sheets besides Google?

@AutomotiveDiagnosis 8 ай бұрын

Wiring diagram is better than any other source.

@dapurperadaban7710 10 ай бұрын

Thank you very much, this is great explanation, do you have any video for how to check the IC5895-5220C if there's IC fault, how to check it? and how to scan it directly the ABS module in bench (pinout connection to OBD scantool). can you share the diagram for Ford Fiesta 2011-2014. again, thank you very much!

@AutomotiveDiagnosis 10 ай бұрын

Hi there, we don’t have any videos for inspecting that IC, but I will try to get one.

@176robles 8 ай бұрын

MY Grand Vitara 2011 ABS is near desame, where can a get wiring diagram like this one you have?

@mazdaservice6533 Жыл бұрын

Thanks bro

@AutomotiveDiagnosis Жыл бұрын

👍👍

@greggutierrez7760 3 ай бұрын

Great instructional videos on ABS module operation and diagnosis. My question is, if you cut the plastic cover off then how do you ever re-use the module if it tests good? Seems like this is destructive testing? Good to know if you're just interested to see where your old module failed but not useful for actual repair correct?

@AutomotiveDiagnosis 2 ай бұрын

Hi there, of course we seal the cover back on, unless what’s the whole point of testing the unit? So, we must be very precise when removing the cover, then we seal it back on.

@OnYok1974kuwait 3 ай бұрын

👍👍👍

@AutomotiveDiagnosis 3 ай бұрын

👍👍

@matmechanic5909 Жыл бұрын

Thanks

@AutomotiveDiagnosis Жыл бұрын

👍👍

@newyorkerturbo 7 ай бұрын

hello what an explanatory video are you giving me the courage to do it too, I tell you that I have a 2008 jeep grand cherokee with a similar module I have the DTC C2200 the only thing I have seen with the scanner is that the valve feed oscillates between 5 and 10 volts before the DTC appears when starting the vehicle and exceeding it of 15 miles the lights come on and in the scanner the valve feed is It's still at 5 volts, do you think I could fix it if I open it? 🤔

@AutomotiveDiagnosis 7 ай бұрын

Hi there, thanks for your comment. This code is due to an internal failure on ABS Module, Sometimes it could be something we can find by checking all connections in the ABS module, but sometimes is coming from the main microprocessor which is hard to repair. So basically there could be different possible causes for each different case, and we can only be sure after inspecting the module carefully and thoroughly.

@supercomputerbug 11 ай бұрын

please show how to verify opening function of mosfet. if i am right, by charging the gate by touching with + of multimeter, the mosfet opens.

@IdaIda-vx8hp 2 ай бұрын

Thank your explanation, I got the problem the resistance are different 2 ohms between blue, 9 ohm and 8.8ohm this acceptable? , my car problem abs right rear cannot detect.

@AutomotiveDiagnosis 2 ай бұрын

HI there, that much difference is not a big deal. May I ask the fault code too?

@drv8086 7 ай бұрын

Okay dude, you gotta tell me, where did you find these diagrams. It’s exactly what I was looking for! Edit: thank you for this wonderful video btw

@AutomotiveDiagnosis 7 ай бұрын

Hi there, thanks for watching the video, there are different ways we can find the wiring diagrams, Some manufacturers have designed the OEM scan tool with wiring diagrams (KIA, Hyundai, SsangYong etc.) so if you have those scan tools, you have the diagrams too. Also, in addition to the manufacturers technical websites, some other private companies offer the wiring diagrams and workshop manuals too.

@drv8086 7 ай бұрын

@@AutomotiveDiagnosis that’s fantastic, I’ve been really struggling to find the wiring diagram of my 04 Kodiak Topkick. I may have to look into some of those private companies or scan tools you mentioned. I saved the ones from your description and I can’t tell you how much it helped. Thanks again!

@AutomotiveDiagnosis 7 ай бұрын

@@drv8086 I'm glad it was helpful. I will check for that wiring diagram as well and will keep you posted here if I find any.

@drv8086 6 ай бұрын

⁠@@AutomotiveDiagnosisThank you so much, if you do happen to find anything it would be very much appreciated. I’m still having trouble diagnosing exactly what’s gone wrong. A diagram such as what you have outlining the pin out would be wonderful!

@ronlisto4790 11 ай бұрын

Great video. Question: 2009 Ford Escape with very low brake pedal. No codes or lights. Replaced master cylinder, all shoes & pads good. Had shop bleed ABS module with scanner. No change, still very low pedal. Is ABS module causing this? Thx

@AutomotiveDiagnosis 11 ай бұрын

I don't think that's ABS fault, if it is, it shows itself when you do the bleeding. Pedal is low, but how you feel the pedal?

@leethomas9198 8 ай бұрын

The low pedal position could be the end of the rod connected to brake pedal. Most Fords have an adjustable screw on end. I think it is a 7mm and you can lengthen it to cause pedal to react quicker.

@unclefranko2452 11 ай бұрын

Hi mate ,good video, how do you manage to get the cover off ???? Please regards Frank

@AutomotiveDiagnosis 11 ай бұрын

Thanks for your comment. I simply use a small cutter to do it carefully.

@humbertholzmann674 2 ай бұрын

nice video but at the end can it be repaired fixing soldering?

@AutomotiveDiagnosis 2 ай бұрын

Of course it can, if there is any broken solder, it could be the source of the problem. But as I said, that’s not the only possible cause, there are many other causes that are explained in the video.

@sangeethkumar6727 21 күн бұрын

Where can we get the schematic diagrams of the electronic components of the ABS ECU and the hydraulic schematic of the ABS valve body for other cars

@user-wd8kv9yf4c 7 ай бұрын

Excellent video. What about when a component is faulty. I have an abs error code indicating a wheel speed sensor problem but everything is fine. The problem is probably within the abs module. The question is which faulty component of the module will keep the brakes locked on one side only when the abs light is lit and the brake pedal not depressed?

@AutomotiveDiagnosis 7 ай бұрын

Hi there, that problem could be coming from the ABS valves, but you need to check the brake caliper as well, sometimes brake piston or sliding pin is sticky.

@user-wd8kv9yf4c 7 ай бұрын

Can the ABS module can be damaged if the wire harness cause a short because of a shafted wire connecting to the ground? Or the module is protected somehow in these situations.

@mofeedfouad7391 11 ай бұрын

First of all thank you for your efforts I have jeep grand cherokee 2011 my front wheel lock properly but my rear wheel not lock the wheel enough, I have changed everything but not the abs because there's no abs or any light in shown im my dashboard, And when I try to bleed the rear ones the brake oil the pressure of it approx. Nothing compared to front ones Do you have any advice?

@AutomotiveDiagnosis 11 ай бұрын

Hi there, Have you checked the master cylinder?

@mofeedfouad7391 10 ай бұрын

@@AutomotiveDiagnosis Yes already replace it with new mopar

@KPoth-hj3mh 4 ай бұрын

thank you for sharing. where we can find the wiring for an ABS unit? I have a ATE controler 28.5162-2917.3

@AutomotiveDiagnosis 4 ай бұрын

Thanks for watching. I normally get the diagrams from the dealers technical website or those online websites offering the diagrams for a fee. But not all of those diagrams provide enough details. May I ask what model your car is?

@athulprakash77 9 ай бұрын

I bike lever is harder when applied front abs brake what cause the problem i get the braking but its little tight

@lsp5745 4 ай бұрын

Hi, I'm getting this code. Everything I checked with your vids is OK. mosfet Ok. C1043: Master cylinder cut solenoid valve circuit No.1 failure

@AutomotiveDiagnosis 4 ай бұрын

May I ask your can make and model?

@lsp5745 4 ай бұрын

@@AutomotiveDiagnosis Yes! Suzuki Grand Vitara Year 2012. Where are the transistors for the solenoids? The two mosfets seem to be Ok, following your indications. Also I tried to look for the pinout of two big chips on the card, but can't find the datasheet.. I've got some electronics experience so I'm trying to solve it myself...Thanks!

@RianKurnia 10 ай бұрын

Penjelasan yang mudah dipahami. Saya ingin bertanya pada anda, bagaimana cara memeriksa kode kesalahan u3000 pada modul abs ford fiesta? Mohon dijawab, terima kasih.

@AutomotiveDiagnosis 10 ай бұрын

Hi, for this code you need to check the power and ground on ABS Module and also CAN-BUS terminals.

@JEscGod 4 ай бұрын

Hi, i have a 2012 chevy equinox with ABS, brake and stability track lights on at same time, do you think the ABS module can be repaired?

@AutomotiveDiagnosis 4 ай бұрын

You must check the fault codes first, sometimes it’s not a very serious issue

@eluno72 3 ай бұрын

Hello ! I have a problem with a 2013 terrain ABS module, the code is U0073 00! I try to buy a new module and program it but it is impossible to get it. Could you guide me if it can be repaired or tell me what I should check? Thank you

@IgorReviews 6 ай бұрын

Хорошо, что английский я знаю)

@AutomotiveDiagnosis 6 ай бұрын

😊👍

@user-rc2yw1bc9f 9 ай бұрын

Make a video on Hyundai ABS please

@AutomotiveDiagnosis 9 ай бұрын

Sure thing

@juanjoalbarello442 3 ай бұрын

is this ABS Module from a Ford Focus SE? because is very very similar...

@AutomotiveDiagnosis 3 ай бұрын

No my friend, but very similar

@carsmobileservice1846 Жыл бұрын

Do you guys have any video about electric parking brake too?

@AutomotiveDiagnosis Жыл бұрын

Yes, we do a couple of videos for EPB on different cars (more vides are coming though), I will send the link here.

@AutomotiveDiagnosis Жыл бұрын

How To Release Electronic Parking Brake on Mercedes CLA 45 Before Replacing the Rear Brake Pads kzfaq.info/get/bejne/qJ2hkrqW3dqmp4U.html

@AutomotiveDiagnosis Жыл бұрын

How to Fix C10E254 Fault Code on VW Golf Electronic Parking Brake (EPB) Just in 2 Minutes kzfaq.info/get/bejne/sLiUZ5ty1Letg3k.html

@Walopa_uie 4 ай бұрын

sir i check all mosfet and all coil is good.. my final is cpu or ic ?? do you think im right, if change ic , need to program sir or no need..thanks for helping sir,gdbless

@AutomotiveDiagnosis 4 ай бұрын

Hi my friend. May I ask what is your fault code exactly?

@Walopa_uie 4 ай бұрын

@@AutomotiveDiagnosis u3000 49-68 control module, panel lights on abs, traction and steering angle sir..

@Walopa_uie 4 ай бұрын

@@AutomotiveDiagnosis not steering angle sir the other one light is uphill..

@ratheeshkrishnan1623 10 ай бұрын

Can you do the video of Bosch abs 5.3 module

@AutomotiveDiagnosis 10 ай бұрын

Hi there, I will, as soon as I have that module.

@geodirecoes2778 9 ай бұрын

Eu sou do Brasil, muito sua boa explicação!! Estou com problemas em um abs do ford FUSION!! Vc poderia me ajudar?

@AutomotiveDiagnosis 9 ай бұрын

Hi my friend, I try to do my best, what is the problem with your ABS?

@geodirecoes2778 9 ай бұрын

@@AutomotiveDiagnosis ele não comunica com scanner

@geodirecoes2778 9 ай бұрын

Quero um treinamento guiado com você !

@AutomotiveDiagnosis 9 ай бұрын

@@geodirecoes2778 When there is no communication, it could be power supply, ground or CAN-Bus problem. It's better to start from Power supply on ABS module, normally there are 2~3 power supply, one is for ABS motor, one is for ABS valves and the last one is for ABS control module, the last one is very important for the communication. If power is okay, find the pins for ground and inspect them. ABS connector also must be carefully checked for any dirt, moisture or looseness.

@geodirecoes2778 9 ай бұрын

@@AutomotiveDiagnosis muito obrigado pela atenção, vou verificar

@user-tl3gp8re3r 4 ай бұрын

Ola,queria saber teste para código U3000 Ford New fiesta ,falha eletrônica interna

@rhinoleveling 11 ай бұрын

I have a unit like this one. ATE MK60E it keeps throwing C2200-49 internal module failure. I have already verified that motor & valve circuits are good. I'm scratching my head on this one. Any insight would be greatly appreciated.

@AutomotiveDiagnosis 11 ай бұрын

Thanks for sharing your experience. If you have checked the components as described in this video and part 1 (link in description), it could be the control unit failure which does not switch the actuators on.

@rhinoleveling 11 ай бұрын

@AutomotiveDiagnosis sounds correct when I clear the code it's fine, has bidirectional comm. Until wheels start rolling as soon as I hit 2 mph, it comes back

@braddunn5983 9 ай бұрын

@AutomotiveDiagnosis what do you check or replace for this situation, where the control unit doesn't turn it on?

@alimuddin3018 5 ай бұрын

@@rhinoleveling I have same problem too.dont now what to do

@stevowhit3121 5 күн бұрын

Great info. I have a 2013 Ducati Multistrada with bosch abs. I get a random """abs pressure sensor fault.: C1006, C1007""". Totally random sometimes not for hundreds of miles other times every 25? The fault resets when ignition is off / on. I have bled and flushed both front and rear many times with quality brake fluid. Abs operates when not faulted. When faulted the brakes are fine except no abs function. Ideas please. Thinking of pulling the module and checking solder joints. It seems like a bad connection due to the intermittent occurrence of the fault. Anyone having pressure errors faults ? All info I get is to replace module. Thanks in Advance. Cheers

@zackkennedy9266 9 ай бұрын

Hey if a mosfet is bad can it throw off the modfest next to it when doing the diode funtction test

@rogerbsp1 5 ай бұрын

Hi there, it's possible communicate abs module with scanner without the others modules? I'm trying but the communication don't starts.

@AutomotiveDiagnosis 5 ай бұрын

Hi there, I didn’t quite get it. You mean ABS doesn’t communicate with scan tool or it doesn’t work with other control units?

@rogerbsp1 5 ай бұрын

@@AutomotiveDiagnosis I was trying to connect the scanner directly to the abs module, but the communication was not working. I even tried with a 120 ohm resistor between the CAN H and CAN L lines, but it still didn't work. So I connected the injection module to the CAN H and CAN L line and this time I managed to communicate with the scanner.

@Sunny-uk5fn 7 ай бұрын

Would be interesting if this solves the error code C1288, error at ABS pressure sensor

@AutomotiveDiagnosis 7 ай бұрын

It’s a bit complicated for the pressure sensor as it’s controlled completely by the control unit, but it is absolutely possible.

@japzonerazan744 6 ай бұрын

You can fix the code c1288 by changing the brake cylinder may be its defective, or the fluid is contaminated , this 2 are the reason why creating of pressure to the brake system,

@giulianofabbrinioficial Жыл бұрын

how can i fix, test or replace the pressure sensor? tks

@AutomotiveDiagnosis Жыл бұрын

Hi there, Pressure sensor is the hardest one as it senses the pressure and gives it directly to ABS module, so the only section to check is the contact between the pressure sensor and ABS module. In most cases we have to replace the ABS module is case of having a faulty pressure sensor.

@pedroqueiroz8097 16 сағат бұрын

Ola .tem curso reparo ecu abs?

@AutomotiveDiagnosis 16 сағат бұрын

Hi my friend. We are working on some courses including the ABS, will let everyone know as soon as they are ready.

@revbikerbigd8664 2 ай бұрын

2014 f150 has a code C1440 can i repair my module??

@AutomotiveDiagnosis 2 ай бұрын

This is a tricky one, most of the times the entire ABS module must be replaced.

@germany4650 Ай бұрын

здраствуйте, я все видео до конца посмотрел но так и не понял именно в чем было проблем? потому что у меня не удаляется это ошибка c2112

@AutomotiveDiagnosis Ай бұрын

Watch this video for C2112: kzfaq.info/get/bejne/fJiCnKqc1LGdj5s.htmlsi=xFe4fstEajurNX_x

@raulfloresreyes2112 10 ай бұрын

tengo dudas cuando el modulo de abs marca el codigo de falla ABS ACTIVADO cual seria la solucion en este caso?

@AutomotiveDiagnosis 10 ай бұрын

Please send the entire fault code here

@zola1981 8 ай бұрын

My ABS module was failing. The motor remain ON even if I close the car. I soupose the transitor it's remain blocked ON or the microcontroller gives power to the transistor...

@AutomotiveDiagnosis 8 ай бұрын

Hi there, yeah, it could be a short to power or ABS unit malfunction. Most likely there is a fault code as well.

@ponchoaag 7 ай бұрын

do you have a diagram specific for a MB c 280 2009 2009 MERCEDES-BENZ C 280 (204.054) WDDGF54X69F166637. Im really trying to verified and repair the module , because no body could do it , so want to try.

@AutomotiveDiagnosis 7 ай бұрын

I will check and send the diagram here if I have any.

@Gerber_Gaitan 9 ай бұрын

For Mazda 3 2010 mechanical ?

@AutomotiveDiagnosis 9 ай бұрын

And what is the problem exactly?

@carlosg802 10 ай бұрын

abs engine will have oil leak inside just like it happens with master cylinder please answer me appreciate

@AutomotiveDiagnosis 10 ай бұрын

Hi there, I didn’t quite get the question, you mean break fluid leak inside the ABS module?

@carlosg802 10 ай бұрын

im sorry my friend i was trying to said is the abs motor if is leaking interior like happing with master cylinder brake

@carlosg802 10 ай бұрын

abs motor not module

@AutomotiveDiagnosis 10 ай бұрын

@@carlosg802 I haven't seen any internal leak on ABS motor, but internal leak on valves is possible.

@timrogers4124 10 ай бұрын

where do you get your drawings?

@AutomotiveDiagnosis 10 ай бұрын

In some cases, I get them from the companies technical websites, some companies like Kia and Hyundai provide the wiring diagrams on their scan tools too.

@ratheeshkrishnan1623 10 ай бұрын

If remove electronic control module and can drive the car

@chaunguyen5102 4 ай бұрын

this bmw abs series ?

@AutomotiveDiagnosis 3 ай бұрын

This was not for BMW but they are very similar

@justme8956 9 ай бұрын

Wer was the problem, most o them ,just bad contacts, main processor or conscription plug

@AutomotiveDiagnosis 9 ай бұрын

Yeah, absolutely, most of the times it’s poor connection.

@mohanraj2398 6 ай бұрын

i20 ABS 3 wheels bleeding. But one wheel not bleed.. what's problem????

@AutomotiveDiagnosis 6 ай бұрын

You mean it keeps giving air bubbles from that wheel?

@mohanraj2398 6 ай бұрын

@@AutomotiveDiagnosis 0% oil flow in 1 wheel

@netoferreira8708 Ай бұрын

I have error code b1342 on my Ford Fusion 11. Have you ever caught anyone with this error?

@AutomotiveDiagnosis Ай бұрын

Hi there, this code has many different possible causes, have you checked other systems as well for any fault code?

@LooneyRanger Ай бұрын

I have code eror c0082 and u0415, what i am chek

@LooneyRanger Ай бұрын

Mazda biante skyactive

@AutomotiveDiagnosis Ай бұрын

@@LooneyRanger I would check the ABS module connector first, then check the ABS fuse inside the engine fuse box.

@netoferreira8708 Ай бұрын

@@AutomotiveDiagnosiswithout other errors. I have already checked the wheel sensors and the ABS works and does not lock the wheels. I will send it for repair. grateful.

@abdulhamza920 10 ай бұрын

iam working on peugeot 301 abs i daignose it i find front right sensor and front left sensor not working and i opent it i fund some line on the board and i repair it and fix it back he didni worh so i need some help thank

@AutomotiveDiagnosis 10 ай бұрын

Have you checked the wiring between ABS module and sensors?

@northernpatriot9078 Жыл бұрын

What if its on yhe car with wires

@AutomotiveDiagnosis Жыл бұрын

There are some other videos on the channel explained those how to check the ABS module on the car too, I will send the links here.

@AutomotiveDiagnosis Жыл бұрын

How to Test & Fix the C2112 ABS Valve Relay Error | ABS & ESP Fault Code kzfaq.info/get/bejne/fJiCnKqc1LGdj5s.html

@AutomotiveDiagnosis Жыл бұрын

How to Test & Fix C1266 ABS or ESP Valve Power Circuit Failure on Ford | ABS & ESP Fault Codes kzfaq.info/get/bejne/hLpzeKlpq7nVhIE.html

@mrklobouk 4 ай бұрын

This is from bmw?

@AutomotiveDiagnosis 4 ай бұрын

No, it’s a Chevy,but they are mostly the same .

@jancloddlafront9185 3 ай бұрын

oh great... class but you are not actualy trying to fix this module and neither are you offering a solution to fix the problem, Right? that some info I didn't understand anywhere on the 2 videos... great stuf any way. But have you even found a problem on an Abs module this way?

@AutomotiveDiagnosis 3 ай бұрын

These two video are not only for one single fault code, there could be multiple faults on ABS module, that’s why I explained how to check the internal components one by one. I think the solution are very clear, you see how to check any of those components, so if there is anything wrong in your inspection, you have to proceed to repair. For example, any fault on ABS motor or valve relay circuit can be checked step by step by following the videos.