Thanks for the info I just picked up a 461. I'll dial in those settings
@patthesoundguy2 жыл бұрын
Can't buy that kind of experience and wisdom, you can only earn it by doing the job. Great stuff! Thanks for sharing the love
@200cdl4 ай бұрын
Very helpful. Thanks
@nateolmsted8992 жыл бұрын
Thank you for all the great information Donnie love the channel
@jensenwilliam54342 жыл бұрын
Hello Donny!!! AND THANK YOU!!!!
@timothyfolk47692 жыл бұрын
Thank You Donny. Just pulled my carb off my 461. And was hoping for some instructions So happy for your intell. Explained perfectly.
@justinweaver87872 жыл бұрын
Awesome tips buddy thank u!!
@230e42 жыл бұрын
Thanks for doing this video. My 461 has been spot on with the carb settings you put it at. I richened it up slightly when it gets really cold here. It can be confusing setting the high jet with a tachometer and the limited coil unless you know the ideal RPM in the cut and being mindful of the needle position in relation to the recommended stock setting while you are adjusting. One cannot stress enough that you have a sharp chain and make sure your air filter is really actually clean before adjusting the carb. Shine a light into the filter and make sure you can see light through it on the HD-2 filter. Clogged pores on these filters really hurts the power of the saw. Checking your spark plug after adjusting and running for awhile is a good idea as well.
@donnywalker46912 жыл бұрын
Your on the money good job
@thebradleysoncatbirdhill68492 жыл бұрын
I will be looking forward to the 7310 demo, as I have one and really have fallen in love with it. I think it's an exceptional value. 💪👍
@alexpearson61972 жыл бұрын
Good to know thanks 👍
@aristeogonzalez6315 Жыл бұрын
Great video thank you
@jimssawsnstuff89032 жыл бұрын
Great tips. On the new 461I got in last week, I popped off the little metal cover that goes around those caps, then pulled them both out to tune it. Great point about cutting air! Saw only cuts wood when the chain is touching it 😎👍
@donnywalker46912 жыл бұрын
You got it Jim how ya doing 🪵👍
@jimssawsnstuff89032 жыл бұрын
@@donnywalker4691 pretty good Donny, it warmed up again, was pretty cold earlier this week.
@angargoy71812 ай бұрын
*Gracias por esta informacion no sabia como retirar los seguros.*
@horseshoeshandgrenades53849 ай бұрын
Thank you. Looking at getting a 461
@dpete8995 Жыл бұрын
Good info!… thanks Donny!
@codybrown39462 жыл бұрын
Good to see ya buddy ✌️
@DirtRoadLanding2 жыл бұрын
Great Tutorial!!!!
@VT587411 ай бұрын
Can I keep the adjustment limiter out after removing? A friend said they need to go back in, but wouldn’t shaving the small tab off be the same as not having them at all? Thank for the help
@yasurebud2 жыл бұрын
Hi Donny! Just clarifying, you're removing the limiter caps just to double check the carb is at stock setting? I'm assuming you can set the high and low to those stock settings with the limiter caps still on? Thanks
@robertboten49442 жыл бұрын
Where can I buy a sweatshirt like your wearing.
@bobhaddock957 Жыл бұрын
have MS 460. carb # HD 16 443. # on the carb itself. same settings on the MS 460 ?
@maximopawilenbumatnongjr.9032 Жыл бұрын
Good day sir. How to tune up the MS 070 STIHL sir? Thank you sir.
@mbm23552 жыл бұрын
Hey, Thanks Donny! Glad I subbed to your channel after stumbling across your videos over at Buckin Billy Ray's. I never felt my 461 needed any adjustment after installing the Bark Box from West Coast Saws. They actually recommended grinding off the tabs and retuning after installation but I held off. I figured I'd get the hang of running the saw without modification, then grind if needed; but aside from some minor adjustments for cold and different performance gasolines, it never needed a boost. Pulls just fine with a 36" bar through everything except the largest Live Oak around here. In hard, wavy oak I just let the saw pull itself, no encouragement from me. Only bogs a bit if I start really leaning on it. Again, that would be running a 36" bar with a full house chain, square filed. I have a hunch though, that's because I need practice on my square filing. I'm terrible at it, but opportunity for practice is knocking.. With a 24 inch bar on it, the saw couldnt care less what I'm cutting.
@donnywalker46912 жыл бұрын
Cool bud the new hexa chain and file will be out soon it looks good chisel filing in to the tooth is a art you need patients and understand it
@pm2701002 жыл бұрын
good info there don but i have an old 046 mag
@donnywalker46912 жыл бұрын
Good saw adjust rpm at 13500 to 14000 and like I say good fuel mix sharp chain rock on
@pm2701002 жыл бұрын
@@donnywalker4691 thanks don
@jimmyhuffman68022 жыл бұрын
Oh no !
@jrhensels7112 жыл бұрын
would you mind sharing some info on the 7910's your building ive got 5 of them lol not much information or content on them out there
@donnywalker46912 жыл бұрын
You mean 7310
@donnywalker46912 жыл бұрын
Oh Dolmar you mean I think there a great saw I have done a couple they ripp
@hjvilhelmsen8848 Жыл бұрын
Hi Donny😊 Do the late 046 (2003) have the ignition limiter? Btw love your videos✌🏻 Best regards Henrik. Denmark Europe🤟🏻
@donnywalker4691 Жыл бұрын
No they didn’t hi there in Denmark 🪵👍
@hjvilhelmsen8848 Жыл бұрын
Do you know how i should set the carb? L and H? I run a bark box with a 21mm output port, and I have open the muffler inside☺️✌🏻