Dont buy i2c p14 pro!!!wasting your money and destroy or damage your nand ic using FORMAT REPAIR..

Рет қаралды 1,357

8 ай бұрын

Пікірлер: 44

@Jeffjedzac 6 ай бұрын

Actually i already done for that issue. Not because of the i2c p14 pro.. I change the nand ic and i read the system using unlock tool.unlock tool read the original nand data with wifi-bluetooth ethernet address..the truth of i2c p14 not all of the nand is supported and poor box..much better to buy JCID..

@jakkawutchaipoom8574 11 күн бұрын

😢😢 JC Best (i2c is not good at all) I made the mistake of buying the i2c 14pro. I saw your clip too late.😢😢😢😢😢😢😢😢😢😢😢😢😢😢

@mobiletech911 6 ай бұрын

after format repair flash sa itunes boss at write back via purple mode

@i2cMobileFixTools 8 ай бұрын

If you need to change a hard disk for your iPhone7, the operate as following Step 1: Put your old hard disk into the BGA70 P14pro - P14pro connect with the computer - open the I2C software - click “query disk information” - click “backup bottom data” to save your data to computer Step2: Put a new hard disk into the BGA70 P14pro - P14pro connect with the computer- open the I2C software -click “write backup bottom layer - install you hard disk to you iPhone 7. Using the flash phone software to flash your phone boot. But if your Hard disk been format repair, please install the hard disk into the phone, then using the flash phone to flash your phone boot. (Attention, please be careful during your disassemble the hard disk,don’t damage it, or install it well, or it won’t boot) Then take out your hard disk to BGA70 P14pro for write back up bottom layer - install you hard disk to you iPhone 7. Using the flash phone software to flash your phone boot. P14Pro Hard Disk Expansion Operation Tutorial kzfaq.info/get/bejne/jp9mh8qSztDKpY0.html

@zerrcarreon5491 8 ай бұрын

but we have already backup the bin file and try to reinstall it again on same hard disk. already have error

@Jeffjedzac 8 ай бұрын

I told you this i2c box and engineer is lying..i told so manny times..hahhhaha.much better engineer of i2c just make a video to prove that the function of hardisc format repair will fix the error or error 9 4013 in flashing..hahahah.

@Jeffjedzac 8 ай бұрын

I2c engineer did you see the reply or responce of the one customer that buying your products? Same of my issue..hahhaha.very funny box.wasting our money

@zerrcarreon5491 8 ай бұрын

Boss nka chat ko sa whatsApp di pwede mag format repair mahirap kausap paulit ulit nlng haha di ata maaccept yung error

@zerrcarreon5491 8 ай бұрын

Pero try ko i coordinate muna sa seller ulit

@Jeffjedzac 8 ай бұрын

I2c engineer said..iphone with error 4013.9 or 4013 during flashing is cannot be fix using i2c p14 box..i2c p14 not fix the error of nand ic using the nand format repair..it means is not working properly this box😊

@ac-technician3506 8 ай бұрын

if na format repair mo idol need pa ata eh install mismo sa board then flash sa 3u after sa restore pwede na sa purple mode para ma write yung back up files. sa pagka intindi ko lang

@ac-technician3506 8 ай бұрын

tested kuna sa error 9 / 4013 😊

@Jeffjedzac 8 ай бұрын

Un din ang ang pagkkaintindi ko.hahhahaha.slamat.mmy or nextday ttry ko po.asa duty pa ko

@zerrcarreon5491 8 ай бұрын

Pano kung deads na yung phone

@i2cMobileFixTools 8 ай бұрын

@@zerrcarreon5491 Charge the phone full of electricity

@togka9328 12 сағат бұрын

Buti walang error sir kahit burado ang partition ng nand dahil binura ni p14 pro. Need insights po sir. Kase yung saken nag 4014 po.

@Jayveepaddayuman-fk8fj 4 ай бұрын

Ok ba p15

@zerrcarreon5491 8 ай бұрын

Dina tlga pwede boss hahaha dinila ma accept na masisira tlga yung hard disk

@zerrcarreon5491 8 ай бұрын

Boss same rin sakin

@Jeffjedzac 8 ай бұрын

Gago yang engineer ng i2c..

@zerrcarreon5491 8 ай бұрын

@@Jeffjedzac gusto ko sana i return ulit sa seller eto p14 yung sayo ba boss matagal nayan?

@i2cMobileFixTools 8 ай бұрын

@@Jeffjedzac you did not doing operate in right method.

@trendong5510 8 ай бұрын

anu maganda lods na nand programer?

@Jeffjedzac 8 ай бұрын

S ngayon jcid p13.. Yang i2c abnormal function yan..ung mga my error tulad ng error 9 .4014.4013 hindi narerepair ng box n yan.nag email nko s knila hindi nmn nila masagot..