👇WeldTube Store👇 www.weldlife.com

RMD really shines when welding in a positioner. Our company in Ky purchased the first two 400’s in the entire region. We quickly developed a couple of WPS’s, certified a dozen or so employees, and set up a nice prefab operation centralized around a couple of 400’s. No doubt, the absolute finest machine I’ve ever used, Stick, Tig, dual Mig.

WELD TUBE FOR ALL BEGINNERS IS A BIG THING .. THANK YOUUUU SO MUCH

You adjust the trim until the arc adapts to how you like to weld. When it sizzles, pick up the pace a little. Your pauses on the side are just a tiny bit longer than what your trim is set for. Open up the arc, (raise trim slightly) until the sizzle stops. The goal should be no sizzle. Looking good guys, thanks for demonstrating an incredible machine!

The vice grips to brace your arm is clutch. Glad I seen this 💯

I am really starting to like those pulse mig welders ,they do a such a great job on steal and aluminum with not to much splatter.

👇Learn more about Miller PipeWorx 400👇 www.millerwelds.com/equipment/welders/multiprocess/pipeworx-welding-system-m00326

Great Tips!!!!

First fab shop I was in had Phoenix 456 power source w dual wire feeders. 0.35” short circuit with blue shield 8 for the root & 0.45” Pulsed Mig with blue shield 23 for the fill/ cap. They upgraded to Pipe Pros & again to Pipe Worx . Always with dual feeders. They went to flux core for the fill and caps after a while. More forgiving. We rolled everything we could. About 45-55 mins. for a 24” std wall joint using the pulsed mig.

Totally stealing that trick at 1:14 for my restarts at work🤣 Been contemplating how to get a good tie in lately

Awesome 👏 👏👏

This was just a flat out awesome video guys! Need more content like this. Nice chaps Travis!

Hey raza ...q perrones la neta....saludos desde Veracruz Mexico.... congratulations... way to go👍

Nice video job 👏

Is awesome... Good joob bro!!!

Best channel to learn hands down 🙏💯🔥

Good job

real impressive

What was your background arc settings at? You have to hold the left or right gun selector button down for a few seconds, to get the display to change from “arc Length”to “arc”

I'm not sure if I missed but what wire speed and amperage were you running the pulse mig?

Best channel

Love your videos man!!!! Been a welder for 18 years and have learned quite a few tricks from your channel

Funny watching these guys prop on everything...

Thanks guys

What did you guys have your arc control set at?

Awesome job Rosendo and Dakota makes me want to try that RMD now!

Should try it with 0.45 wire 🤔 would like to see it done more than the .35 since most shops where I'm at only use .45

Let's have some metalcore on the pipeworx

Nice work fellas 🤜🏽🤛🏽🔥🔥

7:09 What’s that in his pocket? 😂😂😂

You guys have a video of 6g schedule 80 test with pulse?

Great video guys!!!

I run my machine 21.5 380 on 16 ga pipe. But what do I know?

Can you make a video of dual shield on pipe in position?

What is your voltage for 185 and 210 wire spd😊

What gas was being used ?? 90/10 ?

Your weave is too narrow giving a nice tough weld, your root is not oxidised enough and I am well impressed with the edge at 11:30 @ 13:21. Nice looking dead straight edge there guys, well done.

🤝

Hello brother I'm a welder I need you help please I need some information about RMD welding.

Salam dari Indonesia bang🤟🤟🤟

Felicidades Amigos

Is Miller building any new machines? I was Rolf by a vendor that Miller hasn’t had the components or staff to build any equipment for some time now.

I once did a pulse fill and cap on 14” pipe in 5G position

More accurate would be 9 o'clock to 6 o'clock 2nd root pass then 12 to 9 or 3 to 6

Boa Noite amigo sao os petroleiros engenheiros 😊

Good morning sir

can we get more pipeeworx content???

😁😁😁😁😁

What does RMD stand for?

You boys better not be wearing and lincoln apperal in a miller shop...lol good video

Tulog na beng kay natuyo ko

Queria ver al chingon de la película soldando TRAVIS

Do the same with a normal mig set 😄

What's RMD?

Покажите на каких параметрах варите от корня до облицовки🙄

Nice machine what is the cost?

Jeeeez that is one ROUGH cap, it looks like hammered dog sht 😂

Travis ,il filo animato è sempre migliore per il riempimento e le finiture

i like the the root and fill. I'm old pipeliner from Canada if i put a huge wide weave cap like that on joint Q.C would run my ass why is it ok ro weave with these guns but not stick?

Real welders go uphill

Random question What does the Term SIG and SIM mean? In welding terms?

RMD…… Short Arc on Steroids 👍👍

Can you start putting settings pinned in the comments

Başarılı

Jhon moryson WWA surstar

Can you do a pulse downhill?

Go cowboy boots, proudly rolled in on a hardly gayvidson. Lol

Give them boys some 6010 and low hi.then top it off with 8010.

Please active the subtitles of whats you talking about while to wheld. Somebodies need to take notes to understand completely and learn better specially in thirds world bro...

root mode rmd miller is a 👎!! in the ceiling can not push the return roller!! And this is a fact. As for the pulse mode, did you guys overheat the pipe? what about the near-seam zone?

when your giving these “tutorials” and giving “advice” it always drives me nuts!!! It might just be me being a dick but i want to make mention that the parameters in voltage, wfs, actual travel speed, shielding gases, and fit prep etc etc are all variables that need to be checked and adjusted per the WPS and PQR’S and so forth which employers CAN and DO have that are specific to code and Employer/client. All that being said i just think its worth mentioning to your viewers that they should always verify and double check their processes & procedures before just running with these tips. and if they dont understand what all the stuff means tell them to make someone explain it and teach them so they can be more competent and hopefully pass on the knowledge to the next

I have to say I love my Miller Digital Elite welding hood. But after getting the 3350 Lincoln Viking I just can't go back. But with that said Lincoln welding machine absolutely suck and I absolutely love my Millers. Unfortunately the company I work for uses Lincoln

Not a good video if we can see the actual welding.. 🤔

Those setting produce a completely erratic arc, nothing but crackling and shit flying everywhere, on all the pipe worx 400 at my shop, same guns, same gas, same wire, people from miller showed up so we could ask them about setting, hey what does this arc length and arc settings do? All they said is it just changes variables, they didnt know what they actually did, just changes things, what complete letdown for such a whats supposed to be a great machine

90/10 doesn’t sound like that. 75/25 does.