Good stuff. Thanks for posting. Gives me the confidence to use this the first time and not fear I'm going to screw up.
@SergioSilva-zc6id4 ай бұрын
I discovered this video a few days ago and it helped me 100% to do paint touch up on a lot of chips on my wife's car, many of them pretty deep and it came out really, really well. Thank you for your content, you have one more viewer subscribed to the channel.
@fartamplifer Жыл бұрын
Dr. ColorChip always sends only one glove.
@TurnerMobileDetailing4 ай бұрын
Wonderful, thank you!
@imhann9811 ай бұрын
Wonderful and very informative, well done my friend👍
@EpicNinjaRides Жыл бұрын
They have a squeegee that would make that much easier to level
@cossamaximus87702 ай бұрын
Why dont you sand down inside the chips firts to make it a smoother transition between the chip/scratch and the surrounding paint, like in your previous video wouldn't have it made the scratches less noticible?? Thanks
@TurnerMobileDetailing2 ай бұрын
No you wouldn’t want to risk scratching the surface outside the chip while sanding, and sanding isn’t recommended by the manufacturer. Also sanding a rock chip is really only necessary if there’s rust present imho.
@deanhart8154 Жыл бұрын
Well done, all the best!
@rizingplanet4 ай бұрын
Pait should be applied next to the chip. This drags the paint into the chip. Depositing directly into the chip will enable the paint to pull out of he chip when you squeegee. Compare to the Dr. C factory tutorials. He still did manage to get an okay result .
@MBauer-op6vx5 ай бұрын
Awesome video, very clear instructions, thank you! Quick question, I need to do a 2 stage paint correction on my car as well. I was thinking do the first heavy cut round, THEN Hit my paint chips with this kit, then start the second stage (light correct/polish) and seal or coat after the color chip regimen. Thoughts or recommendations? Thank you!! Again, great video!
@TurnerMobileDetailing4 ай бұрын
Thank you! Honestly is probably doesn’t matter if you fix the chips before or after the final polish. As long as you do the repairs correctly. I’ve let this stuff dry too long before and it’s very difficult to get off once it’s cured, even polishing didn’t take it off. So just follow the instructions and if you feel it would be best to use it before the final polish then give that a shot.
@lernmor2137 Жыл бұрын
Isn't it best to clean, clay bar, iron remove, etc, polish the paint, and then apply this? I'm also wondering if a polisher will remove the repair even after it cures?
@TurnerMobileDetailing Жыл бұрын
Not really dude. You can do all that if you want, but the only thing that affects the chip really is cleaning it and the surface around it. Once cured, it should be fine to polish.
@ChrisTashjian18 сағат бұрын
if the chip on the bumper has rough edges, how do you smooth them out? Some 3000 grit sandpaper?
@TurnerMobileDetailing3 сағат бұрын
I would use the sanding tip on a paint pen
@rizingplanet4 ай бұрын
And put the drop of paint next to the chip And the squeegee will level the paint into the chip instead of smearing it out
@AlmX001 Жыл бұрын
Nice video. I'm getting my car cleaned and detailed in about 5 days. Do you recommend doing this before or after the detailing?
@TurnerMobileDetailing Жыл бұрын
Definitely before any wax or coating is applied.
@JohnnyReno7111 ай бұрын
Is this a one time use ? Or can you reuse the product at a later date. Brush , towel by cleaned for a future use?
@TurnerMobileDetailing11 ай бұрын
Yes, the kit can be used for quite a while, and yes you can clean the brushes and applicators with a little solvent before storage.
@JohnnyReno7111 ай бұрын
@@TurnerMobileDetailing wish I saw this video before I bought a paint pen. I just have a few chips and used a paint pen and it came out clumpy.
@alfredo917311 ай бұрын
Thx for sharing. Do you think a bit of wet sanding over the protruding paint provided, could be a solution instead of using the blending solution?
@TurnerMobileDetailing11 ай бұрын
Sure if you’re confident in your wet sanding skills. Either way to get the paint flush you need a rigid backer to the blending towel or sand paper, like rids stix
@UzumakiX5series6 ай бұрын
I have used 2000-2500 grit 3M sandpaper before and it seems to work fine. Although I let it cure for 30-45 minutes before wet-sanding. Like the author mentioned rids stix is necessary to make it sure it's level because our finger is uneven.
@SWACBUZZ Жыл бұрын
Is black easier to do? I have tuxedo black paint.
@TurnerMobileDetailing Жыл бұрын
Black is probably the hardest actually since black shows any little defect more than other colors. You’ll have to take your time with it.
@markbell548310 ай бұрын
Read the instructions
@dominicklombardi839 Жыл бұрын
Can I use the dealership vin number touch a paint that I already have?
@TurnerMobileDetailing Жыл бұрын
Probably not with this system
@BLR1GBattlemaster11 ай бұрын
Dr Colorchip was a huge waste of time for me. Didn't do anything for some deep scratches, and infact made it look worse since the color looks really bad once the solvent is applied. I don't understand why people keep pushing this garbage.
@836dmar2 ай бұрын
I’ve never used this stuff but with anything paint there are so many variables and the techniques one uses are a majority of those. Unless the actual paint formula is damaging to an existing finish it is most likely just the way it was done.
@dfboilerАй бұрын
Agree, its okay for the 10ft view, but if you have deep rock chips, you need to fill, sand, paint and clear coat, no amount of dr. color-chip is going to fill those and look good up close.
@bryans279010 ай бұрын
I want to do a polish and ceramic coat.. should i repair stone chips first or after? Worried the polishing will take off more paint
@TurnerMobileDetailing10 ай бұрын
Before. Polishing will not remove this stuff if applied and cured properly. Give it 23 hours to cure before polishing.
@exil3dlivecomАй бұрын
White os extremely forgiving
@exil3dlivecomАй бұрын
Hey, once the touch up hardens fully after a few days, can it be wet sanded a little to Level it even more precise?