Drain height shower pan. Bonding flange

Рет қаралды 5,937

6 ай бұрын

SUBSCRIBE Learn how to tile the right way.
How do you determine the height of the shower drain in a bonded shower system that uses a bonding flange. In this case a FloFx drain assembly. In this video I show you how to figure out how to find the height of the mud for the sower drain bonding flange. All tile installed by Sal DiBlasi, Elite-tile Company, in the Boston North Shore area. This video contains affiliate links, which means I will receive a small commission if you click on the product link. #tile #transformthetrade #howtotile #installingtile #howtoinstalltile #liticrete #mapei #Schlutersystems #diy #construction #ardex
👉 👉 👉PDF Floor installation guidelines sowl.co/s/wWd2d
Free PDFs 👇👇👇
Leaking Shower? sowl.co/5oAfm
Find a Contractor sowl.co/s/jtgoa
Failure Spot Bonding sowl.co/ZvQBH
🙂 This is my Amazon Store 🙂 www.amazon.com/shop/saldiblasi
🌲 Link Tree 🌲
linktr.ee/saldiblasi
☕ Buy me a coffee ☕
www.buymeacoffee.com/saldibs2
📷Camera Equipment 👇
DJI Action 2 Power Combo amzn.to/3xA5fMH
DJI Action 2 Dual-Screen amzn.to/3Qvk8IX
DJI Pocket 2 Creator Combo amzn.to/3mUr1pu
👇 Some of my favorite Tools 👇
Float amzn.to/2tdEpN2
Rubbing Stone amzn.to/2QrgRfh
Notched Trowel 1/4 x 1/4 x 1/4-inch amzn.to/36bq5mQ
Notched Trowel 1/2 x 1/2 x 1/2-Inch amzn.to/2Q5e90g
Notched Trowel 1/4 x 3/8 x 1/4-Inch amzn.to/39j1caB
Super Dust Collector - WaleTale amzn.to/2MDuVkK
Black Nitrile Gloves - 6 mil amzn.to/2SJQ6FZ
Margin Trowel amzn.to/352MYHx
Mortar Mixer amzn.to/2ZxYqtF
4in Sandpaper for Stone Polishing amzn.to/2ZB2skT
Polishing Rubber Backing Pad amzn.to/2srikdy
Montolit 63P3 24 Inch Tile Cutter amzn.to/2MDoFt l
DEWALT Wet Tile Saw amzn.to/2QqpO8O
Rubi Thinset mixer amzn.to/39VmNWV
Grabo Pro Lifter
amzn.to/3BBO5ys
IQ 7" Dustless/Dry Cut Tile Saw IQ228
amzn.to/3wFE3w0
Opt into NTCA’s VIP Text Messaging program for training opportunities. Text “NTCA” to 31996 or Visit (For Industry Professionals only) widget.smsinfo.io/v2/ae58812b...

Пікірлер: 35

@rideauviewconstruction717 6 ай бұрын

Forever grateful for Sal’s videos. Helped me establish skills needed for building showers and tile work. No failures since starting up in 2009.

@SalDiBlasi 6 ай бұрын

Thanks, glad it helped

@TILEROB 6 ай бұрын

Ya he git a good channel

@323floors2 6 ай бұрын

You seem to be the one guy who cares more for the industry than he does being an influencer.

@SalDiBlasi 6 ай бұрын

😊👍

@billyc5010 6 ай бұрын

I've watched probably every single video of Sal building a mud pan, it never gets old watching the best in the business effortlessly build another perfect project. Thank you Sal for continuing to share your expert knowledge with us.

@SalDiBlasi 6 ай бұрын

Wow, thank you!

@TILEROB 6 ай бұрын

Good video

@chengsu6499 5 ай бұрын

The hole on the subfloor is much bigger than flofx flange drain outlet, so there is a gap between the outlet and the edge of the hole. Do you fill the gap up? Or will the gap cause mud bed movement in future?

@felixcarrillo1528 2 ай бұрын

I think this drain is good but it needs a hair cather like Ebbe drains, also the finish grout around the drain is prety thick or wider than the grout on the tiles

@BonBon770 6 ай бұрын

Good video! I always tape off my bottom piece with duct tape and cut it really nice to keep all the mud away from the drain. should that be done with bonding flamges to keep the mud off of the actual felt until you're ready to connect the actual membrane to it? And if so, which tape would you use?

@travisk5589 6 ай бұрын

Sal, level those from diagonal corner to corner, it will be faster

@SalDiBlasi 6 ай бұрын

😊👍

@WadeMD 6 ай бұрын

Sal, im a DIYer. I see that you use multiple different systems, kerdi, latticrete. What would you recommend as the easiest system? I’m planning on doing a mud base slope to my drain and waterproofing and then tiling.

@skdrcr 6 ай бұрын

Appreciate you Sal for making this video. Is your target drain height 1 1/4 in? What if you were on a concrete floor, would the height be less?

@SalDiBlasi 6 ай бұрын

Usually the same, but depending on the type of mud, could be less.

@ohokayofficial 6 ай бұрын

3 bathrooms I’ve been to so far (this month) have had their drains situated flush with the wooden subfloor.. Any tips for what to do in prefloat situations - can you still prefloat or does the drain have to be redone?

@SalDiBlasi 6 ай бұрын

I am guessing those were two stage drains, not a bonding flange type like the ones I use. They should have a preslope, liner and then final mud bed. Bonding flange has a single mud bed.

@ismaelcarrerojr7124 6 ай бұрын

Hey Sal what type of screws you used to hold down flange? Thank you again.

@SalDiBlasi 6 ай бұрын

They are laticrete screws, the head is a bit smaller than the durock screws.

@ismaelcarrerojr7124 6 ай бұрын

@@SalDiBlasi thank you for your quick response

@Paul-rg4is 6 ай бұрын

What material is on those walls? Are you putting sheet membrane over that?

@SalDiBlasi 6 ай бұрын

New waterproof board, not available just yet.

@jodavis1981 3 ай бұрын

Sal I see screws in your cement board lower than three inches above floor, is that ok? I always hear people say dont embed screws in mud bed. Your thoughts?

@SalDiBlasi 3 ай бұрын

This is a bonded system has no effect on waterproofing.

@ryankelley85091 6 ай бұрын

What's the minimum mud depth under the drain flange if working on single sheet of plywood sub-floor? I'm trying to go curbless. I have 1.5 inches of difference between the shower and the rest of the bathroom floor. The shower 72 x 38 inches, which gives me about 32 inches the long way to each wall from the edge of the drain flange. That would put me right at 1/4 slope per foot if the top of the flange is 3/4 inches off the floor. I'd have to go less than 3/4 inches of mud under the flange to make this work.

@TsiRoadkill Ай бұрын

You want a inch of mud there but you could get away with like 7/8 and 1/8 per foot slope

@ajrotko 4 ай бұрын

Do you do anything to prevent mud from going in the hole of the subfloor?

@SalDiBlasi 4 ай бұрын

If the hole is the correct size, it's not a problem

@thomasrose6629 6 ай бұрын

Do you have anything against slurry coating the floor before the mud instead of tar paper/wire when you’re waterproofing it anyways? Or is just a personal preference?

@SalDiBlasi 6 ай бұрын

Supposed to be an unbonded mud bed on plywood, bonded on concrete.

@Losas.Company 6 ай бұрын

@@SalDiBlasithe drypack youre using, where from? What brand?

@erikleibbrand9648 6 ай бұрын

Hello. I know it's overkill, but could I theoretically put a oatey pvc pan liner in and then put a membrane over the mudbed, if i could find the right parts to fit togather?

@SalDiBlasi 6 ай бұрын

Don't do that.

@erikleibbrand9648 6 ай бұрын

@@SalDiBlasiOkay.