Dual Mass Flywheel & Clutch Kit Install - Bmw 3 Series E90 2005-2012

Рет қаралды 92,274

6 жыл бұрын

Bmw E90 3 Series with a noise coming from the transmission at low speeds. In this video I give a overview on the replacement of the clutch & DMF.
Thanks to everyone who watches my videos, likes and or leaves a comment. I appreciate everyone of you.
Thanks for watching :)
➢ For business enquiries Email : Burkesgarage01@gmail.com
➢ Our workshop location is Kilmaine Village, Co. Mayo, Ireland

Disclaimer:
GerardBurke is a qualified motor technician who has completed modules & courses in manual handling and all aspects of workshop safety. These videos are not intended to be used by anyone who is not trained and or qualified to carry them out.
Due to factors beyond the control of GerardBurke, I cannot guarantee against improper use or unauthorized modifications of this information. GerardBurke assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. GerardBurke recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of GerardBurke, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not GerardBurke.

Пікірлер: 40

@zippymo672 5 жыл бұрын

Thanks for sharing. I have the same problem with my BMW E90. It's getting changed tomorrow.

@genuinemonkeyman 8 ай бұрын

Come across your video, and that's exactly what I have with my X1 2ltr d xdrive, thanks mate 👍🏻

@AustinTillison 5 жыл бұрын

Awesome video, thanks Gerard!

@noobontour3167 3 жыл бұрын

do you get the tool to center it or how may u get hands on one, or does it self adjustable?

@serbcristian2136 6 жыл бұрын

You have used the old bolts for the pressure plate ?

@michaelaguilar3601 3 жыл бұрын

What is the torque specs for these bolts? Thanks in advance

@-smp-scientificmethodpersp838 5 жыл бұрын

So the pilot bearing does not need to be removed from the crank or reinstalled to it. You just put the flywheel in with the bearing in the flywheel, so no need to worry about pilot bearing removal or installation for this job.

@B2KJFF 3 жыл бұрын

How much would this be to do on my e90. For parts and labour ?

@JacesPlayhouse 6 жыл бұрын

Great Info! Nice Car too!

@moekakke 2 жыл бұрын

Have you placed a reinforced clutch ? And does anybody know a link to buy a performance clutch for the N57D30A engine ?

@teodormihai2244 2 жыл бұрын

Any li k with the allignment Tools for clutch ?? Thank if you will answer to me

@sibisogno 2 жыл бұрын

From start to finish, how long did it take you to remove and then fit all that stuff? I need the same doing to mine, gonna order the kit, but I will get my garage guy to fit it, would be good to get a rough idea how many work hors it needs... BMW's never stop costing money.

@kriscoombe3415 Жыл бұрын

Hi mate where is best place to purchase this item (flywheel/clutch) cheers

@dualmassflywheeldmfrepair5370 4 жыл бұрын

very good one more registered and will like

@georgejexter Ай бұрын

Can you get away without using the centre tool?

@davidwelsh1517 5 жыл бұрын

Do you need one of those self adjusting clutch tools to bolt on the pressure plate or does that locking ring you could see in the new one mean you can just bolt the plate straight on then release the locking ring?. Thanks .

@danielbrooks7522 4 жыл бұрын

Also interested, it looks to be already pre tensioned hence the 14mm Allen key plate holding the springs down??

@davidh9659 4 жыл бұрын

Thx! The rattling sound you described: Is it only when partially engaged or does it occur when the pedal is fully released (clutch engaged) too? I have a strange rattling when accelerating at low RPM (1000-1300), as if the exhaust / heatshield or some sort of sheet metal were resonating / hammering into something else. Start from a standstill is jerky as well.

@stephenfarrell1240 3 жыл бұрын

I have now. Was it this can u remember ?

@AlluApplepie 3 жыл бұрын

Same symptoms in mine! Did you solve this? Booked a dmf+clutch replacement for mine, hoping that will be the fix

@vereshchak9219 5 жыл бұрын

What model 3 series was this with the 8 bolt flywheel? N52 or n54?

@TheSonyjoseph 5 жыл бұрын

N47 2.0 diesel.

@mfingokomisa4698 6 жыл бұрын

Hi Gerard I'm hoping you can help, I own a E90 BMW 2006 model and recently had the clutch kit changed. the problem is the car won't start. I'd just like to know if you may know what could be the reason and how to fix it.. Please help

@GerardBurkeBurkesGarage 6 жыл бұрын

Are you saying the car was starting before you started the clutch job and once it was complete it doesn't?

@liviu271 Ай бұрын

Starting the car is nothing to do with the clutch! Check your starter and injectors and fuel pump ! One of them at fault 💪 good luck

@keith7564 3 жыл бұрын

Can a bad flywheel cause a bmw to loose power aswel

@FrankDisseldorp 2 жыл бұрын

No it can not. The clutch can make acceleration sloppy as it will slip. A worn flywheel will give you noise, vibration and in the end you cannot select any gears.

@99ron30 2 жыл бұрын

Have you had any experience fitting a solid single mass fly wheel kit to an E90 320d?. My 2006 needs a flywheel and clutch and the SMF kits are pretty much half the price of a DMF kit, some people say they are fine, some people say not to do it. I don't have much money to put in to the car, I can tolerate abit of extra vibration aslong as its reliable. What do you reckon? Cheers.

@federicotorresbordils7624 4 жыл бұрын

Hello Mr. Burke, Which aftermarket brand did you use ? Do you know who is BMW supplier for OEM parts for clutch and dual mass? What brand GEAR OIL did you use to fill the gearbox? Will be very useful Comgratulations for your channel BimmerN53

@reeseboi8704 4 жыл бұрын

The aftermarket brand he used was LUK. Not sure if they are a direct oem supplier but Sachs and Valeo are and they have their own flywheels and clutch kits for this model.

@dazthephot 5 жыл бұрын

That's exactly the symptoms my 2006 e91 with 152k is showing. How much was that job if you don't mind?

@ibrahimahmed5017 4 жыл бұрын

Usually costs £500

@goognamgoognw6637 5 жыл бұрын

I had brought my complaint with bmw NA : "rattle near clutch engagement point in 1st gear , jerky car" and they refused to do anything about it, claiming it was normal. I came back complaining about it a second time and the bmw regional engineer also rejected my complain (avoiding to meet me) and sent me an email that "clutch are a wear item blah blah" when clearly it's a DMF issue, not the clutch. Especially since my car has only 25k miles and bought factory new by me, they are liars to refuse to fix it. Now my warranty expired and i don't know what to do. I want to bring it to an indy store (to diagnose it) then sue BMW NA. I already got testdrive opinions from independent mechanics all said, something is wrong with DMF. I even said so to the bmw dealer, the bmw mechanic laughed to my face saying BMW NA does not care what indy mechanic have to say.

@technopro-kz4xv 6 жыл бұрын

take out your CDV (Clutch delay vale) you will feel the difference changing gears... 👍You can thank me later 😉

@GerardBurkeBurkesGarage 6 жыл бұрын

Are you speaking about this job or in general to people that may be looking? The finished work on this made the gear changing like new again. certainly no need to remove any other components in this job.

@DJorDJeDJ 6 жыл бұрын

I got the same problem, judder when taking off in 1st gear, took CDV off and replaced with modified one, but it didnt cure the problem, and while at the mechanics, noise comes when clutch is di-pressed, definitely bearing noise, but hoping dual mass flywheel is fine as its gonna cost a bomb to replace it

@deejarvisful 4 жыл бұрын

Already have. Much better. 😀