That's a very helpful video as many are under the impression that it plugs-into one of the double cluster wire on top of the actual servo connector. I've installed a DUC-EE as well. However, unconfirmed revelation suggests that the exhaust valve only closes when in neutral. If true, that would make the DUC-EE useless for sound or performance. It would only be useful for preventing the valve from corroding shut or partly closed.

if your leaving the valve and standard exhaust on you need to lock wire the valve in it's open position, not left closed 👍

Thanks man. The generic instructions weren’t cutting it!

Great video! Excellent guide for eliminating the exhaust valve. Thank you! I am toying with installing a de cat pipe, but will see how this works for now. Thank you!

Thank you for the very helpful video, I was able to install the emulator in 5 minutes. Perfect!

Wow!! Very good!!!🎉🎉 What functionality does this device have? Sound? Performance? Is the exhaust valve always open after installing the servo emulator?

I finally got around to doing this on my 2016 PP. I didn't bother with a before/after video, but I can say that there's a clear audible difference here above 4K RPM, sounds more throaty and less wheezy. Removing the cat will completely change the sound profile, and this mod gets you a little closer to that profile since decat removes the servo. So I'd say it's worth it, as a foolproof cut and dry mod to your bike. Will it increase performance? No, not really. this is more for the audio gains IMHO.

Thanks for posting, going to put one on my Ducati Hypermotard 950.

Great video. I heard the gizmo doesn't work on the DVT multistrada. I take it all ok? The other point is my multi DVTs flapper valve tends to seize up. So recommended you apply some grease to keep it moving should anyone want to return it to standard. So annoying when it throws the check light. Have to lube it do 50 miles to release and check light goes off.

Great Video!

Thanks for the clear instruction. I have a question about the driver seat. I have the Seat in the high position. When I put the front of the seat in the guide, the back of the seat is too high and doesn’t rest on it’s points. It moves a fair bit when I take place on the seat. I need to flex the seat to allow a proper fit. It only seems to fit with the 2 front guides on top of the plastic slots, but then my seat is basically loose and anyone can take it off. Is your seat the same ?? Thanks.

Hi, how long did you use it like this ? Did you regret it after a while or still using it? Does it affect the bike like more fuel consumption or losing power at high speed?

you can just remove the steel cable from the butterfly valve and you will have the same result for free ... what is the point

In the original situation when you open the throttle the servo opens, however in your after video the servo seems to be in closed position?

So do u think if I order the competition werks Ducati Servo Eliminator for my 950 SSS it would work on the stock exhaust ? Louder ? Or is this only for a aftermarket exhaust? TIA 🙏

I unplugged the servo to harness connector. I never received a check engine light. I did get a servo fault code, but erased it no biggie. I have a 15' diavel carbon red.

Great video, do you think this will work on a 2020 monster?

I have a 2020 950s Multi are the fitting instructions the same for that ? or similar thank you a great Video

Are you liking it?

Hello. Interesting video. Q1. Where I can get the detail drawing you have shown pls?! Not sure if I want to install the emulator. My flap valve stack last summer, under warranty they cleaned and reset the fault lamp. Now is stack again, expired warranty a month ago and I was requested £90 to clean it again! Q2. Once I clean the valve and I see it open, I believe the fault lamp would stay on. Do you know I to remove it (not in permanent way, as it may report if happen again) Thanks in advanced

Hi, just install the mod plug-in and that's it? Or is there anything else that needs to be done with the cables or the valve? thanks

have the same bike but hav cat delete install .. have install the Vizi tec servo eliminator still have check engine light on do i needed to reset computer?

Where can I get an eliminator for my 2013 Ducati Monster 796

My goodness, I wonder how much this whole thing weighs and if removing it would throw a code on my bike...

Can provide the link on where to buy the servo eliminator....pls thank you

Hi, why not just disconnect cable from valve. Is there reason not to

Does it eliminate the flat spot at around 7000

29 or 39 bucks?

Or simply unscrew the flapper valve, cost £0

ummm just undue the cable as the valve is sprung open anyways. Worked on my 2019 PP