Dust masks Compared

Рет қаралды 17,221

Күн бұрын

You need a good dustmask! Here’s an overview of a few different options, focusing mainly on a comparison between the JSP Force8 half mask and the Trend Air Stealth

Пікірлер: 56

@iestynd 5 жыл бұрын

I love the comment about the beard and the wife! I only have stubble because she told me she likes how it looks!! Great honesty! Good work. Thank you.

@Alastair_Freebird 5 жыл бұрын

Iestyn Davies thanks for commenting! 👍

@kevinvanzanten2194 2 жыл бұрын

You have a great ability to explain and inform in a way which is clear and concise. Great work

@Alastair_Freebird 2 жыл бұрын

Thank you!

@StuffUCanMake 5 жыл бұрын

Thanks for the tip. I Use MDF a lot and I needed this safety reminder.

@308sir 3 жыл бұрын

What kind of filters you recommend me using for this trend mask I work in a plastic grinding Room not a lot of air flow it gets really dusty

@sulaymanhaq5630 3 жыл бұрын

Great video mate , I didn't even know about any of these , I was quite the fool when I started to wear one at first , didn't check the seal or anything - albeit I wasn't doing anything too dangerous - just grinding up some herbs for a blend , but it seems without checking the seal and such I might as well not have worn the mask since I was breathing in the dust either way ! Keep up the good work mate.

@mariacroxall 2 жыл бұрын

Very useful! Thank you so much!

@Alastair_Freebird 2 жыл бұрын

Glad it helped!

@Fredwitrave 3 жыл бұрын

Thanks. That was very informative.

@Alastair_Freebird 3 жыл бұрын

Fredwitrave its always nice to get a positive comment on an old video, thanks!

@johnmccabe8355 5 жыл бұрын

Good review Alistair. What masks do you use when painting. I took your advise and got in touch with Movac with a view to ordering some Sayerlack.

@Alastair_Freebird 5 жыл бұрын

Hi John, let me know how you find the Sayerlack paint, I don't think you'll be disappointed. I got a half mask for Brady for spraying, from the Movac range but pretty similar to the JSP half mask, it just seemed appropriate to get one approved by the spray supplier! The truth is I do very little spraying myself, although I will have an opportunity to brush up on it when Brady goes away for a couple of weeks in June!

@Vinyl-Sloth 2 жыл бұрын

All the issues with the JSP I found with the stealth, so got the jsp horses for courses I guess

@jamesbailand4311 5 жыл бұрын

Canny. Interesting that some of the issues I've had as a first impression on the trend stealth are all worse on the JSP mask. Good to know! ...I've a close beard and the trend mask gets a canny seal.

@sauceonsauce1808 Жыл бұрын

Is the stealth mask good for package dust? I have to work inside containers and it’s full of package dust, I got sick one time and got an asthma attack

@Alastair_Freebird Жыл бұрын

I think it would be yes but the important thing with any mask is to make sure it fits tight to your face so there aren’t gaps allowing the air and dust to get in without going through the filters

@nowthenad3286 3 жыл бұрын

Where do you get the cheaper filters from? Thanks

@Alastair_Freebird 3 жыл бұрын

Nowthen AD I think I’ve always got them from either toolstation or screwfix but we’ve been stretching out the lifetime of ones we already had in stock because I couldn’t find filters for either type of mask since covid (haven’t actually checked for a few weeks now though).

@jackfinnerty7891 5 жыл бұрын

Good video, I also use that trend one and I have a pumped one similar to the one you had but think mines branded evolution. Although they are the best ones I've worn so far I still hate them!! A couple months back I briefly looked into professional pumped masks where the pump clips onto your belt and pipes air up to your head! I haven't fully ruled one out but it went on the back boiler when I realised it was approx €1500 and I might still hate wearing it! Plus I don't think I could wear it when I go fitting as customers would be doing all sorts of wondering! I would be interested to hear your thoughts are if you've ever seen them? On a side note would you have any interest in sharing a copy of your ts&cs template with me? I really need to do one up and could do with some inspiration!! (i do very similar work to you.) As always keep up the great videos!! Thanks, Jack.

@Alastair_Freebird 5 жыл бұрын

Jack Finnerty drop me an email and I’ll send t&cs

@Alastair_Freebird 5 жыл бұрын

I don’t know anything about those pumped masks except aren’t they mainly designed for use when spraying with chemical-based paints?

@jackfinnerty7891 5 жыл бұрын

@@Alastair_Freebird thanks a mill will pop you an email shortly! As for the masks they make many versions. I'd be using it for spraying too but at that price you wouldn't ever want to take it off. I presume it's as good as you can get in terms of your health and of course no issue with sealing to your face as its pushing air out continuously. But I'm still concerned about comfort! In the warmer weather it'll b great as there's nothing worse than being hot and sweaty while trying to wear a mask! Also the fact it's full face or atleast that's an option you'll not only get protection from bigger particles but I'm also thinking that spraying and fine dust in general can't be good for your eyes! A lot to think about but health is the most important thing I guess. That said it's a lot of money for me or anyone to spend on a mask that understandably you can't test or try on before purchasing!

@jackfinnerty7891 5 жыл бұрын

@@Alastair_Freebird Hi mate, Just wondering if you got a chance to send that t&c template? I did email you but not fully sure I sent it to the correct address? Thanks, Jack.

@Alastair_Freebird 5 жыл бұрын

Jack Finnerty I don’t think I received an email from you?

@user-lm2pb1iw8z 4 жыл бұрын

I got force 8 with a2p3 jsp filters . Are these filters the equivalent of p3 / ffp3 protection for covid19?

@Alastair_Freebird 4 жыл бұрын

Ιο Ιοα honestly I don’t know

@chalky1150 4 жыл бұрын

The A, B, E and K denominations refer to the type of gaseous contaminants that respiratory filters are designed to protect the user against. To summarise: A (Brown) - organic vapours and gases with boiling points > 65°C B (Grey) - inorganic gases excluding carbon monoxide E (Yellow) - sulphur dioxide and acidic gases K (Green) - ammonia and organic ammonia derivatives Other vapour and gas filters are as follows: AX (Brown) - organic vapours and gases with boiling points < 65°C Hg-P3 - mercury NO-P3 - oxides of nitrogen CO - carbon monoxide P ratings identify a product’s protection against particles. P3 offers the highest level of protection. Whilst an AX filter would be more applicable to some products - such as WCP-2 and SKD-S2, as these also contain particulate materials - the A2P3 and ABEK P3 filters offer the best compromise as a combined gas/particle filter. Note that airborne liquids in the form of fine sprays and mists require a particle filter. However, particle filters do not protect against gas or vapour so, when using aerosols or creating an aerosol mist, a combined gas/particle filter, such as A2P3 or ABEK-P3 is recommended.

@Alastair_Freebird 4 жыл бұрын

@@chalky1150 Excellent information thank you!

@tomhancock6220 4 жыл бұрын

Have you tried the gvs eclipse?

@Alastair_Freebird 4 жыл бұрын

blue army no would you recommend it?

@tomhancock6220 4 жыл бұрын

@@Alastair_Freebird no I was looking at the masks at screw fix and I was trying to decide between the trend and the gvs, your video was a brilliant and when you mentioned you use the masks a lot in your line of work I thought you may have tried one since this video, thanks for the reply great video

@MrBishbashbosh2012 5 жыл бұрын

I had have one of the trend ones in my amazon basket, glad you recommend it. Have you any guys that use the small mask? If so how big are they roughly? Thanks

@MrBishbashbosh2012 5 жыл бұрын

Plus I struggled when using one of those full face snorkel things, beard meant I didn’t work grrrr

@waskito3443 4 жыл бұрын

I have the trend stealth and it's hard to breath through it

@rustybennineoneonemajesty 3 жыл бұрын

Get jsp mask

@FireAngelOfLondon 4 жыл бұрын

Thanks for covering this, protection is a neglected subject on a lot of KZfaq woodworking channels. They often advise wearing a mask or other gear but don't say anything about how to find the good gear. I had an acquaintance at one time who worked for the Health and Safety Executive, and he used to use that phrase; "A mask is cheaper than a new pair of lungs."

@danthechippie4439 3 жыл бұрын

Any issues with glasses fogging up with the trend mask?

@Alastair_Freebird 3 жыл бұрын

No I haven't had that problem, the seal over the nose is good

@richardwinters9723 3 жыл бұрын

The trend mask fogs my glasses, and I hate the hook clip on it.

@MyDavidlynch 3 ай бұрын

Mo for mohamad ..is it true they need 3bhours a day to pray many times ?? How do you find that works with a mohamad employee

@Alastair_Freebird 2 ай бұрын

Hi David yes observant Muslims do have the religious obligation to pray 5 times a day, but when you consider that it is done at dawn, noon, mid-afternoon, sunset, and late evening, then it doesn’t necessarily have to disrupt the work day much at all: if noon coincides with lunch break, and mid afternoon could even be just after the end of an 8 hour working day if the work day begins early. I think Mo probably wasn’t that strict about things, since I honestly can’t remember the subject even coming up with him and he certainly wasn’t getting a prayer mat out at lunch times or anything.

@lorenzocarcallas7141 4 жыл бұрын

where i can buy this item and how much....

@Alastair_Freebird 4 жыл бұрын

Lorenzo Carcallas unfortunately it seems to be out of stock everywhere at the moment! www.its.co.uk/pd/STEALTHML-Air-Stealth-Half-Mask-MediumLarge-_TRESTEALTHML.htm