No video
Dynamo testing on vehicle
Рет қаралды 56,465
Күн бұрынThis Nuffield is not charging so I perform a few simple tests to pinpoint the problem. If the dynamo does not spin at the first test, repair or replace the dynamo. If it does not spin at the second test repair the wiring.
@petersmall8402 3 жыл бұрын
Simple explanation on how to test your dynamo my Triumph Herald is now charging many thanks
@glennlingard7851 Жыл бұрын
One of the best videos out there, thank you well done!
@BuffaloLou Жыл бұрын
Thanks for the video. This'll help me to test the generator charging on my grey Fergy.
@LukeSchiralli 5 ай бұрын
Great video thank you, will help me to diagnose my 1960 Rover P4 80
@nathanrice1796 2 жыл бұрын
HAPPY TRACTORING - I like that one.
@seamuspurcell5065 4 жыл бұрын
very informative
@RaymondAuge 6 жыл бұрын
I love your videos. Very informative. I've watched most of them. I bought a 1953 (I think) 3/42 that runs great, had to replace the water pump and work on retrofitted hydrolic steering which doesn't work too bad. The remaining problem is that the main hydraulics which work, because I have a loader which uses it, doesn't seem to work for the rear linkage. I thinking I may simply not know how to use it and I can't find any details.. it may actually be damaged internally. I was wondering if you might do a short tutorial on using them so I can see what I'm doing wrong. Regardless, thanks for the great information ☺️ keep it up.
@montegoson 6 жыл бұрын
The 3/42 was made between 1961 and 1964. I have another video on the operation of the hydraulic linkage & the linkage lock have you seen that? There is also a lot of information at www.nufieldtractor.com
@RaymondAuge 6 жыл бұрын
montegoson thank you. I did see the video about the linkage and linkage lock. But what I can't figure out are the function and positions of two hydraulic control levers. But I'll look again at that site. Thank you. I'll report back 🙂
@RaymondAuge 6 жыл бұрын
So I tested the lock and it works perfectly. I also finally figured out the outer of the two levers on the hydraulic head controls the linkage in 3 positions: low=?draft control mode?, middle=at rest, up=raise linkage? (please correct me if I'm wrong) However I'm still not completely sure what the inner lever does. (you probably have figured by now I'm a tractor noob, but I'm learning ☺️, thanks for your patience)
@montegoson 6 жыл бұрын
The inner lever works the external outlet that is half way down the right hand side of the hydraulic casing, it it typically used for tipping trailers. The inner lever had priority over the outer lever so if that is in use ( raised) no oil reaches the outer lever!
@RaymondAuge 6 жыл бұрын
montegoson ok I think I got it. That would explain a lot considering the tractor is fitted with a front bucket running off the auxiliary hydraulic port.
@pedroreis195 4 жыл бұрын
Obrigado pelos seus vídeos, são muito instrutivos e necessários para quem tem maquinas mais antigas Continue a fazer vídeos
@JimF500 6 жыл бұрын
The bearing on your dynamo is a bit dodgy, I can hear it squeaking.Another way to test it is to connect a bridge like you have done, and run the engine at a fast idle, then connect a voltmeter at the large D terminal.If it reads over 12 volts, the dynamo is ok. Dynamos look nicer on engines , though not as efficient at charging though I think.
@montegoson 6 жыл бұрын
Yes I did consider the other test but it is more complicated and not good for the dynamo if they over rev it! Yes she needs a new bearing also, can get it done while I am doing the cylinder head.
@JimF500 6 жыл бұрын
Ah yeah, whatever works
@arwelagrimachinery 6 жыл бұрын
Thing is with a alternator conversion as well, every tom,dick and harry at a vintage show will point it out to you 😂
@bachandefi 2 жыл бұрын
@@arwelagrimachinery Mae hwnna'n gywir Arwel.