Easy Kingpin Install Tips

Рет қаралды 8,870

3 жыл бұрын

Kingpin install tips, freeze pin, light hone pin cylinder.
Keywords: F100 ccp disk brake kit king pin suspension new Ford

Пікірлер: 28

@scottr8063 5 ай бұрын

FANTASTIC you made this install easy for the novice 👍🏼👍🏼

@davidwood1923 Жыл бұрын

Thanks for Sharing... Any and All helps... I've Never had to Deal With These Things Before.

@inspectormando2958 5 ай бұрын

Great Help! That made my project go easy peazy!

@1mattbutch 5 ай бұрын

Lemon squeezy!

@kalebwalker5323 2 жыл бұрын

Big help thanks

@Sm-ne8ff 8 ай бұрын

Easy Man ! Thank you, some people think theyre So Mysterious !

@1mattbutch 8 ай бұрын

Groovy bud hope it helps!

@Sm-ne8ff 8 ай бұрын

@@1mattbutch Definately does ! Now if I can just find hydraulic pushrods and a rocker assy for my 56 Pontiac 261 inline 6...

@timothyfrost8807 Жыл бұрын

Excellent, excellent, excellent. Perfect timing, I've got a kingpin to replace on my '62 EPUP. Did you use the kingpin press to get out the old one, or do you have an equally outstanding trick for removing the pin ? Either way, thanks again, excellent video.

@1mattbutch Жыл бұрын

Thank you sir! If I remember correctly, I just used a BFH to remove it.

@timothyfrost8807 Жыл бұрын

@@1mattbutch I have an Italian speed wrench, very close to a BFH. Thanks again for this outstanding video.

@isaiah-lava5.086 Ай бұрын

Where did you get the replacement parts for the kingpins and other parts? Are they really that hard to get out?

@1mattbutch Ай бұрын

I wish I could remember exactly where, but I just did a search for 1970 Ford F100 kingpin kit and a lot of kits came up. And yes, it can be hard if there are rusty parts and old solidified grease. I got as much of the old grease off as I could and used easy off oven cleaner, heavy duty in the yellow can to clean the parts good then pressure washer. Use WD-40 to get the water out of everything, then some penetrant and a BFH should get it apart.

@VinceAikens Жыл бұрын

I didn't see you install the seal. Did it not have one the size of an oring with it?

@1mattbutch Жыл бұрын

You are correct, sir! That’s what I meant when I said at the end I was 98% done. In the video, you see the O-ring and end cap when I laid out the parts. I was just focusing on some quick tips to make the hard part of the job easier.

@ashleygates1235 Жыл бұрын

WAS IT HARD TO REMOVE THE SPINDLE OUT. I CANNOT REMOVE IT AFTER REMOVING BOTH TOP AND BOTTOM CAPS AND LOCKING PINS. SPRAY PENETRAING OIL ON LOCKING PINS OVER NIGHT

@1mattbutch Жыл бұрын

Hi Ashley. Do you mean the old king pin? You have already tried a bfh?

@ashleygates1235 Жыл бұрын

@@1mattbutch AFTER 2 DAYS SOAKING PENETRATING OIL, IT CAME OFF. NOW HOW DO YPU REMOVE THE BUSHINGS

@saulsifuentes3546 8 ай бұрын

How do you check to see how many shims you need at the top? I seen you used 2 but how did you come up with that number. Thank you.

@buttonysquare8501 5 ай бұрын

Probably a feeler gauge above or below that bearing you have to put in before you drop the pin all the way in.

@ashleygates1235 Жыл бұрын

I NOTICE YOU LOCK PIN SLID IN EASY . MY DOES NOT , DO I NEED TO HAMMER IT IN OR DO I HAVE THE WRONG PART

@1mattbutch Жыл бұрын

Hi Ashley- did you put the pin in the freezer and hone out the other parts so they are clean? You shouldn't have to hammer it in. If everything is clean it will be real tight but wiggle the parts to help.

@ianwinfield929 3 ай бұрын

I accidentally ate my kingpin smh because I forgot I put it in the freezer

@1mattbutch 3 ай бұрын

No shame buddy. I have made that mistake myself.

@ianwinfield929 3 ай бұрын

@@1mattbutch but seriously. Thanks for the step-by-step. This will help me when I get to replacing them. Right now I’m soaking everything in penetrant oil