echo pb-250ln carburetor adjustment hack trick

Рет қаралды 20,775

2 жыл бұрын

carb tools
amzn.to/3pQzsnH
check out my beautiful girlfriends etsy store www.etsy.com/shop/Sprunket.
company i buy most of my aftermarket parts from
hipastore.idevaffiliate.com/i...
if this video helped you donate a buck or two to my GoFundMe account
www.gofundme.com/f/help-me-bu...
The small engine guys are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com.

Пікірлер: 25

@joed1244 Жыл бұрын

Thank you ! Took me a whole three minutes to do. Worked great . Runs smooth and powerful again. I found an screwdriver from an eyeglass kit fit perfect

@PatrickBarton 2 жыл бұрын

Mine was doing that but I changed the fuel fuel filter and it worked great again. Appreciate your videos brother. You were a big big helping when I needed to adjust the carb on my ryobi 1838 chainsaw.

@smallengineguys 2 жыл бұрын

The fuel lines go bad alot.

@ShortbusRejects Жыл бұрын

This blower has two adjustments a high and low screw the other is a star drive down the center of the carburetor barrel

@kendalwilliam3980 3 ай бұрын

So there is actually 2 set screws one is located where shown in video, and there is one on top of the throttle barrel I believe it’s high side and the one under the gas bulb shown here is low side if I’m not mistaken..

@smallengineguys 3 ай бұрын

one in barrel is a pain in the ass so i dont bother with it ever

@charlesoverton Жыл бұрын

great lesson, thanks

@smallengineguys Жыл бұрын

You are welcome!

@charlesoverton Жыл бұрын

Nice trick, thanks.

@smallengineguys Жыл бұрын

No problem!

@shifttransformations6597 Ай бұрын

Awesome, video on my friend help me out so much. Couldn't figure it out, i just cleaned my carb out thought everything would be running well but it was struggling and bogging out. Did exactly what you said? It's running strong as an ox..

@smallengineguys Ай бұрын

Glad it helped

@Dawson6858 2 жыл бұрын

Torch next to gas, you're the man

@smallengineguys 2 жыл бұрын

As long as it's not lit.

@davidwismer2707 9 ай бұрын

It's a closed container, if your that paranoid go back to your bubble@@smallengineguys

@user-xe3gb7kk9v 4 ай бұрын

Thanks it help me A++

@smallengineguys 4 ай бұрын

Glad it helped!

@robertrobarge5294 Жыл бұрын

I've got the same blower but mine has a brass fitting in that hole I watched a video of a guy that took a drill bit and got his out with a drill bit so I tried that and I drilled down the brass fitting as far as I could go and it still won't come out to get to the screw to adjust the dang on thing

@smallengineguys Жыл бұрын

ummm never seen that. usually if you see brass ur looking at the screw. aftermarket carbs work well and no plug. i use hipa they are oem spec amzn.to/3CQOGQR

@brendangair2023 Жыл бұрын

@@smallengineguys some have a small brass sleeve that they pour the plastic into, it pulls out too with the plug, needle is below.

@smallengineguys Жыл бұрын

@@brendangair2023 ahhhh rhb70. Yeah so I heat up a tiny flathead screwdriver red hot. Press it firmly into the plastic plug hold it very still till cool. I use a bit of break cleaner to speed up the cooling process. After cool turn and pull a little at a time till it pops out. It's a flathead underneath.

@klink370 3 ай бұрын

Is the adjustment goal to set the screw so that it runs at highest RPM at WOT?

@smallengineguys 3 ай бұрын

Hit highest come back just a touch to the point it doesnt bog from idle to full speed.

@klink370 3 ай бұрын

@@smallengineguys Thanks. I didn't have a torch but I was able to heat up a jeweler's screwdriver with a candle and that worked for me although it took three or four attempts, each one moving the plastic out a tad until it finally come on out. Thank you so much for the video.