Ecovacs Omni X1/Turbo."Sink is Full" How to Fix This Error??

Рет қаралды 9,613

Жыл бұрын

Ecovacs Omni X1/Turbo."Sink is Full" How to Fix This Error?? Fix urself at home, just need some general service only.
Created by InShot:inshotapp.page.link/YTShare

Пікірлер: 54

@onibformi3590 4 күн бұрын

Thank you. I didn't expect the problem is solved so easily.🙏

@elladakene Ай бұрын

Very helpful, thank you

@alexcatalogna262 2 ай бұрын

thank you very much for this tutorial! It didn't solve my issue completely tho, there were debris in the channel that connects the LEFT hole (bigger hole) of the dirty water tank to the sink. You just want to apply pressure with a siringe or a long tube and using your lungs to let the debris pop out. Now it works like a charm!! Make sure you don't apply pressure to the little hole, right hole, because it seems to be directly connected to the pump. Hope this helps users and techincians too :)

@StelleRocks Ай бұрын

I was about to suggest the same thing with the syringe. Mine was exactly this issue. Debris from soap, scum and Cat food was also in there. But the suction helped too :)

@Weavel1983 Жыл бұрын

I had the same problem. I install a rubber oring seal at the base of the original seal for the dirty water tank. Since this improve, I never face the problem again. thanks for your videos for all the deebots. Evrytime is really useful 👍👍👍

@ecovacstechnicalsupport5278 Жыл бұрын

Welcome 🤗🤗

@blayzej Ай бұрын

Excellent explanation, thank you sir.

@LuDogMed 11 ай бұрын

This is the most recent issue you helped me resolve! I don't normally comment but this problem has been very frustrating until now, and I want to say.. Thank You!

@ecovacstechnicalsupport5278 11 ай бұрын

Thanks 😊

@Kurty2a 10 ай бұрын

Same here .. thanks a lot 😊

@vantouch 11 ай бұрын

Thank you so much.. This video is very useful.. 👍👍👍

@mwchan9066 5 ай бұрын

We followed your instructions. That’s work😃👍Thank you so much🙏

@ecovacstechnicalsupport5278 5 ай бұрын

Welcome 🙂🙂

@rohan..... Жыл бұрын

Thank you for this. I will follow this as I am also facing same error frequently since last 2month

@ecovacstechnicalsupport5278 Жыл бұрын

Plz follow this simple instructions.. hopefully will solve the issue ☺️

@rohan..... Жыл бұрын

@@ecovacstechnicalsupport5278 Thank you

@ecovacstechnicalsupport5278 11 ай бұрын

@@rohan..... welcome

@moafahmi Ай бұрын

very useful!!

@america6922 9 ай бұрын

Super easy. Thanks

@ecovacstechnicalsupport5278 9 ай бұрын

Welcome

@haiimfizi 7 ай бұрын

What should i do if water dont come out from both sides?

@mitultss9305 Жыл бұрын

Good

@ecovacstechnicalsupport5278 Жыл бұрын

Welcome

@drivescorvette Жыл бұрын

In the video you removed two rubber ports and explained to not push down to hard when reinstalling but what purpose does the right most port have? The left one is the path for dirty water to exit the sink so why and for what reason is there a port on the right side?

@laurencebarnes5361 3 ай бұрын

There's only one possible answer: it's an overflow protection. It'll likely redirect dirty water into the fresh water tank.

@TravisJReed 3 ай бұрын

@@laurencebarnes5361air suction.. it pulls the air out of the tank to create suction of the water from the sink into the tank

@AjitSingh-jq2bh 10 ай бұрын

Hi! Youre videos are really helpful. I have a problem where my X1 turbo is automatically activating sink cleaning over and over again and i have not pressed any buttons or done anything through the app. The deebot leaves the station and then water comes into the sink, it drains itself and then the deebot goes back in and then it does it until the clean tank is empty and the dirty tank is full. Do you know how to fix this? Any help would be appreciated 👍

@AjitSingh-jq2bh 10 ай бұрын

Weirdly, I put the child lock on and that temporarily solved the problem as I think that the station was automatically pressing the buttons, but now the child lock is deactivating by itself too!

@ecovacstechnicalsupport5278 9 ай бұрын

Ok plz power off the station, if plastic not yet removed from station touch screen button then plz remove it & use any alcohol tissue paper & wipe that touch screen panel & same tissue paper can use to wipe in the sink area left & right side sink sensors Mattel plates.normally it solves the issue but if still same then might be the touch screen panel or motherboard issue. there's a strip attached that touch screen panel to motherboard maybe damadge or loose. Can check that part as well

@bobbyboyderecords 5 ай бұрын

Can you run a cleaning solution through it? Like white vinegar? Would that help?

@ecovacstechnicalsupport5278 5 ай бұрын

Can not sorry

@payalanoop 6 ай бұрын

My ecovac x1 omni not dispensing water from clean tank. its brand new never used. Just bought yesterday. Can we fix it ourselves if you send us the part?? I also did all troubleshooting after talking to support.

@ecovacstechnicalsupport5278 6 ай бұрын

Station opening is quite complicated.. many wires & pipe at the back... Sometimes just in assemble they fix wrong pipe wrong side some time solenoid valve need to replace sometimes wster pump issues...take time to test

@nhareenpotluri4490 2 ай бұрын

This tip is worked fine for few days (10days) and again the problem is repeated can you provide the permanent solution.

@Cassp0nk 9 ай бұрын

I think mine has a blockage as gets good pressure in dirty water tank. Can you do a video on dismantling the base station? I got part way but can’t get back off…

@ecovacstechnicalsupport5278 9 ай бұрын

Actually Omni X1 or turbo station takes time to open & fix it back... video will be quite lengthy...once Free then only can do that..

@alexcatalogna262 2 ай бұрын

Hello, maybe you already solved the issue, if not read my comment above

@reenarodrigues2533 29 күн бұрын

Hi, my x1 omni. My clean water is leaking.

@cristiantapia22 10 ай бұрын

Can you please make a video of how to fix the X1 Omni station if clean water is not pumping? Mine is not pumping to the station or the robot. Please help!

@ecovacstechnicalsupport5278 10 ай бұрын

Need to Open the whole station then at the back got pump n solenoid Valve. Need to test which one is fUlty.. It take time.. Long process dear

@Calishere08 10 ай бұрын

⁠@@ecovacstechnicalsupport5278do you have photos of the pump and solenoid. I just want to confirm as I have a picture with part number

@anno2k29 10 ай бұрын

Please we are several people need this fix ... I started to disassemble bas station , but in 5h hour I haven't successfully found how find pump 🤯

@moiravanniekerk882 9 ай бұрын

Mine still not working. Cleaned it the rubber as well. What else dan I do

@ecovacstechnicalsupport5278 9 ай бұрын

Dirty water tank need to replace...if you feel that there's some suction noise but water not returning to tank means just dirty water tank need to replace

@moiravanniekerk882 9 ай бұрын

@@ecovacstechnicalsupport5278 thank you

@subliminalemcee 8 ай бұрын

Why not create the rubber gaskets so they don’t have that room at the bottom to slip down? This thing tells me the water tank is full every time it goes back to wash the pads. Its doing my tits in

@ecovacstechnicalsupport5278 8 ай бұрын

That's Ecovcs design sir..I can not do anything in this matter sorry

@TravisJReed 3 ай бұрын

@ecovacstechnicalsupport5278 I don't think that's true.. you can give the company the feedback many times the this is a major issue that's causing endless very expensive returns because of a extremely easy design fix not happening.. Sending a little rubber ring or gasket to go under that piece to keep it from sitting down completely or designing a new replacement rubber piece that's taller fixes the issue.. Show them the solution to the problem. Show them how big the problem is. Save them money on returns and repairs. You get promoted or a bonus etc. Everyone wins