Outstanding! The best, clearest, calmest, most informative car video I have ever seen. Thanks!

Thank you so much. This is my current situation with my Chevy Equinox 2016 that happened today. I panicked and rushed to a local repair shop for a diagnostic and got a quote for $800 to replace the ABS module 🥲🥲. My heart dropped from that shocker. So I resorted to Googling the issue and your KZfaq video popped up for the reset trick so I will definitely try that in the morning. If not, I will refer back to this specific video for additional help. Thank you tons. I will post an updated comment if all is successful either way.🙏🏾

Magnificent video and magnificent edition; Thank you for bringing to light an issue that for me was unknown, till today that the Light of the ABS was set on my car's dashboard. Blessings 🙏

ESPECIALLY APPRECIATE YOUR TEACHING SAFETY TIPS !! YOUR ONE OF THE FEW WHO TAKES SAFETY FIRST !! THANK YOU FOR THE TUTORIAL !! EASY CLEAR VIEW VIDEO AND LISTENING !!

Excellent, thorough and slow description. Thank you.

Thanks for the excellent video. And I appreciate it when you guys tell us girls who can help out with free services like OBD scanner checks. Very cool.

Loved the video. Just trying to find ways to check my abs on our Chevy Colorado 2012 ABS system before taking it to a mechanic. Thanks much --great advice on what to check on. Will try what I can.

Excellent video! Very thorough and informative. Your voice is very calm and easy to understand. Good job 👍

Thank you for this video. I have a unique problem that has stumped 3 mechanics and at least 2 really good computer coders.. My truck (2008 Chevy Express 1500 Cargo Van) had a problem that was traced to the throttle body harness. It was crimped. Replaced and 4 new tire sensors as well. Problem I experienced was check engine light and van putt'd & sputtered. Towed to mechanic and above fixes. Since then (3 months) intermittent ABS/Emergency brake light comes on and stays on for either a couple hours or all day. I have since noticed the check engine light periodically coming on at the same time. It eventually goes out, as do the other 2 lights. Today, I had to be towed. The van was showing signs of putt'n & sputtering while sitting idle. All the lights mentioned were on. My last stop I noticed the van felt as if it wanted to surge slightly while in gear and brakes applied. The speedometer was fluctuating up and down as well. Once under power the check engine light started flashing and I lost power. After shutting engine off and starting again...check engine light solid. Once under power for less than 1 minute...check engine light began flashing and loss of power. Mechanic is stumped. Any chance you've encountered this situation? Kim D.

Awesome video. Right to the point. Very helpful info

So useful n professionally the way you explain Really you deserve to be rewarded by utube

Absolutely PERFECT video and way to fix (or in my case) have knowledge of what is causing this issue on my old Dodge Truck.

Know nothing about cars, motorcycles me, using your vid managed to fix the abs light .excellent vid easy to follow even by me .

Really appreciate your knowledge 50yrs worth that is wisdom many thanks

Greaat Great video........... I love youtube - SO educational. This Video was concise clear sooo helpful. Thank you to all you guys/gals for educating the rest of us.

Thank You for the most common causes definitely will give it try ! 😎👍

This is very good tutorial on abs light on. My question is am rx 300,1999 model having same abs light on and speedometer not working what can I do pls but the transmission gear still working.

Didn't read all comments but FYI the larger fuses are also available at most auto parts stores and even Walmart.

One of most clear explanation and best camera work I’ve seen in a DIY video. Thanks

Very well done and explained. Thank you.

Great video. Very clear and concise. I have a 2009 F 250 and my ABS light comes on intermittently. There doesn’t seem to be any pattern to it. The brakes are working fine without the ABS. I bought a Blue driver scanner and I’m getting code C1096 Pump Motor Open Circuit. I’m going to dive in on this next week, but was wondering if because it is intermittent, do you have any insights?

Overall good video, only one point that I have issue with. The two block fuses are not dealer only and can be purchased at most parts stores and even most Wal-Marts in the automotive section.

Brilliant bit of information. I had a passenger front sensor come up so it was replaced and one 15 minutes later after leaving the garage the ABS came on again and now it says the driver side rear sensor needs replacing. Could that be possible ? Or could it be the fuse or abs module ? Thanks

First time watching. Can't believe I can actually SEE the stuff you are talking about. Awesome camera work and explanations. Thank you and subscribed.

Thank you, thank you and thank you for making the comments on having a secondary support for a jacked up vehicle. I see so many vids of people working under a vehicle with only one hydraulic support. Especially do not trust a hydraulic jack. My engineer dad and military training drilled this into me for years. It is a golden rule of working on heavy items. A set of jack stands is a cheap safegaurd and way cheaper than a hospital visit or a funeral.The video content on the troubleshooting was great.

You are indeed much appreciated I have learned something today much more deeply detail

Thank you! Hoping this is the solution for my 2004 Toyota Sienna XLE!

PERFECT video! My Mitsubishi outlander 2010 is recently showing ABS light issue. It is coming on and off on the dashboard. When it is on, then ACS off light turns on. The car is running well so far, no brake issue whatsoever with ABS light on. I have driven 5K+ miles with ABS light on. I got P1773 and C2116 codes. How serious is that?

Wow just have to say. Props for trying to help as many people as possible in the comments. Like wow you’re amazing dude. If you’re still answering questions, I have one. So my car has had the traction light on for a bit, but sometimes when I’m driving, abs and break lights turn on. Also, my car just started moving the speed diameter up and down in the middle of driving. The car feels perfectly fine, but, kinda scare about this symptoms. Already took it too a shop, but they couldn’t fix the problem and I have nooo idea what it might be. I am willing to pay for a abs module but idk if that’ll be the problem

Thanks for your videos very helpful information

Very clear and concise directions.

Mine came on in the rain.. thanks for the video 👍

Thank you very much, this video was very informative.

Good information! Glad I viewed your Vlog!

That's excellent. I ll try all of these and see if the ABS and break light go off on my Toyota Prius V 2013 . I changed my break pads and the light is still on . thank you. I subscribed

VERY CLEAR AND CLEVER THANKS 👍

Thanks bro. Very clear commentary.

Extremely wonderful camera work.

Great presentation. The control circuits on these ABS systems are typically low voltage, low amperage, which means you need to check the ABS Module grounds after you check the fuses, or check the separate voltage values either at the wheels yourself, or the voltages coming into the ABS module while a second person helps you by spinning each separate wheel one-at-a-time, but at a uniform rate. As I understand these systems, the interaction between magnetic part of the sensor assembly and the notches in the rotating wheel on the hub assembly generates the voltage measured as the wheel turns. Trucks are usually exposed to harsher conditions than cars, and exposure of the wheel sensors and connectors to water, sea water at the beach, salted roads, etc. over the years can result in degraded sensors at the wheels, or poor or corroded grounds or bad connections where the system wires connect to the push-on or screw-on connectors. Any of these issues can cause voltage variations that prevent the ABS system from knowing whether or not all 4 wheels are rotating at substantially the same speed, and if the signals aren't the same, the ABS light comes on. The profit margin between replacing the ABS Module and the sensors and sensor wiring on 4 wheels and bleeding or replacing the brake fluid is about $1,000 to 1,500 more than doing the checks he recommended, plus checking the grounds. The ABS module can be replaced with a new one, if necessary, without replacing the valves it is attached to, but it is likely it will have to be re-programmed for your specific vehicle. Programming Specs are often available online, but require special equipment. The alternative is sending a defective ABS module to a specialty shop which can repair the old one, and do any required programming. Costs vary, but usually much cheaper than having a new one programmed and installed - unless you have a shop that does this locally, it can take about ten days to send it and get it back, due to shipping times. P.S. The white illuminated board you have behind you in your videos is interesting, but it leaves your face in the shadows. Viewers like to see faces; something for you to consider.

Good Show, Sir :) 2003 Toyota Camry ACV 36. ABS light playing up. It's supposed to stay on with key on? & turn off, after start? This one lights up & goes off before start. If it stays on till start, then it stays on. Computer says no codes. Wtf?

Thanks for the info education on abs symptoms and possible causes creating abs light on dash. I'm trying to determine if the mechanic that told me my abs pump is failing is correct or not where as they said my coolant leak was coming from heater coil gear assembly but wasn't case and I paid $500 for that to be replaced and installed then that evening my abs light came on. I've bn spending money on repairing front suspension system. Have yet to replace engine mounts, brakes, and rear suspension as well as tires brakes and then eventually replace interior seating, steering wheel and center console gear shifter and compartment ..

Good vid, very step by step

Awesome information/tutorial, the only observation I want to make is that not all abs systems are the same there are different cars that have different abs systems.

Thank you. Great video. My old honda odyssey recently showed an ABS light on along with other lights. After stopping at traffic light, my car won't accelerate when pressing the gas pedal. Do you think that would be the only problem? What would be the expected cost to repair each individual issue vs changing the whole ABS unit together? Here in CA prices can vary so much, price gouging is so common. I recently brought a 2013 escalade to the shop and they told me my rotor and axel in the back wheels have to be replaced, and I paid $6.5K for it. I am scared to bring my car to any mechanic worrying they are going to ask me to pay $2K for this issue.

Top vid .very informative ..thanks

Very good video thanks 👍

Thanks a lot... Very informative.

Excellent video.

Clear explanations beast video thanks

Thank you sir very good explain

Thank u for your app n information u got 100%.well done

Hi thanks for the good review I have the same problems plus hand brake light and the motor for abs on even after turn of the engine .i have to unplug abs to shut it off.?what can you say about that.thanks

Hey Michael I have a question you might be able to help me with... I have a 97 Dakota my brake pedal gets stiff and hard to press when I am coming to a stop but it doesn't happen every time and my abs light isn't on... do you have any idea what's the problem? Please

I liked this video so much after watching and though asked my question that I just decided to Subscribe 😍

Recently bought a 2010 charger sxt an when I make a sharp or full left turn esp/bad light pops on every time about after being started. I've researched it some an found quite a few articles of the same problem either the dodge brand. Noticed also my driver's side front rotor has some signs of pads being worn down to low an pitted it. Also wondering if having a different size tire on the driver's side rear would throw the lights. an toms sensor comes on

Just stumbled upon your video, good stuff. Recently got a DTC 66-1 (Brake Pressure Sensor Failure) and 98-1 (ECU Unmatched) for my 2000 Acura RL. Got any tips on how to fix this kind of stuff?

Hi! Thank you for taking the time to share your knowledge of vehicle repair with the world. My ABS light has been on (steady) since I had my tires replaced 3wks ago, getting ready for winter. For two days, the the ABS activates, showing a car skidding icon (on completely dry asphalt here) and the gas pedal loses pressure. It activates every time I have to start it up (minimum of 6x daily) and today it happened while I was facing oncoming traffic. Can you please tell me which of the 4 reasons explains the issue my 07' Lincoln Navigator L is having? Thanks a bunch!

I have all three lights on: ABS / BRAKE / ESC , mine is a 07 hyundai santa Fe , but the main concern is as soon as I connect the battery terminal I can hear an Strong noise coming from my ABS module/pump, is like the ABS is active/vibrating, is there a chance for one of the sensors are activating the module in that way, even without the ignition key inserted??? have you an idea about what is going on, or test I can do? thanks in advance!!!

How do you determine if the abs control is fsulty

Most fuse / relay blocks have a fuse pulling / insertion tool tucked away somewhere. Hard tools can easily break the fuse. But a great, easy video to follow. Thanks

I replacing my ABS control module due to a nasty leak. It's on a 2006 lexus IS350. Once replaced does it require a reprogramming process or is it just simple plug and play?

Great video, I have a Ford explorer sport Trac 2008 and I recently replaced my tires of the vehicle and it recently started to turn on my abs light once I speed up to 15 mph, breaks work perfectly fine with no issue so I'm stumped as to why, I'm unsure if wheel unalignment may also have something to do with it.

Can you tell if the magnetic ring should have magnets all around the ring? Because I replace the ABS sensor and watch that ring but it only had a few magnets... very good video by the way!

I have a 2001 Toyota Camry, and my abs light goes off whenever I hit bumps on the road and my car brakes stutters. My car has already turned off completely due to this problem. Is something loose in my car

im having a no start traction control + stability control light on.. would a sensor or an ABS module would cause a no start?

Hi i.just ha d my honda fit replacement of rear wheel bearing and front axle assembly, we provided both parts,now when we pick up the car the eps and abs lights was on, another mechanic manuever the steering and looks like eps was off now but ABS lights still remains on

Hello, I have a 2005 Chevy Colorado, and I have a ABS fault, traction control fault, stability control fault, all going off and has shut down my traction control and ABS. I have checked the rings, replaced the sensors, cleaned all connectors, and checked fuses. I got the truck from my brother who has had problems with the abs and traction control ever since he bought the truck. He actually had wheels lock up on him driving down the highway, after replacing the sensors it was running fine, then when we were driving we noticed one wheel started dragging and the front right wheel started grabbing spirraticaly. We cleaned the rings and sensors and it stopped but then suddenly threw 3 faults and we can't figure out why, please help have no idea where to turn.

How much would that cost with a mechanic just curious. Cause he had mentioned my rotors where looking very rough. Could this most likely be the cause? Thanks imma try the fuse before I remove all 4 tires.

Thank you for the clear video, precise explanation & minimal theatrics 👌. I am based in South Africa and attempting to resolve a 2 year long problem. Vehicle is a 2005 Renault Megane 225 bhp Sport. ABS light came on , with concomitant loss of traction control, speedometer, cruise control.At the time , OBD revealed only right front abs still active. New Rotors with pressed wheel bearings having abs magnetic strip AND new ABS sensors have been fitted. OBD scans all show front right abs still active, the other 3 not. Can a 4-channel abs module fail on 3 channels ? What other possible causes should I be looking for ?

Awesome video/ information.

My lexus abs lights came on after going through a foot of snow going to work, could that be months ago why my lights never turned off?

Can't find the abs fuse box light to see if I need a new one. The light won't go off.

2009 Dodge caliber 2.0 ABS light came on. Lifted front end up and ran it to 50 mph and listened for bad bearing. Sounded fine both sides. Checked each back tire and turned by hand and all seemed fine for noise. Grabbed each tire and wiggled and evrything seems tight. Asked my son about the tire pressure and found that all the tires were at 25 to 27 psi. Filled all tires to 33 psi and we took it for a run. Guess what the abs light went out. Completely surprised me. Check your air pressure of the tires first. It was a very simple fix............................................

The ABS LIGHT ON MY nissan Versa 2013 is on right now ( when in motion )....what is your take on the 2013 Versa

I have a 2000 Chevrolet Silverado 1500 5.3, and my ABS lite come on frequently but never on constant and I've replaced the module also but that was a waste of time and money. When I finally went to another mechanic, he showed me that it's not showing any codes on his scanner. Any ideas on how to tackle this problem?

I have Toyota Hilux 2009 and the abs fale work when i press the pedal on slow moving but the light doesn't come on . What is the cause

Very good explaining video thanks

Thanks for the great video. I have the same problem with Cadillac Escalade ESV 2016.in raining, few lights get ON, traction, ABS,and the steering gets harder even undeliverable. Do you think these are the same issue and can be fixed by changing sensors?

Thank you sir,

Don’t forget about BUS problems! All sensors, fuses and modules can be good but a bus / electrical issue is always possible. Can test that issue through testing for power through you’re harness or splice packs!

Do you think covering the connector in the wheel well with grease would do any good to help protect it from moisture. Seems like a bad place for them to put it

hey this was a very simple and informative video. I also have a question, recently the abs and brake lights lit up on the dashboard and I did a computer check but I couldn't seem connect to the control module. Is it possible that the module itself is damaged or is it some wiring issue or any other. Love to hear your thoughts on this.

Hi can you please guide me, I have 2008 Jeep Patriot. Since last 1.5 months, my abs, traction control light and esp lights coming on often. Until now maybe 8-10 times it happened like that in last 45 days. Usually, the lights comes on within 2 to 5 mins of vehicle starts moving. Then, when the vehicle is off for a brief period of time, say 2 hours plus and again when you start the car the lights will be on. But once the car starts moving it goes off. Can you please help me what might be the issue in here and what I need to be looking at please.. During abs lights on moments, braking seems to function more or less normal, but I find the engine rpm increases abit more than usual for the speeds. Other than this I don’t see any other difference in driving with the abs , traction control and esp lights on. any help is highly appreciated. So that I can resolve this issue.

Great video

Hey if my truck adv trac as well as hill descent hill assist not available warning lights comes on once in awhile. What would cause this issues

Thank you

Thanks for the video

Hi really good explanations here, With my citroen c3 the abs light had come on and off now and again and recently told me to stop, with the handbrake light. Then the power steering would go with the steering wheel light, the air bag light and the speedometer would stop working. Car would run the same but be jumping alot. I had the front passenger and rear driver side sensors changed after the codes showed up on the computer test but it seemed to be the same if not worse. I'm just wondering if this sounds like a worse problem due to all the lights, steering and speedometer problems. Thanks

Great Job!

ABS light on my 1987 Vette is now on after the mechanic installed new front brakes due to it jerking to the left when braking. This did not correct the problem. He said the ABS system was bad. I found a used one on eBay. This still didn’t solve the problem. The light is still on.and the ABS is not working. Any input from you is appreciated.

I need to completely clean out my brake lines from contaminated fluid. I want to blow break cleaner through the lines but will it mess up my abs? What to do? On a 2004 civic, discovered daughter put power steering fluid in the master cylinder.

Well done!

I THINK THEY GAVE US ALL THESE SENSORS TO DRIVE YOU CRAZY SOME TIMES. BUT STAY SAFE EVERYONE WITH YOUR PROJECT . JUST GOT ME A 96 SONOMA HIGHRIDER 4X4 AND I HAVE THIS PROBLEM.

for over 50 years cars operated without abs . we don't need it Ralph Nader.

very good video keep up the good work

Thank you so much ,,, !

The electrical connection points can be sprayed with WD-40 , WD stands for water dispersant .

I just had to replace both wheel hubs and the rotors, pads, and calipers on my 08 Colorado and the ABS and Fault light are still on. How do I get them to go out or do they go out on their own after driving it?

do you teach at a 10th grade or lower level? just wondering cuz you have a very calming voice and tone that might've helped me learn math early on and you take your time with the explanation and not stress me out like some other teachers used to do when i was in grade school

I have my ABS and traction control light on but it gives me code B162E-15 wich is a light bulbs is out so I replaced the light bulb but when the bulb goes on the light in my dash turn off but when the bulb is off the lights come on in my dash (2015 challenger R/T plus) thank you hope you can help me out