EEMANN TECH ULTIMATE TRIGGER FOR CZ (44-130084). New tools by Eemann Tech.

Рет қаралды 24,770

3 жыл бұрын

1. Eemann Tech Ultimate DA/SA Trigger for CZ
The shape of the ultimate trigger was developed with help of biomechanical engineers and physician for the best possible ergonomics, performance and perfect functioning of your trigger with the CZ platform.
The radius of the curve in the trigger is half way between the factory trigger and our flat trigger giving the best of both.
There are two adjustable screws the trigger that allow for custom adjustment in both directions, both pre and after travel.
The ability to remove unnecessary pre travel allows the trigger in double action mode to have a shorter reach which helps with smaller hands.
The over travel screw allows for a shorter press and reset.
The end of the trigger has a tighter radius than the factory model and won't bottom out against the frame of the pistol, it also allows for smaller hands to feel more comfortable.
The DA/SA Ultimate Trigger allows for more precise control of the trigger press and reset!
Specially produced for use in Double Action mode with your CZ pistol
Works perfectly with all steel framed CZ pistols with any installed disconnectors.
Compatible with:
• CZ 75
• CZ 75 SP-01
• CZ 75 SP-01 Shadow
• CZ 75 SP-01 Phantom
• CZ 75 SP-01 Shadow Line
• CZ 75 SP-01 Shadow Orange
• CZ 75 SP-01 Tactical
• CZ 75 B&BD
• CZ Shadow 2
• CZ Shadow 2 Orange
The set includes:
• Ultimate Trigger for CZ Shadow
• Screw for Eemann Tech triggers (after travel) for CZ (44-131002)
• Screw for (pre travel) adjustment - 4mm length (44-131004)
• Screw for (pre travel) adjust - 3mm length (44-131003)
• Competition Trigger Pin (44-130064)
• Competition Trigger Spring (44-131109)
• 1.5 mm L-Shape Hex Key (44-030012)
You have all you need for the perfect trigger group in one package
Installation takes only a few minutes.
Available colors:
• Black
• Silver
• Gold
Made from:
• Aluminium (Black, Silver)
• Brass (Gold)
Legal in IPSC and USPSA Production
2. Eemann Tech sear spring installation tool for CZ 75 pistols and their clones.
3. Eemann Tech trigger spring tool for CZ 75 pistols and their clones.

Пікірлер: 62

@CZFanGrrl 3 жыл бұрын

I bought two flat triggers and I loved them, then I bought the Ultimate and out came the flat triggers. The Ultimate is amazing and everyone that shoots my Shadow with the Ultimate is getting one for their gun.

@mps9649 3 жыл бұрын

@CZ FanGrrl..Is the difference between the flat and ultimate significant in DA? I don't have any reach issues with the stock trigger in DA and was interested in the flat for the crisp SA....but now came across the Ultimate.

@davidmacnab5213 5 ай бұрын

FYI - it was not that easy for me to remove the trigger bar pin; the holes did not line up as neatly as in your video. I ended up having to remove the sear cage to get enough movement in the trigger bar. After that all went well. As you say, tolerances differ. I also did not have to use the pre-travel screw; the trigger is at the end of its travel for double-action. Terrific trigger for my hand. Very comfortable and well worth fitting. Thanks.

@Steel_shooter Жыл бұрын

Got and installed mine in the S2 today, love the feeling.

@rogerzobrist4211 3 жыл бұрын

Work perfect 👍

@paulhagiantoniou530 3 жыл бұрын

Awesome 👏

@crookedikon 2 жыл бұрын

I see my next upgrade in the making. Plus I need the trigger to match the grips anyway.

@wvultra 3 жыл бұрын

Hi Paul! Wondering if the Gold (brass) Ultimate Trigger will "tarnish" with use, over time, from the natural salts emitted from our skin? If so, would it be easy to restore the factory finish? Thanks!

@Speed-shooter 3 жыл бұрын

I’m a firm supporter of the Eemann stuff. Springs to triggers for my shadow 1 and 2. I’ve now made the leap to the cz czechmate. My question is please tell me your springs and floating pin and other eemann accessories work on the czeckmate. Thank you for all the videos as they are extremely helpful Sir.

@paulhagiantoniou530 3 жыл бұрын

Hello Bernard Firstly Thank you for your support of the Eemann Tech Brand. We have a range of products suitable for the Czechmate, the main springs and recoil springs are the same, the trigger return spring is different and we have a competition version available. Triggers are available too in a variety of models, be sure to choose the ones for single action only. Glad you’re enjoying the videos 😊

@paulhagiantoniou530 3 жыл бұрын

Yes the competition trigger pin works in the TS model

@Speed-shooter 3 жыл бұрын

@@paulhagiantoniou530 thank you very much and keep up the great work.🏆🏆🏆

@paulhagiantoniou530 3 жыл бұрын

@@Speed-shooter Cheers Bro 👍

@jesenikm 6 ай бұрын

I have ordered the ultimate trigger today. It was not mentioned if it fitts the CZ P01/ compact... Hope it does

@Blebobeep7492 16 күн бұрын

Did it fit your p 01

@iZephiroth Жыл бұрын

Is the trigger compatible with the CGW reach reduction kit? Thanks in advance.

@TheHoyeah69 3 жыл бұрын

How do you stop the grub screws from moving? I've found that the over/pre travel screws always move even you put locktite on it. And it always come out at the worst possible time, ie, when you are in a match competing.

@paulhagiantoniou530 3 жыл бұрын

Hello Jim Always use loctight blue on these types of screws, you can use red but will need heat to loosen, I apply blue and it works well. Further I always check the pre and overtravel on my triggers at my regular service intervals

@CZIndonesia 3 жыл бұрын

I always recheck before big match for the screwa

@StrangersIteDomum 5 ай бұрын

Looks just like Cajuns "flat" trigger

@zoomzoom3345 3 жыл бұрын

Do you as EEAMANN Tech produce short reach trigger system similar to RRK of CajunGunWorks?

@paulhagiantoniou530 3 жыл бұрын

Not at the moment Zoom, however the pre travel screw on our Ultimate trigger can eliminate allot of the pre travel which in turn positions the trigger further back in the frame

@zoomzoom3345 3 жыл бұрын

@@paulhagiantoniou530 Thank You

@davidgibbs1083 Жыл бұрын

So this trigger by itself is a reach reduction kit and will allow you to adjust your reset

@PeacemakerPL 2 жыл бұрын

Any chance for flat trigger for P07 / P09 with decocker?

@deckeogh 3 жыл бұрын

Hi Folks, is adding this trigger to an IPSC Production Gun permitted: 18.4 Aftermarket springs and trigger assemblies are permitted.? Does a full replacement trigger qualify? Thanks

@polluxxullop5304 3 жыл бұрын

Section 18.4, Appendix D4: IPSC Rulebook, Production Division „Aftermarket springs and trigger assemblies are permitted.“ www.ipsc.org/pdf/RulesHandgun.pdf

@deckeogh 3 жыл бұрын

@@polluxxullop5304 Thank you

@paulhagiantoniou530 3 жыл бұрын

Hello Sir Trigger assembly is the term used in the production ipsc rules, our kit is an assembly as it contains a number of parts

@BitcoinNBullets 3 жыл бұрын

I had to remove the too screw completely to get the double action trigger pull to work correctly. I tried it in completely through to all the way out of the gun and all the way out is the only way DA works. Any tips? My pull measures at 6 lbs DA and right at 2 lbs SA. Does this sound about right? Thanks in advance.

@paulhagiantoniou530 3 жыл бұрын

Sounds good Jason, the trigger will get better with time too. The pre travel screw is sometimes not required depending on the individual guns tolerances, some benefit from having the pre travel screw as it helps to remove any, if yours has none it’s a good thing. Setting up the over travel screw is a little tricky to actually catch the over travel. I will do a short video to demonstrate how I catch it

@BitcoinNBullets 3 жыл бұрын

@@paulhagiantoniou530 thank you for the reply

@johnkendall6114 Жыл бұрын

That's the answer I needed, thanks Paul!

@as685030 2 жыл бұрын

Do any of these triggers work for the CZ 75 D (PCR)? Any adjustable rear sights for the PCR?

@as685030 2 жыл бұрын

@Jan Holcomb I bought one and it did NOT work with my PCR or my 97

@thegunshowguy Жыл бұрын

Will this fit in my 75p01?

@zarinkai2927 3 жыл бұрын

Would love to buy the thumb rest slide stops. But not available in US . 😢

@paulhagiantoniou530 3 жыл бұрын

Hello King, try Dot40 and Hardball ballistics, both in the US and distributors of Eemann Tech

@as685030 2 жыл бұрын

Check with Hardball Ballistics to make sure you get the one that will work with your gun.

@Maddaxes Жыл бұрын

I like the eemann tech products but I wouldn't get the thumb rests. I shot it during a match and my slide kept on locking back

@rafaelfranco9659 2 ай бұрын

Does this trigger worth for shadow 2 compact???

@HighCappa45 7 ай бұрын

Does anyone know if this trigger work for the CZ 75 P01 cause it says it works for the 75 so I’m guess that’s all the variants???

@jett9943 3 жыл бұрын

Hi all, is the pin holding the trigger with the trigger bar a solid pin? Or is it similar to the factory trigger pin that is staked?

@dmitrieemann 3 жыл бұрын

its a solid like a factory

@jett9943 3 жыл бұрын

@@dmitrieemann thank you for the information. Much appreciated 👍

@sandlotpass 3 жыл бұрын

Will the ultimate trigger fit on the alloy framed CZ 75 P-01?

@dmitrieemann 3 жыл бұрын

Yes, will fit

@chefistopatrick385 2 жыл бұрын

@eemann Tech - is this ultimate trigger 130084 is the upgraded version of the eemann tech sa/da flat trigger?

@dmitrieemann 2 жыл бұрын

Hi, no, its a different model.

@chefistopatrick385 2 жыл бұрын

@@dmitrieemann what trigger do you prefer between the ultimate and the flat?

@chefistopatrick385 2 жыл бұрын

@@dmitrieemann i also upgraded my cz shadow with ET-130052

@dmitrieemann 2 жыл бұрын

@@chefistopatrick385 Ultimate is not so specific, like Flat. Who really need FLAT trigger, choosing flat, but if you just dont like CURVED original trigger, your choice must be ULTIMATE model

@rafaelfranco9659 Жыл бұрын

IM from Chile, how can i get one??

@Aureliopuglisi 2 жыл бұрын

Hi, I bought the latest model of the Trigger, EEMANN TECH ULTIMATE TRIGGER the slightly curved one, for CZ Shadow 2, but I noticed that neither the 3 mm nor the 4 mm dowel can be used, as putting the 3 mm dowel (the shorter one) if you tighten it to adjust the pre-stroke, the trigger is blocked. I would like to understand how to do it. Thank you in advance. Ulteriori informazioni su questo testo di originePer avere ulteriori informazioni sulla traduzione è necessario il testo di origine Invia commenti Riquadri laterali

@dmitrieemann 2 жыл бұрын

If its blocked, you need to remove it. Recommended to use with frames with big tolerance. Just remove this screw.