Ekopel 2K Live | How To Refinish A Bathtub | The Whole Process in Easy Steps

Рет қаралды 50,757

5 жыл бұрын

Ekopel 2K Live | How To Refinish A Bathtub | The Whole Process in Easy Steps
Live Uncut Start To Finish Ekopel 2K Install!
Order yours today at refinishedbathproducts.com
Also Available on Amazon!
This is a how-to demo on Ekopel 2K. Beware attempting this process with lower quality products will not come out the same.
Trust the original, Ekopel 2K!
Refinish With Confidence.
Thanks for watching How To Refinish A Bathtub with Ekopel 2K Live! Unedited To Show The Whole Process.
For further information or to order yours call: 877-882-2278
Or visit our website:refinishedbathsolutions.com
The best refinishing kit Available Now: www.amazon.com/Ekopel-Bathtub...
Every step of the process to refinish your tub with Ekopel 2K is shown and explained.
REMODEL IT YOURSELF: No need to hire a spendy expert. This refinishing kit takes the expense out of bathtub improvement. Perfect for renters, apartment dwellers, and residential or commercial tubs, sinks, and showers.
ECO-FRIENDLY & NON-TOXIC: Fumes-free and made without harmful chemicals, Ekopel’s long-lasting, oil-free glaze never peels! Its thick, full-seal coating restores tub surfaces to a “like new” bright gloss.
STEP-BY-STEP DEMO VIDEOS: Free videos take the mystery out of re-glazing. We guide you through the prep, application, and finishing steps. If you can follow instructions, you can DIY recast your tub in 2 to 4 hours.
KIT CONTAINS EVERY TOOL YOU NEED: Our tub & sink remodeling kits include foam roller with covers, scooper boxes, and easy-pouring, safe-to-use Ekopel 2K enamel.
24-HOUR CURE TIME: After applying Ekopel, it takes 24 hours to “set” before using your tub/shower. Maintain 72 degrees Fahrenheit in the bathroom for the shortest cure. In lower temps, it will take longer to set.
Order yours today at bathepoxy.com Use coupon code youtube10 for $10 off at checkout.
EKopel 2k is the premier bathtub refinishing kit. We provide top-notch customer service and the longest-lasting bathtub kit on the market.
#ekopel #homeimprovement #bathtubrefinishing #bathtub #ekopel2k

Пікірлер: 107

@simmerslodraw Жыл бұрын

This stuff works so well. I did it in terrible circumstances, no control over dust, bathroom in use by kids etc etc, and it dried rock-hard and smooth aside from some very minor imperfections. No big deal.

@simmerslodraw Жыл бұрын

Big take away for next time was just to buy extra

@simmerslodraw Жыл бұрын

Also low to no odor and easy cleanup before curing.

@kristynelson7318 2 жыл бұрын

Thank you so much for this video. We were SO nervous to do our claw tub but it has been needing it done since we moved in. This was so helpful. My husband & I did ours last night & it looks amazing. It looks like a brand new tub. The product, ekopel, was easy & great. If we knew how easy it was-we would of did this a long time ago. Thanks again.👍🏼

@Orangedome 5 жыл бұрын

Thanks I recommended this to my client. Instead of the cheap Homex they wanted me to use. Quality is a must. I'll let you know how it went.

@Susan70003 4 жыл бұрын

How did it go? Did you make a video?

@ethantimm2780 2 жыл бұрын

Great video, it's actually great that it is unedited... You can set it up running while you work!

@gregoryworth6644 4 жыл бұрын

Thanks for your videos and explanations, followed all your details on our claw foot tub, it came out great and as I took pictures and sent them out I said it looks great and is better than the picture, some spots may look thin, they are not, it’s shadows,

@robertmckissick9347 4 жыл бұрын

Hi...just left a comment on another of your video's on this tub treatment...clawfoot tub that I am refinishing. I am surprised the home owner didn't want the faucet and drain removed for this. I like the idea of the propane instead of the heat gun...seems you wouldn't get a much air blowing around with the torch and less chance of dust, etc. Nice video....definitely going this route when it starts to cool down in about 3 or 4 months (Florida...) Thanks again...

@TruckerDawntheBreeze 4 жыл бұрын

Hi. going to do my friends tub.. saw the question about pinhole a couple days later. Was that caused by bubble not popped? Thank you

@uqox 5 жыл бұрын

This is very, very helpful. Would you consider showing the "repair" of a previous coat done with cheaper materials? I live in an apartment and, based on your videos and other videos, the building renovated and used a cheaper product that bubbled and pealed by the 4th month of me living there. I would like to repair it myself and just need some clarity on what to do about the pealing and bubbling current coating. BTW I'm ecstatic that you have a "pro kit"!!! I will circle back and add an update once I tackle this myself. In the meantime, I'll keep watching your demos. Many, many thanks for your professional demos.

@jrocket7368 3 жыл бұрын

I have 0 experience with this kind of work. but really seems simple enough. its nice having a walk through with lil tips

@JohnDoe-dk8zz 2 жыл бұрын

Thanks, i was able to do mine just fine. For a first timer the result is nice. A little bit of orange peel on a specific place but overall im happy.

@RefinishedBathSolutions 2 жыл бұрын

To fix any orange peel areas can sand smooth with 220-320 grit sandpaper then if you don't need more material go to 600 then 1500 then use any car buffing compound to bring the shine back. If after sanding you do need more material use our pour on touch up kit to fix.

@sarahweaber3275 4 жыл бұрын

When do you remove the tape from the drain?

@victoriansunset 3 жыл бұрын

Can we get an update on this tub, please? I am doing mine this weekend and would really like to know how it has held up.

@aprilstephens142 4 жыл бұрын

Just to be clear, with this process I do not need to sand the tub?

@charliehalo100 4 жыл бұрын

Have a tub that was sand blasted. it is all pitted now. Did the refinish and it is shinny and white but still pitted. How can I get rid if this and make it smooth again?

@timwallace6246 4 жыл бұрын

BTW, your work looks fantastic.

@veedadixon3749 4 жыл бұрын

This is the second video I've watched with you and I have a couple of questions: 1. Can you mix the part B in with a mixer paddle at low speed and 2. I want to tint this with a alkaloid base tint to a black color, will this break the product down?

@RefinishedBathSolutions 4 жыл бұрын

No! Be sure to watch the mixing video to prevent air bubbles, and product failure down the line. Hand mixing is required. Black isn’t an option. Alkyd tints will darken or change the color but the base is white and needs to be a somewhat light color.

@aloissuter1071 4 жыл бұрын

Great job. Second video I watched you do great work. My question is I have some pretty good spider web cracks in my bottom and some chips. Do I use a filler product before coating?

@francisphillips4497 3 жыл бұрын

Hi , I have the same tub and wanted to know if she or you did the feet on the tube if so what did you use and how to do it. Also the out side of my tub need refinishing also is that more difficult to do.

@RefinishedBathSolutions 3 жыл бұрын

Yes you can recast the feet as well with the ekopel. You can dip the feet into it. For the outside you will have to flip it over and then pour like you would the inside

@misslisa5236 3 жыл бұрын

I'm a nervous wreck, but I think I'm going to buy your product and try to refinish the old clawfoot tub I just bought.

@RefinishedBathSolutions 3 жыл бұрын

No need to worry!! watch all our videos and follow the directions given and you will change the tubs life!! We are here to help if you have any questions feel free to chat with us online or call and we can help!!

@forwardmomentum7845 4 жыл бұрын

I used a kit from rustoleum which adheres okay and doesn't chip, but absorbs stains like crazy. Might I ask how this one holds up in terms of maintaining its colour and resistance to staining/ It would be worth the extra money if it holds its colour (and doesn't chip).

@RefinishedBathSolutions 4 жыл бұрын

With proper prep work our product won't chip or peel for up to 20 years. The only problems we have run into with staining is if it didn't cure for long enough and people leave there soap or shampoo residue in the shower it can cause staining. So we recommend to rinse the shower out after you use it to make sure there is not residue left for 30 days after you apply Ekopel. After the 30 days is up you should be fine.

@albermansour4728 3 жыл бұрын

Good informative video. One question, if there are chipped areas in the tub do they need to be fixed before applying the Ekopel 2K?

@RefinishedBathSolutions 3 жыл бұрын

Yes if there are chips or cracks they would need to be filled in and fixed with car bondo before you apply ekopel 2K.

@sharonromine1982 2 жыл бұрын

I have small shallow pits in the bottom of mine. I had envisioned the product filling these holes. Am I wrong on this?

@keisharoland9532 3 жыл бұрын

Good Day. I did my tub last night and we got nervous and repoured some on the ledge. Now it dried and have drip marks on the inside. How do we fix it without using a touch up kits.

@RefinishedBathSolutions 3 жыл бұрын

You can sand that smooth with 220-320 grit sandpaper. Then when it is smooth to the touch you can double the grit of sandpaper to 600 then 1500. Next you can use any car buffing compound and it will bring the shine back.

@huyquoctran2088 4 жыл бұрын

What cleaners can you use for reglaze tubs. People told me no harsh or abrasive cleaners but i dont know which is which

@emilysmall7775 4 жыл бұрын

What is the black scrubby that he uses in the beginning to clean? Is it steel wool?

@RefinishedBathSolutions 4 жыл бұрын

Emily Small we just use a dollar store scrub brush.

@austinchase5882 5 жыл бұрын

You didn't use the comb on this clawfoot tub, but you did in a different video on a normal tub. Is that because you used the roller on this tub and/or its a clawfoot?

@RefinishedBathSolutions 5 жыл бұрын

Austin Chase yes, the comb method is how we did installs originally. It is slightly more cost effective to do it that way. Our preferred install method is with the foam roller.

@LYR74 3 жыл бұрын

How long does it take to dry once applied? I will be having it installed in its final destination in the next 24-28 hours... I currently have it in the apartment kitchen

@RefinishedBathSolutions 3 жыл бұрын

It takes24-36 hours to dry

@heathertheheathen6145 4 жыл бұрын

I used this product today and let me say ,it's not ideal for short people with short arms.. I was kept bumping into the wet areas and couldn't get all the excess eloped and it looks like it pooled up where wall of tub and bottom of tub meet.. SO JORROR OF HORRORS WHAT DO YOU DO TO HELP THAT SITUATION..WHEN I WENT BACK IT COULD NOT SCOOP NO MORE EXCESS IT WOULD HAVE JACKED WHOLE THING UP..HELP ME EKOPEL KANOBI ,YOUR MY ONLY HOPE!!

@Xibalba501 5 жыл бұрын

Hi! I recently did this to my clawfoot tub. Everything turned out great until a day or two later I noticed a small pinhole on the bottom...do you have any recommendations on fixing this?

@RefinishedBathSolutions 5 жыл бұрын

Greg Branson we have a small touch up/repair kit on our website. Refinishedbathproducts.com

@RefinishedBathSolutions 5 жыл бұрын

Greg Branson give our office a call tomorrow at 877-TUB CAST I’ll see if I can help explain another easy touch up option.

@Xibalba501 5 жыл бұрын

Refinished Bath Solutions will do! Thanks!

@kelliwinters225 Жыл бұрын

If my tub is removed and I have no drain in, do I just let the ekopel run right out the drain hole or should I still tape it

@RefinishedBathSolutions Жыл бұрын

If its a clawfoot unit and its completely uninstalled then yes you could just place something under the hole to catch any excess. If the unit is installed then you would still need to tape up or the pipes could get wrecked.

@francisphillips4497 3 жыл бұрын

The film has stop with you scrapping the tub , but you are talking doing other step snd it's showing you bending just still guess the tape stopped

@LFL-qp1fg 4 жыл бұрын

Would it be good to have the paint dept shake the can prior to use?

@RefinishedBathSolutions 4 жыл бұрын

Thomas Randall no, stirring by hand is the only recommendation

@LFL-qp1fg 4 жыл бұрын

@@RefinishedBathSolutions Ok, thanks. I was not sure if it was like regular paint.

@rachelhirsch8631 5 жыл бұрын

Great vid, thanks. Question: do you now usually use a roller with everything or is it because it's a rounder tub? If you use a roller all the time now what size and thickness roller do you use?

@RefinishedBathSolutions 5 жыл бұрын

Great question. The mini 3-4” foam rollers are the best. We are looking for a cost efficient way to include then in each kit. For spreading out the bottom and leveling out the excessive find the roller to be the fastest and easiest way to do it. I am going to do another live video on a regular tub on Friday and will be using the roller to level the top and bottom edges, also to get a quick coat on the front. I will try to be as descriptive as possible to help make the new process even easier.

@rachelhirsch8631 5 жыл бұрын

Brilliant, thanks! What time? Working on a 60" x 30" tub, need to do the front as well as the small sink. Your videos have helped loads with the prep.

@RefinishedBathSolutions 5 жыл бұрын

Will be going live in about a half hour or so.

@klausmouse 5 жыл бұрын

Can this product be sprayed on using a airless spray gun?

@RefinishedBathSolutions 5 жыл бұрын

b k no. You can use our other material, tub Cast 5000 that is available as a spray on coating. Best off using an hvlp sprayer though.

@jonathans5318 2 жыл бұрын

How do you fix fisheyes in the surface? I must've got some contamination on the surface???

@RefinishedBathSolutions 2 жыл бұрын

If they are hardened I would recommend sanding smooth can even fill with car bondo then sand smooth if needed then use our pour on touch up kit to fix.

@Z33Garage 3 жыл бұрын

Is this mixable with a drill mixer?

@RefinishedBathSolutions 3 жыл бұрын

Ekopel 2K can not be mixed with drill mixer, it will cause bubbling and fisheyes. You can use the drill mixer for our counter cast products though.

@michaelwilcher5228 2 жыл бұрын

Hi there, I have an old tub needing to repair. It has been coated before and some of the prior repair is chipping off, how do I remove this old epoxy?

@RefinishedBathSolutions 2 жыл бұрын

If your using ekopel I would recommend sanding it smooth to the touch with 220-320 grit sandpaper can even fill any uneven areas, cracks, chips, holes, dents, or pitted areas with car bondo then sand that smooth . Use Lysol Power or any toilet bowl cleaner that has hydrochloric acid in it and it will etch and deep clean. From there tape up and pour.

@BeesKnees826 4 жыл бұрын

A couple of questions. Can you use this on your bathroom sink? Also, had it ever been used on tile floor? If so, can you tint it?

@mjp5129 4 жыл бұрын

Rae Cherrelle I would think something like Scrubbing Bubbles, would be ok. It’s not harsh. I wouldn’t use Comet or Barkeepers friend. How about glass ceramic stovetop cleaner. I don’t think it has abrasives in it. I doesn’t scratch my stovetop.

@elizabethkasper7094 3 жыл бұрын

do you fill chips before you pour the product?

@RefinishedBathSolutions 3 жыл бұрын

Yes fill any chips, cracks, dents, or holes with car bondo then sand it smooth then you can coat.

@mjp5129 4 жыл бұрын

My bathtub is an ugly green cultured marble. Can I use this for product for it?

@RefinishedBathSolutions 4 жыл бұрын

MjP51 yes. Ekopel is the best product for that application.

@larrydew6960 2 жыл бұрын

What about the underside edge of the lip? I'm painting the outside first. I was going to run a 2" wide tape lip to the back of the underside of the top lip. That should keep the Ekopel off the tub and allow me to coat the bottom of the lip with Ekopel. How low can the temp go while it cures? I'm going to move the tub inside but the temp is usually 62 at night, 68 or so during the day. Thanks

@RefinishedBathSolutions 2 жыл бұрын

It's up to you if you want to tape that off or do it first and let dry. The product dries in 24-36 hours but it can take up to 30 days to cure. The cure time does not affect when you can use the tub though. You can use the tub in 24-36 hours after you've poured. We recommend 72-75 degrees you can use a space heater with the door closed to achieve proper temp.

@ethantimm2780 2 жыл бұрын

Why not just paint the outside second?

@patriciagugliardo 4 жыл бұрын

What is the paper with the tape called? I need that also.

@RefinishedBathSolutions 4 жыл бұрын

Patsy Kakez it is a paper machine. They sell them at Home Depot and sherwin Williams

@kristiannabetch 4 жыл бұрын

Damn. A few minutes in and I feel even more stupid than before. I'm watching this because I used a new (lysol) toilet bowl cleaner to try and get stains off of my tub and ruined it. 😅🤦🏻‍♀️😭

@HKBr1nghurst 2 жыл бұрын

You are not alone. I did the same damned thing, and have now landed on the same video wanting to fix it rather than replace it. 🤣

@lutemule 3 жыл бұрын

I made some mistakes with mine but I am ok with the over all results.

@RefinishedBathSolutions 3 жыл бұрын

Any mistakes can be fixed by sanding smooth to the touch with 220-320 grit sandpaper. If after sanding you don't need more material then double the grit to 600 then 1500 then use any car buffing compound to bring the shine back. If after sanding you need more material we have a pour on touch up kit that is the same material just a smaller amount.

@cindiqq2292 3 жыл бұрын

Where do I buy Ekopek 2K? I googled said this is a German product, have to order overseas?

@RefinishedBathSolutions 3 жыл бұрын

We just started making here in the USA right in New Hampshire!! Here is our link: refinishedbathsolutions.com/

@jrocket7368 3 жыл бұрын

cast iron!?

@jamesbarfield19 5 жыл бұрын

Question: Getting ready to use the Ekopel . . . Prior to I had to strip the old paint/epoxy or whatever it was. the tub is not yet connected to plumbing so the acid etch step (washing) will be difficult. Given I just stripped the hole thing down, is this step necessary?

@RefinishedBathSolutions 5 жыл бұрын

James Barfield no as long as the tub is good and clean it will be fine. If it’s not being etched so customers sand the surface to make sure it is very clean. I would go over it quickly with 80 or 100 grit paper by hand then just wipe it out.

@timwallace6246 4 жыл бұрын

How thick do you leave it on the bottom? Thanks in advance.

@RefinishedBathSolutions 4 жыл бұрын

Tim WALLACE about an 8th of an inch

@timwallace6246 4 жыл бұрын

Thank you for your quick response. I'm doing my first tomorrow.

@EDWINP71 4 жыл бұрын

Bro, did you ever try to use an air gun to paint the bathtubs you will save time and not use much material.

@RefinishedBathSolutions 4 жыл бұрын

just me Jaja thanks for the feedback. No even the best spray material every created will eventually peel up. I owned a company that applied spray finish for 15 years. We produced over 10,000 units. We used Ekopel for 1 month and then sold all of our spray equipment. I will never spray a tub again. Give us a call when your ready to stop breathing the chemicals, and provide your customers with a finish that you can stand behind. All spray finishes will eventually peel. To peel Ekopel you need a blowtorch.

@IsaacBowerArt 4 жыл бұрын

@@RefinishedBathSolutions FYI, the kit I was sold had significant chemical fumes. I confirmed with your help line that the can contained Ekopel, not the old tub cast product you used to sell. I definitely needed a chemical mask, moderate fumes persisted for several days. Frankly the product didn't level as expected, I'm not very pleased with the results. Ive asked Sarah to try to track the batch and figure out why this had fumes and didn't level well.

@katieeck9846 3 жыл бұрын

I just did mine 4 hours ago in the garage. Went outside and a fly flew into it 😭 Wtf do I do??

@RefinishedBathSolutions 3 жыл бұрын

Aww that such a bummer! But it's fixable! Heat up the area with a heat gun or hair dryer then take tweezers and pull the bug from the finish. After that you can sand the area smooth with 220-320 grit sandpaper if you need more material we have touch up kits on our website you would apply and it will look good as new. If you don't need more material after sanding then you can double the grit of sandpaper to 600 then 1500. Next use any car buffing compound to bring the shine back.

@lf-1942 4 жыл бұрын

If you use this on a cast iron tub, what do you use to keep it clean? Your website stated "Avoid abrasive cleaners and clean regularly to maintain a long lasting shine." But it did not give any suggestions on what to use. So what would you use? Thanks.

@RefinishedBathSolutions 4 жыл бұрын

I use scrubbing bubbles or tilex.

@lf-1942 4 жыл бұрын

@@RefinishedBathSolutions thanks for the answer. I guess soft scrub is out. What happens if you mess up your tub? How do you fix it? Do you have a video on that? I haven't gone through all your videos but I haven't seen it yet. Thanks again.

@prudy123 4 жыл бұрын

I was wondering if I can use this product to the bathtub white tile wall?

@RefinishedBathSolutions 4 жыл бұрын

Yes we have a video for that application as well. It’s more difficult but will hold up indefinitely.

@gissie391 3 жыл бұрын

Etching?

@RefinishedBathSolutions 3 жыл бұрын

To etch the surface use Lysol Power or any toilet bowl cleaner that has hydrochloric acid in it.

@bdock10 3 жыл бұрын

Sand or no is all I need to know

@RefinishedBathSolutions 3 жыл бұрын

I would recommending sanding smooth to the touch even if its pretty smooth ruff it up with 400 grit. Then give a deep clean and etch with Lysol Power or any toilet bowl cleaner with hydrochloric acid in it.

@misslisa5236 3 жыл бұрын

So if my clawfoot tub is not installed, do I have to tape up the drain or could I just let the excess run out into a pan underneath my drain?

@RefinishedBathSolutions 3 жыл бұрын

If the clawfoot is uninstalled then yes, you could put something underneath to catch the material if it's installed DO NOT DO THAT

@saintejeannedarc9460 5 жыл бұрын

There doesn't seem to be a thing wrong w/ that tub. I wish my clawfoot looked as good, but someone did a diy kit and it has flaking paint.

@cowboyiam2085 4 жыл бұрын

I have questions but reading the comments clearly, no one answers any fucking questions so good video but I don't understand enough to make a decision.

@RefinishedBathSolutions 4 жыл бұрын

If you have questions you can ask though here and I'll get back to you asap or you can call us at 877-882-2278 or email us at sboudreau@refinishedbathsolutions.com