In this video I'm comparing the cutting capabilities between my old "7W" laser and my new 10W Endurance laser
Пікірлер: 14
@Endurancerobotschannel3 жыл бұрын
thank you for your video!!!
@HoarderOfHobbies3 жыл бұрын
No Problem! There's a lot more to come (mainly because I like playing with lasers!) LOL
@3dPrintCreator3 жыл бұрын
how did you manage to not cut parts of the circle on the top side of the burn? I know, because of the trapezium kerf, this kind of problem happens on the bottom part, but I have never seen it on the top of the kerf.
@HoarderOfHobbies3 жыл бұрын
Ahh I think what's not clear in the video is I am turning that cardboard sheet over when I grab it - what I'm showing is the bottom :)
@sitgesvillaapartmentneilsc79243 жыл бұрын
I would have put a bullet in that compressor by now! nice little comparison, what was the other laser brand?
@HoarderOfHobbies3 жыл бұрын
Too noisy? LOL It's supposed to be one of the quiet ones too! :) there's no brand on the other laser - I got it from Banggood website (China)
@sitgesvillaapartmentneilsc79243 жыл бұрын
@@HoarderOfHobbies ha! I meant the air compressor not the Hailea little one, i just cant stand the noise of the hiss, damages you ears hearing big time, im the admin on the Endurance site. good review thanks also good to know its a Bangood model. chinese ones are so awful really, trouble is people don't look father that the big 20 watt label which is input power normally not output! I see George has sengt you one with a monster fan on it....nIt will work well, next time a C02 Laser.... pop one of those on your CNC and away you go...I have a smaller one than yours, 1.5 mts x 1 mts workbee but still very good fun and good at what iI use it for, the CO2 though is in a big cabinet, its way too dangerous not too be really, cant see the beam and what it touches catches fire in seconds.
@nobullreviews20243 жыл бұрын
I would like to see cutting of ply not cardboard
@HoarderOfHobbies3 жыл бұрын
I am working on that right now - but I'll give you a hint - I'm making it through .25 plywood in like 4 passes at 8ipm
@Les547423 жыл бұрын
How did you connect the laser to the breakout board ? I have a usb breakout board but not much info on how to connect it. ( I have a 7W diode laser). Thanks
@HoarderOfHobbies3 жыл бұрын
If your laser box has the PWM or TTL wires, then you should be able to connect them to any outputs you have on your breakout board - mine only has 0 and 17 for outputs so I connected mine to 17 and then in Mach3 I just have to turn on that output and tell it which pin (17) to use... Are you using Mach3?
@Les547423 жыл бұрын
@@HoarderOfHobbies Thank you for the reply. I have the PWM connection on my breakout board for the router.. I don't use the board to control my router so I will give it a try. Regards LesDouglas
@Les547423 жыл бұрын
Yes I am using Mach 3. The breakout board is WiXHC.
@HoarderOfHobbies3 жыл бұрын
@@Les54742 Cool - looks like they have a few different models and I can't find the manuals for them - but there should be some outputs (like 3, 4, 5,6) and those will be mapped to pin outputs from the computer(like for example, output 3 on the board is actually output 17 on the computer) there should be a pin to output chart for that in your manual - if you send me the manual I can tell you for sure (hoarderofhobbies@gmail.com)