Harold Brookshire (Ultradyne Cams, RIP) was a genius at that closing ramp on his lobes, which I think were almost all asymmetrical. Even his early work at General Kinetics and later work at Lunati (VooDoo, etc.) had those carefully calculated closing rates.

Thanks for the insight Steve, looking forward to the next one!

Absolutely, @50 & @200 numbers are the biggest factors. The time(duration) that the valve spends in these areas is huge as compared tonthe time the valve spends in the lift area say .100" either side of full lift. Hence , head flow number at peak valve lift is not as important to think about as flow figures within the range up to 'about' 80% of peak lift. Great vid 👍

Awsome info thanks!

I really enjoy the camshaft profiles differances per application..Would you have or know who would be able to grind a cam with the LS firing order 4-7/2-3 swap for 572 mopar wedge

Good video. So, how many degrees of rotation does a camshaft stay at maximum lift? It seems like it is there less than 1 degree of rotation. Help me understand please.

This is from Steve Morris engines u tube. Good stuff. Check him out

I'm new 2 your channel quick question for you I have a 2007 Chrysler Aspen 5.7 Hemi I'm looking to put a cam in there from the Jeep Grand Cherokee with tha 392

Does Anyone Know If A .315" Lobe On A 252 Advertized Duration (200 @ .50") Is A Harsh For Rhe Valvetrain? Its In A 1.65 Rocker. This Is A GM 3800 V6 (231CuIn). Im Specing A Camshaft And Im Constrained To Very Short Durations To Keep My Overlap In Check For My Desired LSA. Its A Daily Driver Turbo Car. Originally I Speced The Intake Lobe .344 With 252 Duration (202 @0.50") But I Figured That Was Far Too Agressive On The Valvetrain For A Daily Driver.

Is there no mean of dampening the bounce?

Awesome video, explains it perfectly

So Ive just bought a pair of reprofiled camshaft’s for my Vauxhall XE engine and they are sold on a fast road basis and fit to the engine on it’s standard timing markings because the clearance are said to be safe. Out of interest before fitting, i measured the lobes on my original cams and they were 44mm, but the upgraded cams had shorter lobes at 40mm. Now I would of thought the upgraded cams would have higher lobes, or atleast the same size for valve lift. Can anyone explain why this is? Do the upgraded cams give me more valve opening durations over the standard ones? Turned engine over by hand several times and it feels perfectly ok as in no valves colliding with the pistons. I’m just a bit curious. Piper cams they are and claim to give a power increase of 12bhp. I’ve already got a direct cold air duct and a large bore 4-2-1 exhaust manifold with a 2” straight through pipe. I’m excited to see how well the power gains with be. But very curious about the lobe sizes being different. Also, it occurred to me that is it necessary to change the valve springs to accommodate the upgraded one or would the standard springs be ok?

27👍's up Steve Morris

Someone should get a high speed camera and set up a test rig to show the bounce, I'd like to know how someone figured out about the bounce, how the hell would you know that. Be cool to see it in high speed

damn good video

1970 340 374 hp Tommy Bosher look in the mirror say Dodge Chrysler Plymouth DART 3 times.

Really ? Opening lobe on left side, you must have a reverse rotation engine ?? Most engines turn clock wise when looking at the front of the engine ?

I hope this series ends in the actual math and formulas that describe the entire lobe. Duration at X lift doesn't tell me enough about what a cam does.

Here is what I dont understand. Why does the cams for high performance cost a shit ton more than a basic one made of the same metal? No matter the specs. It is the same trouble and material no matter the setup. Either way all you do is put the numbers in the grinding machine. Why charge more?

Nothing about a camshaft if "OBVIOUS" to anyone who decides to watch a video, that alleges to explain how they work.

Ok this is a thing with "engine builders" intake center line is not relevant to lobe separation angle absolutely. And here's why, lobe separation is ground into the cam and can't be changed. Intake lobe center is ground into the cam but it can be changed. So if you have a 3500 hp drag and drive car, and it constantly shakes the tires you can retard the cam 4 degrees to take out some of the torque, but you're not changing the lobe separation in the least. This isn't that complicated !