How to Change Front Brake Discs & Pads

Рет қаралды 598,951

Күн бұрын

Brake pads consist of a backing plate and friction material. It is the friction material that comes into contact with the brake disc. Overtime the friction material wears down and your brakes become less effective at stopping your vehicle. The manufacturer of your vehicle will specify a minimum thickness of the friction material before the brake pads need to be replaced.When checking your brake pads, you should look at the inner and outer brake pads as they can wear at different rates. If your vehicle is fitted with alloy wheels looking at the thickness of the outer pad is not enough.Brake discs are made of cast iron. Like brake pads they can wear over time. Depending on your driving style, brake discs have a longer service life than the pads and do not require replacement every time pads are replaced. When you are inspecting brake discs you should check both sides.
Find the right part for your car here: www.eurocarparts.com/

Пікірлер: 117

@mickeyh1961 8 жыл бұрын

fantastic video, especially someone like me who knows very little about cars, this was a good step by step explanation and done in a logical manner for a novice where the presenter does not assume you understand how the job should be done. very helpful.

@bezaleeluk3696 4 жыл бұрын

if you know very little about cars you cannot know where this person did things right and when he did things wrong...used the wrong lubricants and did not ensure safety critical bolts were correctly tightened and not over or under tightened.

@mattbartholomew5707 10 жыл бұрын

Excellent "How to" very clear and easy to follow only step I did differently was I greased the Hub after cleaning it of old rust so next time (If there is to be one, car has 200K miles) it should not have rusted up and no need for the hammer.

@janetjones6658 2 жыл бұрын

Studying at the moment Motor Technology. I am also doing my work experience. This video is just how I was taught in the work experience. Although we did not put grease. Great job 👏 👍 😜

@philnewman1110 9 жыл бұрын

An excellent video clearly demonstrated by someone who is of a very good skill level. Very helpful and useful video, many thanks!

@darthporkius 7 жыл бұрын

Thanks for the video. I've always liked cars and driving. I've always wanted to get into the mechanical side of things. I'm gonna let a pro change my brake pads this time but next time I'll do it my self.

@yusuihang 10 жыл бұрын

Really nice video. Excellent contents and presentation. Appreciate the professional, two camera filming. I must have watched at least 30 videos on youtube on brake replacement (about to do my very first brake replacement), and this video is one of the best. The only two details that I would add: 1) put anti-seize on hub before installing new rotor (could the brake grease be used instead?); 2) clean and then lube the caliper pins with the synthetic brake grease.

@001maz 10 жыл бұрын

My present shed (kia picanto) took me 5 days of swearing changing the rear pads and disk, didnt know about rewind calipers, worst bit was when i put brake fluid into the coolant bottle, and eventually lost all the pressure in the system. ps The rear off-side disk protection arch had rotted away and bits fell into the pads wrecking disk and pads. Also , no mention of the thin metal liners I got to fit over the cradle before inserting the pads and the hours spent grinding bits of of the pads to make the (cheapest) pads fit smoothly. First thing you need is a long metal pole about a metre long to crack yer wheel nuts open after the tyre fitter put 160 1bs on it.

@Yeoblade 3 жыл бұрын

Which garage do you work at ? Quick fit?

@steveward676 9 жыл бұрын

Brilliantly done step by step guide for diy. Well done to you guy's !

@premierfuncasino Жыл бұрын

Really excellent, patient, methodical, easy to follow guide. Many thanks

@ciaomarco4194 7 жыл бұрын

Faced with the daunting task of replacing my front break discs today, this was invaluable, thank you. Video was clear, well-lit, and fully detailed. The in-video link to parts department was useful too!

@mfeastham 8 ай бұрын

Brake

@arunashantha349 8 ай бұрын

sMe

@SylvLivingstone 9 жыл бұрын

glad he reminded us to pump the brakes (as the other video I watched didn't )... All in all, well done (though kinda confused about the WD40 side of things?? are we meant to spray it on the rubber or not (was just reading other comments on here...

@sakadabara 8 жыл бұрын

1) He didn't greased the sliding pins - one of the major causes for uneven wear of the break pads 2) repeatedly places brake discs and busy side of the pads on dirty floor 3) the rubber seals of the pistons were worn out

@grazianolaudisio3644 7 жыл бұрын

Nikolai Tsakov Thank you for the extra advice! I think this video was useful.

@bezaleeluk3696 4 жыл бұрын

he also appears to have used standard low temperature grease on the end and backs of the pads... that stuff will melt and flow and eventually burn off! Also leaving the brake oil reservoir lid off in these types of jobs is a bad idea. Invites contamination of the hydraulic oil and risks spilling hydraulic fluid on paintwork if it squirts when the piston is pushed back. There is NO need to remove the cap, just slacken it off to let air pressure escape on piston pushback is more than sufficient! And he should have used torque wrench tightening the carrier bolts as they do need to be quite tight but not too tight as it can strip the threads in the carrier if you over cook it with a breaker bar like that.

@desividesi01 6 жыл бұрын

The very best "How To" tutorial to date. Keep it up guys, you are real good,,and thank you.

@fredborne90 6 жыл бұрын

great mate 10/10 no razzmatazz no crappy jokes just plain simple down to earth how to do thank you kindly your a gent

@screwsnutsandbolts 6 жыл бұрын

Excellent and helpful videos, thanks

@jamesmcrory8990 4 жыл бұрын

Remember to put some anti seize on the hub before you put the disc on, that will prevent it from sticking to the hub and make it a lot easier to get off next time. But don’t get any anti seize on where the friction will take place.

@andyedge7912 9 жыл бұрын

Great vid, both our cars are due new pads soon thanks .

@nathanwilliams1878 9 жыл бұрын

Probably should have compared the new and old pads before cutting the cable off mind, can't return them if they are wrong then :)

@roboCL0WN 11 жыл бұрын

This video came up as an advert and I really enjoyed it, very well put together.

@Front9_golf 10 жыл бұрын

At last a clear 'how to' video!!! I'm defo doing this shit next week!!!

@tygertygerburn 8 жыл бұрын

Excellent video the makers should be proud of their work.

@piecetoyou8285 7 жыл бұрын

Great and useful video,But a little criticism, Where a mask when cleaning debris,especially where around brake components pad fine particles mixes in with rust, Give piston a wipe befor pushing it back in, There were no use of loctite on certain bolts,heat and vibration can cause used bolts to work there self loose. Apart from that nice clear instructions, Thank you

@Eupmem Жыл бұрын

Excellent video, detailed and efficient, thanks !!!

@mikesoja 9 жыл бұрын

Wonderfully done.

@laodicea3513 8 жыл бұрын

Thank you so much posting this video.. great job !!!!

@stevespeck3586 8 жыл бұрын

Great, clear, practical video. Did I miss mention of torque settings - particularly for the carrier and the caliper bolts?

@bernicelavignemansueto4781 10 жыл бұрын

thanks very nice video ive learned easyly

@ryangeddes7277 10 жыл бұрын

Very useful, thank you!

@georgiivanov1902 8 жыл бұрын

Great video! Great detail! Thanks a lot!!!!

@helenahusky2787 8 жыл бұрын

Very detailed video....

@mfeastham 10 ай бұрын

What about checking fluid level before compressing caliper to save stripping your paintwork with overflow?

@MyJammy12 2 ай бұрын

Open the cap in the bonnet and put a rag in the top

@avtarkalsi2853 4 жыл бұрын

Brilliant guide

@HansjeVdTillaert 8 жыл бұрын

Great video!!!!

@jr5389 Жыл бұрын

Excellent video and music relaxing 👍🏴󠁧󠁢󠁳󠁣󠁴󠁿😎

@JCMFix Жыл бұрын

Super professional.

@gerryreggea 8 жыл бұрын

Best video i've seen.

@mouradsaber1235 Жыл бұрын

Great job, thanks.

@jocalibusohump 7 жыл бұрын

thanks very informative

@thelordofdarkness141 2 жыл бұрын

What a great video

@amana1480 3 жыл бұрын

No checking for disc runout, by using a dial test gauge?

@marcozrx1100 8 жыл бұрын

i tried that version on my momobike ,,, i never replaced the reservoir cap before i slowly pumped the brakes, same as this vid ,, but my fluid just spilled out everywhere ?? i recommend do cap up before pumping ?? ,, good vid tho apart from that

@tomp.8129 9 жыл бұрын

In case no one else noticed the seal on caliper piston is failing, should have been replaced as it will start sticking before next pad change is due. What good does spraying on rubber seals with WD do?

@Techtablets 9 жыл бұрын

Tommy P Yes, infact it rips @18:09 a little when he puts it on....

@sudarshans226 8 жыл бұрын

Good video

@thelimit6593 7 жыл бұрын

I've always used copper slip on the back of the pads and a little when fitting the disc and nuts will help the next time they are removed,if your replacing both the pad and disc once you've removed the top of brake fluid filler cap you could pry back the cylinder prior to lifting the calliper by placing a large flat bladed screw driver between the old disc and pad. It's old school not recommended if your just replacing the pads.

@frederickjamal1808 2 жыл бұрын

Sorry to be so offtopic but does someone know of a method to get back into an instagram account?? I was stupid forgot my account password. I would appreciate any help you can give me

@xzavierjacoby721 2 жыл бұрын

@Frederick Jamal instablaster =)

@frederickjamal1808 2 жыл бұрын

@Xzavier Jacoby I really appreciate your reply. I got to the site thru google and im waiting for the hacking stuff atm. Takes quite some time so I will reply here later when my account password hopefully is recovered.

@frederickjamal1808 2 жыл бұрын

@Xzavier Jacoby it worked and I actually got access to my account again. I'm so happy! Thank you so much you saved my account :D

@xzavierjacoby721 2 жыл бұрын

@Frederick Jamal You are welcome =)

@danielhearnden3776 10 ай бұрын

Suspiciously skilful with the lubricant 😂

@aboom257 8 жыл бұрын

top job

@techtitanuk5609 23 күн бұрын

It's super easy to replace break pads, garages charge over a hundred quid

@audioman6007 8 жыл бұрын

are these pagid brakes any good as they cost almost as much as brembo brakes

@davidcollins4227 7 жыл бұрын

Shouldn't the bleed screws on the calliper be opened when pushing the piston back as it could damage abs module or flip master cylinder valves when pushing brake fluid backward?? Or is that rule only applys when doing rear brake pads , anyone ??

@Twongz_does_anything 5 ай бұрын

DONT THINK SO

@paulhammond1966 6 жыл бұрын

I need to replace steering rack gaiter at same time. Am I about there once discs are off or is there a lot more stripping down to do. I have heard there is a kit you can use to replace gaiter without stripping down the arm. Is this true??

@didar389 9 жыл бұрын

hi thanks for the video but you didn't torque the any bolt .

@jefffork5143 10 жыл бұрын

great back ground music, who is it by, album name, or artist?

@markholyoak9790 2 жыл бұрын

don't forget to torque your bolts up and put thread locker fluid onto the brake bracket bolts

@bobikzielarz 4 ай бұрын

This boy awesome.

@001maz 10 жыл бұрын

I've always managed without using a torque wrench but felt a bit guilty (thinking thats what the pros use), now it looks like I was right all along, 40 years fixing sheds.

@bezaleeluk3696 4 жыл бұрын

tightening bolts by feel is a gamble, a true professional will use a torque wrench on safety and reliability critical nuts and bolts like the carrier and slider bolts. Too loose and they could self loosen and cause brakes to fail, too tight and could strip threads in carrier or stretch bolts or make a rod for the next guys back if you over cook the torque but get away with it... the next mechanic will likely have to use heat to get the bolts undone next time.

@leerichardson4118 4 ай бұрын

Didnt clean round the piston seal with nylon brush to get rid of old crud!

@brucewayne7838 4 жыл бұрын

great video !! alfred will find it very helpfull

@alanfrancis9225 3 жыл бұрын

Good video but Where’s the torque wrench and why doesn’t he clean and use suitable grease on calliper slider pins?

@Drainingtheswamp2022 10 ай бұрын

No allen grub to hold the disc in place?

@unda25 5 жыл бұрын

What size are break disk mk4 1.9 TDI 2001 6 gear manual UK

@arturocruz1935 3 ай бұрын

Its for a 2022 Nissan Altima Pop

@intheblinkofaneye2630 6 жыл бұрын

i thought this was a great video as i have to change my front brakes,

@juliadennehy 5 жыл бұрын

Have a look at your cv boots while working on your brakes... this one looks like it may be leaking...

@train4905 5 ай бұрын

Exelleny😊

@nigelhopkinson6614 3 жыл бұрын

I wonder why manufactures bother with torque wrench settings ?

@paulomorais0 5 жыл бұрын

great video. Can't remember the end, the music made me drowse off though.

@saveriosalerno9232 8 жыл бұрын

COMPLIMENT!

@adamsala9291 Жыл бұрын

You didn't put any grease on caliper pins?🤢

@SteU4IA 9 жыл бұрын

For the love of God don't spray WD 40 on slider pin boots!

@dionjoseph9534 9 жыл бұрын

good day just wanna know why not to spray WD 40 on the boots?

@SteU4IA 9 жыл бұрын

dion joseph Hi, the rubber boots, like all rubber things, is oil-based product. Because WD-40 is petroleum (ie. oil) based and since like-dissolves-like, WD-40 and any petro based lube will eat away at the boots. What you want to use is something safe for rubber parts like pure silicone lube or fully-synthetic brake lube.

@wilstw 9 жыл бұрын

Ste .L ..

@SteU4IA 9 жыл бұрын

Willie Stewart Yes?

@bullitautorepairsmobile4989 5 жыл бұрын

Not a professional job at all ,Can seem at least 4 things wrong or needful doing .answers on a post card ,ha ha ,failing that just reply

@lennonpolo 6 жыл бұрын

Do not put WD40 on rubber!

@thomasDSoundDesign 9 жыл бұрын

Is the vehicle in park (got hand brake on) ?

@ad5772 6 жыл бұрын

Shovel provides a

@edgarabramz 8 жыл бұрын

Soks

@EppingForest304 6 жыл бұрын

Should've cleaned & regreased the caliper slide pins with silicone paste

@bobikzielarz 4 ай бұрын

When you got the right tools for the job.... It's obvious.

@MTVCHANNElNEWZ Жыл бұрын

Oil tank 8

@stevehawcroft 4 жыл бұрын

I didn’t know Lee Sharpe was a mechanic!

@marcuswoodgate4026 3 жыл бұрын

Not exactly rushing this job is he 😂

@train4905 5 ай бұрын

Exellent,sorry😊

@lexingtoncharles2643 2 жыл бұрын

Roter weet

@fudgedog123 8 жыл бұрын

good instructions. But that car mings.....

@lonewolfe7343 4 жыл бұрын

Should have changed his gloves, all that crease going onto the new disc and pads,....

@jzilla1234 6 жыл бұрын

Erm wd40 on to the rubber?

@lonewolfe7343 4 жыл бұрын

Should av used Carboflo for rubber...

@davefiatforum 4 жыл бұрын

this a how not video? no torque wrench essential for beginners, no thread lock used on bolts! you should always remove clean and grease the sliding pins. The bleed screw was all corroded and cap missing. you should at least clean that and put penetration oil on it so when the need may come to use it its not stuck.

@FunkyTonLow 7 жыл бұрын

is this auto porn?

@jesusloveyou9523 7 жыл бұрын

my man probably charge £15 for 30 min

@davidsheen7682 3 жыл бұрын

volume poor

@johnsmith-fu6hu 3 жыл бұрын

No torque wrench how you measure the force? Just by hand? Hmmm ... are you a chef 👩‍🍳 by trade or a house wife fitter? 😂

@pontiacgaz 3 жыл бұрын

So......the safety goggles??? Are they just for show, not the 1st vid I've seen that say you need them but don't wear them, better dig mine out and lay them next to me when I do mine today 😎