to stop the steel tie from loosening a bit, as you pull it htrough push the ball bearing into the housing, this stops it slackening off a couple of MM, best way to wrap is to overlap 50% and this will give a consistant double thickness from start to finish, no highs and no troughs, when finished run engine and when dry coat with silicon spray. . .

The best video on youtube for the subject. And then there was the cool-bus at the end for a suprise.

I like the way you do your metal ties.... Tricky little things.... Good video.!

A great help, I wouldn't have wet it but see the sense in doing it . Thanks

Great video, thank you.. Would never have known about wetting strap first.

this helped me alot i was struggling at first but after i watched this it helped me a lot lol but thank you for your advice man

NOW THIS is a good video!! F***YEAH

Solid advice gonna be wrapping mine soon

About to wrap something cheers for the help on how 👍🏼

Dude so i have a diesel generator what i changed the exhaust on from going out the top stack like to going underneath (its mounted on a trailer now) and this video is a very well put together video! Its my 1st time ever wrapping something and will jot be seen except by me for maintence Thanks for the Great content!!! that bus look awesome to!

looks good nice job!!

Nice job. I'm doing my motorcycle today and will use some of your tips. Peace.

Mi duda era como ajustar los sinchos pero eso de mojar el rollo para que no resbale es un gran consejo ... Excelente video

Thank you for the tips

Wrapping my intercooler tubing on my 7.3, thanks for the help

Great vid!

Awesome✌️

Fantastic

Thank you sir!!

Very nice on the ties

Best dam rapper I've ever heard of.

Great job,

Nice video! How long do you soak the roll?

I fibreglass for 25 years and all the it makes you itch comments are hilarious. The sun was beaming down so I used my turbo blanket as a hat and wrap as a scarf.

Wait the wrap is directional now? I have never heard that only one side is the face-down side?

My exhaust wrap smoking when are turn the engine???

So... i have a 400hp MONSTER size turbo diesel in a 40' Mainship 25k#. I am getting ZERO boost. The old guy i got it from replaced the 160hp engine. This engine came with dry exhaust manifolds. He put on wet manifolds. My knowledge of engine physics tells me he is sucking all of the heat out of the exhaust charge and the turbo (while spinning freely) isnt spooling up. The marine "rules" say you must have a wet exhaust manifold. My solution is to use the double wall (wet manifild with no water) and wrap it to achive roughly the same thermal result.... and finally get some power and fuel economy. I will probably use mig wire tails as extra ties when i run out of the 10 included with the 50' of wrap. Any thoughts anybody?

I’m a sixty your old woman and I look to get my 95 dodge ram 1500 exhaust wrapped and was thinking to do it myself …. Well my skin is sensitive so I won’t be doing it.😂 You did a wonderful job wrapping so I don’t know where to go and how much it would cost. Thx

How does the wrap hold up to winter weather?

4:20 I watch to much Tim Heidecker for that tune to hit home

is it ok to breathe in all that fiberglass?

Ain’t no way he used the Stickman sniper theme song 💀

Uhhhh, what if I forgot to soak it in water/ damp it.. ? I already sprayed it two coats now I’m waiting for it to dry/ looking up vids in general again and now I see you had to damp it- I didn’t..

wat you could do that doesnt look too mush like a heatshield is put a pipe cut in half length wise over the wrap and fix it to the pipe with hoseclamps , i think if you rake sumting along the pipes or bump intoo them it will damage the wrapping , having it exposed to the sun prolly whont do it any favors either and have the black turning intoo grey or white , the "shields" over them should prevent most of that , could paint the shields in either the exhaust blue or in the bus blue / black too could have a set of custom shields made somewhere with a cnc plasmacutter / waterjet and have the name of the channel or bus cut intoo them before rolling them halfround or use a brake to give them a multi angle just thought of sumting weird : if you ever decide to have a patio next to the bus under an awning with a propane bottle style wood burning stove you could make a hookup for the stove intoo the same exhaust pipe (hidden behind the shield ) and not have to worrie bout smoke blowing intoo the bus

Water allows it to become more “flexible”

Amber's fault for getting burned that burn was on the outside part of her leg

Amber should be wearing long pants on a motorcycle

Sorry but that looks goofy and unessasary... I don't get it