Motorcycle Exhaust Wrap How To

Рет қаралды 36,235

3 жыл бұрын

Motorcycle Exhaust Wrap How To - In this video I show you how to install some exhaust heat wrap on your motorcycle exhaust.
Exhaust wrap comes in a few different sizes, colors, and lengths but most commonly you see 2 inch wide wrap being used and most available. Be sure to use gloves in this process as many wraps are made of fiberglass which will imbed itself in your skin and cause a lot of irritation.
Wrap options:
amzn.to/3ezkMng
Safety wire pliers:
amzn.to/3hP4pVz
High Temp Exhaust Paint:
amzn.to/36KjykL
If you found this video helpful or simply wish to support the channel further feel free to donate to the "Tip Jar" via the paypal link below! Anything is very much appreciated!
www.paypal.com/donate?hosted_...
For updates on this project as well as others be sure to follow along on all the Brick House Builds social media platforms!
Instagram - / brickhousebuilds
Facebook - / brickhousebuilds
Website - www.brickhousebuilds.com/
#brickhousebuilds #exhaustwraphowto #caferacer

Пікірлер: 125

@adrian.vasile 3 жыл бұрын

I always fold the ends at start and finish. That fiber tends to tear easily. And don't be afraid to dunk it if you have no buddy to help, after the wrap I always leave the bike running to dry it up. Great work on the build!

@BrickHouseBuilds 3 жыл бұрын

I sometimes fold at the end but good tip for sure

@Thewatson77 3 жыл бұрын

Actually probably one of the most thorough vids about exhaust wrap I’ve ever seen. Great video BJ 👍🏼

@djuhasz3706 2 жыл бұрын

Thanks for showing this off. I have started using the rubber gear ties in place of zip ties for holding things temporarily. Might save you a few bucks in the long term.

@strshooter7399 2 жыл бұрын

Great demo on using exhaust wrap. My 2002 Connie runs it’s HOT exhaust headers so close to the inside of the fairings in places, I’ve considered doing this for years. I don’t want to pull the fairing pieces and then pull the exhaust to then wrap 4 pipes, but at least I’ve seen how its done! Excellent tutorial ! Thanks 👍

@BrickHouseBuilds 2 жыл бұрын

Thermal protection is definitely where this stuff shines. Thanks for checking the video out and I'm glad it was helpful!

@SMHman666 2 жыл бұрын

Thanks for uploading. That CX is lookin' good !

@BrickHouseBuilds 2 жыл бұрын

Thanks Robert!

@arthurzielinski8187 3 жыл бұрын

Dude, that’s so good 😍 love this build

@BrickHouseBuilds 3 жыл бұрын

Thank you!

@bellaggio1770 Жыл бұрын

I installed it recently on an XT250 and I can confirm that it DOES increase performance noticeably.

@BUILDNIGHT 3 жыл бұрын

Lookin’ good, bud…. Giving me the motivation I need for my 3 bike projects….

@user-vk5vh8gr2t 3 ай бұрын

Thank you. I will be doing my Triumph soon, got some good pointers.

@joachimboussoumah9994 3 жыл бұрын

"...and you end up scratching smthg else and that's not fun" haha nice one 😅👌🏻 Great vid, love those how tos ! Helps a lot with my cx 500 restomod project !

@BrickHouseBuilds 3 жыл бұрын

hahaha I try to provide that real world experience ;)

@edwardmulder3777 2 жыл бұрын

Yeh, I cracked up on that 1 too, heheh.

@richiebainbridge2608 3 жыл бұрын

You make a great teacher. Thanks.

@BrickHouseBuilds 3 жыл бұрын

Thanks Rich! Just trying to share what I know and continue learning each day myself

@stewkeene Жыл бұрын

So I was thinking of wrapping the exhaust headers on my BMW R1200RT and do a search for how to and look what pops up! 😂 thanks so much for the video and the share. I’m gonna give silver a try. It’s totally an esthetic thing 😁

@BrickHouseBuilds Жыл бұрын

Haha I'm everywhere! To me its just esthetic as well. Occasionally I like it for protecting stuff from heat as well.

@rebuildranch1225 3 жыл бұрын

Super cool, nice job!,

@BrickHouseBuilds 3 жыл бұрын

Many thanks!

@michaelmathews295 2 жыл бұрын

I've done a few of these. I've used stainless steel straps that are available in the electrical departments of your big-box stores. They're around a 1/4" wide and cinch up like zip ties except they lie really flat.

@BrickHouseBuilds 2 жыл бұрын

I have seen and used those. I've simply been on a safety wire kick lately

@yngvardharjo3704 2 жыл бұрын

Nice work man

@BrickHouseBuilds 2 жыл бұрын

Many thanks!

@cedricbdo7551 Жыл бұрын

Nicely done

@BrickHouseBuilds Жыл бұрын

🙏🙏

@SmallLoanSoftwareTraining 10 ай бұрын

Great video. thank you

@BrickHouseBuilds 10 ай бұрын

Glad you enjoyed!

@markfranks48 2 жыл бұрын

Thanks I have never seen this done before

@BrickHouseBuilds 2 жыл бұрын

Glad it was helpful!

@El_SantoTaco 3 жыл бұрын

I dislike wrap, but I love your work. So here's a like and a view.

@BrickHouseBuilds 3 жыл бұрын

Fair enough and thank you

@mikeohonda486 2 жыл бұрын

Nice job

@BrickHouseBuilds 2 жыл бұрын

Thank ya Mike!

@tjwrongwaymead8374 4 ай бұрын

Nice. I did my Vance and Hines 4cyl on my zrx1200r in white. It was a wrestling match. Just for looks. Pipe was ugly so...came out nice .Thanks.

@BrickHouseBuilds 4 ай бұрын

4cyl pipes can definitely be a big pain in the butt!

@robertadams4415 2 жыл бұрын

Thanks for the info good to know

@BrickHouseBuilds 2 жыл бұрын

Glad it was helpful Robert!

@DocJonesGarage 3 жыл бұрын

Lengen......dary chock full of good stuff!

@BrickHouseBuilds 3 жыл бұрын

Thank ya Doc!

@AdamNicholasSievers Жыл бұрын

Damn man, I saw your XS for sale a while back, and if I hadn't already built my own I would've been all over it. I also want a 650 silvering, and here you are again building all the shit I want 😩.

@BrickHouseBuilds Жыл бұрын

Haha I appreciate it! I just wish I could build all the things I want more quickly

@Butterfly07949 Жыл бұрын

Really like the idea of using safety lock-wire instead of the usual metal cable ties. Incidentally using wrap on a air cooled bike is a really good idea because us air coolers need all the help we can get to keep our motors looking cool. See what I did there 😂

@BrickHouseBuilds Жыл бұрын

😉 i see what you did there

@bellaggio1770 Жыл бұрын

Just installed on an air cooled 250cc bike and it makes noticeably more power.

@backcountryme 2 жыл бұрын

I have wrapped tons of headers on Midgets and Sprint Cars and other racecars for years. I always soak my wrap in water for about 20 min. Makes the wrap go on easier, and as the wrap dries it slightly shrinks and pulls even tighter. But that is just the way I have always done it.

@BrickHouseBuilds 2 жыл бұрын

I've heard so many more reasons to not saturate the wrap than saturating it. It is much easier to work with with a simply mist I just don't see the need to soak it.

@backcountryme 2 жыл бұрын

@@BrickHouseBuilds I’m still trying to figure out how to get the charging system on my damn XS400 street tracker build. I just need to order your regulator and get rid of the Rick’s on I have now. Electrical has never been my strength.

@edwardmulder3777 2 жыл бұрын

Yep, that's the way I did mind too, cepting my bike wasn't operational so stuck most of it in the oven. Plus I had already derusted and rust primed and heat treated them with hi temp paint beforehand

@edwardmulder3777 2 жыл бұрын

@@backcountryme I think electrical is a bit of a ? for most guys, esp me.

@chrisfitzmaurice7484 Жыл бұрын

Cool music!

@BrickHouseBuilds Жыл бұрын

Glad you enjoyed!

@goldeniron8989 Жыл бұрын

Really Great Job 👍 Thank you so much for making this video to show us. Just one question so mine has a bunch of metal ties I see you just use a few are they not really needed?

@BrickHouseBuilds Жыл бұрын

If you wrap it correctly you only need ties at each end. Careful placement is important as well

@GlesgaNews Жыл бұрын

Enjoyed your video and channel. I would have painted over the top of the heat wrap with the heat paint. Makes the steel wire disappear, does look good though..GN

@BrickHouseBuilds Жыл бұрын

Thank you

@_JimS 2 жыл бұрын

Good job and nice build. What was Honda thinking putting the battery there.....YIKES!

@BrickHouseBuilds 2 жыл бұрын

I put the battery there. Very common spot and totally fine

@ecrusch 2 жыл бұрын

Fold the ends and use a normal flex-tie at the start to keep it tight. Putting the roll in a coffee can full of water is best.

@BrickHouseBuilds 2 жыл бұрын

Not good to fully saturate it. No point in doing that when a mist does the trick. Folding the ends is fair but zipties work just fine. This is a proven method I've used for years

@gopherchucksgamingnstuff2263 11 ай бұрын

I think it may help lower air temps near my radiator. GSXR 750. The header is right under my rad.

@BrickHouseBuilds 11 ай бұрын

It can indeed. I'd say worth a try

@tyroneshoelace4872 Жыл бұрын

Nice job on the video. Would this be nearly impossible to do with the pipes installed on the bike? Also, I heard mentioned that Titanium thermal wrap is better (no wetting, etc...). Any thoughts on that?

@BrickHouseBuilds Жыл бұрын

Trying this with the pipes on the bike is simply not worth the headache unless its a short section. I've never used the titanium stuff but Im sure its good

@andreyostrovsky6022 Жыл бұрын

Great work!!! I like your approach a lot! May I ask you a question? What kind of stand are you using? where to get it, and how expensive it might be? Thank you in advance, and sorry for asking too many questions , just hate to work on the floor . :)

@BrickHouseBuilds Жыл бұрын

Thank you! My lift is a black widdow brand and about 1800 with all the attachments. A simple solution is a wood table about 11 inches high that you roll the bike onto. I made my own and used them for years until I had to downsize my workspace and only have one station instead of 3. If you want hydraulic there are always a ton of used harbor freight lifts on marketplace for a few hundred dollars

@andreyostrovsky6022 Жыл бұрын

@@BrickHouseBuilds Thanks a lot ! Appreciate you help.

@TD-hn8jj Жыл бұрын

Grrat job. looks awesome! What was the total time on the job??

@BrickHouseBuilds Жыл бұрын

Thank you. Id say an hour or less

@marte1a256 2 жыл бұрын

Im blind and gona be doing this to my kids dirt bikes and quads. I know i can do it, just not good at working with gloves at all.

@BrickHouseBuilds 2 жыл бұрын

Even the best gloves make things a bit more difficult but they are a must for this job!

@OlderShadowRider Жыл бұрын

Excellent video, thank you; Just a query if I may? I noticed you did not wrap or paint your muffler? Is this by choice or other reason? On my bike, I've been trying to decide to vhf coat the whole exhaust, including the muffler but still wondering if I should wrap the muffler? Your thoughts.

@BrickHouseBuilds Жыл бұрын

Well this muffler is fully stainless and part of the look of the bike. No need or desire to paint

@BrickHouseBuilds Жыл бұрын

I would not wrap a muffler

@davehowie03 3 жыл бұрын

Can you explain the moisten vs submerging a bit more? Every other video I’ve seen says to submerge it in a bucket.

@BrickHouseBuilds 3 жыл бұрын

I just don't feel the need to saturate it to that level when a little mist does the job. My thinking is to avoid putting excess moisture on the pipes when possible. In my case this bike won't be running for a while still so if it was saturated that is just more exposure time to possibly corrode.

@davehowie03 3 жыл бұрын

@@BrickHouseBuilds thanks much. This makes quite a bit of sense. If you’re not gonna run it through a bunch of heat cycles to dry em out, probably shouldn’t leave em sopping wet on metal what could easily oxidize and rust.

@BrickHouseBuilds 3 жыл бұрын

@@davehowie03 precisely

@edwardmulder3777 2 жыл бұрын

After I soaked and wrapped mine, i shoved most of the piping into the oven and baked, heat treated them for a bit, otherwise ya could always use some other external heat. Soaking allows the material to stretch more and then dries to a tighter fit

@erickjos2696 Жыл бұрын

I've seen other recommendations about spraying thoroughly with high temp silicone after wrapping to prevent wrap from turning white. What are your thoughts on this?

@BrickHouseBuilds Жыл бұрын

I've never done that or had this turn white. I could see how that could be a good thing to do though

@erickjos2696 Жыл бұрын

@Brick House Builds ok thanks

@charlesvickery Жыл бұрын

Do you also keep spraying water as you go or only at the beginning stage of wrapping?

@BrickHouseBuilds Жыл бұрын

Im spraying to get the material to become more flexible and once its on the pipe in position I do not need to spray it. You see me unroll and spray as I can only hold so much at once

@Forward_Unto_Dawn Жыл бұрын

I had someone tell me that if I put exhaust wraps on my bike that the heat being trapped in the pipes will cause the motor to run hotter, and may even melt the factory wire harness, knock sensor wires/switches, and cause all kinds of problems with shorts, and alternator issues. I have a 2009 Honda ST1300 (Sport Touring). Is this accurate?

@BrickHouseBuilds Жыл бұрын

Well think about this. If your pipes are wrapped which helps decrease radiant heat you would see far less heat under your fairings. The person saying that is really reaching to make wrap sound bad. There are many great articles online about wrap though for you to do your own research so it doesn't seem biased

@Forward_Unto_Dawn Жыл бұрын

@BrickHouseBuilds copy that. The person who mentioned that is more like an "old school" type. I mean, he knows about that specific bike, but as anything, things get better as time progresses and more information and things come out to support what you're doing and proving.

@bear186 3 жыл бұрын

I Have NEVER done this 1st hand only seen in video… MY Opinion: I think getting sopping wet then putting on & RUNNING would make for a tighter fit … I’ve never done this….

@BrickHouseBuilds 3 жыл бұрын

So having done this many times I can say that getting it soaking wet does not make it more flexible than just a mist to relax it. As Ive mentioned in other comments I dont want to hold moisture against metal longer than I have to in order to avoid potential corrosion. Also this bike won't be up and running for a while longer so that only increases the possibility of corrosion

@rsanger9321 3 жыл бұрын

"I laughed, I cried, it was better than Cats"

@Texasphotoguy 3 ай бұрын

How long will that wrap stay black?

@BrickHouseBuilds 3 ай бұрын

Well its higher quality wrap so much longer than Amazon stuff but with care and limited exposure to water and stored inside it should last quite a while

@philipbgardner Ай бұрын

as i'm researching doing this to my bike, this is the only one I've seen where the wrap is not fully submerged to wet, and the header end doesn't go completely to the exhaust flange... by no means am I saying you did anything wrong, just wondering why you didn't go all the way to the exhaust flange, leaving a noticeable gap between the wrap and the head.

@BrickHouseBuilds Ай бұрын

You shouldn't submerge the wrap. I don't care what others say as this is what the manufacturers suggest. Those who dunk it are just being lazy in a way. As far as wrapping under the clamp I've never felt the need to do that. Often I'll end the wrap further down or even just do it where I need heat protection. No rules here.

@evangelosiatrou3004 Жыл бұрын

I hate exhaust wrap! 😡This stuff sucks!😡 I'm just playing😁. I was thinking about doing this to my bike. Thanks for the tips

@BrickHouseBuilds Жыл бұрын

Glad you found it helpful

@AndyMontes Жыл бұрын

I did it once but my wrap started to turn color to white until finally turned into ashes and felt off the exhaust. Why ?

@BrickHouseBuilds Жыл бұрын

I've seen that a lot with less expensive wraps. Another potential could be a lean condition causing even more extreme temps in the exhaust

@EvendimataE Жыл бұрын

is the tank sanded ang sprayed with cllear coat?

@BrickHouseBuilds Жыл бұрын

Yes, I go over it in this one. kzfaq.info/get/bejne/l6t_da2UqJPZfJs.html

@BrickHouseBuilds Жыл бұрын

kzfaq.info/get/bejne/hZiKpNyiurnbfXk.html

@I_Am_The_Real_Steve_Keating. 2 жыл бұрын

Love the Aquafina bottle full of piss behind ya lol that's when u know ur at a quality shop, when the mechanic can't even peel himself away from the job long enough to piss ffs lol

@BrickHouseBuilds 2 жыл бұрын

I don't know why people have focused on that extremely small detail of the video. Its water with orange flavoring in it.

@anaphrodisiacxyu 2 жыл бұрын

POV me: distracted by the Aquafina bottle filled halfway with yellow fluid on the back counter 👀

@BrickHouseBuilds 2 жыл бұрын

Orange vanilla mio

@Noel127 Ай бұрын

Biggest issue with wraps is moisture I don't believe spray is a good idea.

@BrickHouseBuilds Ай бұрын

If you completely saturate it or ride in the rain it's not good. A gentle spray like shown is best. This bike wasn't going in the rain

@DangerZONEpixel 10 ай бұрын

This whole process becomes 10 x harder when u have OCD.

@BrickHouseBuilds 10 ай бұрын

As does life!

@duosable 2 жыл бұрын

the wrap is going to create ugly burnt marks on stainless steel downpipe. needed to sand and polish to remove them.

@BrickHouseBuilds 2 жыл бұрын

Correct but if you have them wrapped thats not a concern

@duosable 2 жыл бұрын

@@BrickHouseBuilds Yes, but one last issue should be concerned is that it will create rust spot if the wrap is wet for certain amount of time. I have no idea how long would it take for a rust spot to penetrate the pipe tho.

@edwardmulder3777 2 жыл бұрын

@@duosable I sprayed mine down with some hi trmp engine paint to protect it so should stop water coming in, haven't got it on the bike yet, so don't ask if it works,, but I did prep the pipes and sprayed with anti rust primer and hi temp paint., so they're pretty well protected

@OlderShadowRider Жыл бұрын

@@edwardmulder3777 Did you heat the pipe after coating it to seal it? just wondering also if you wrapped your muffler too?

@edwardmulder3777 Жыл бұрын

@@OlderShadowRider cleaned off rust, neutralized it w Ospho, primers and painted the headers, wrapped them to the muffler, spray painted wrap, heated in oven.

@gregdixon9443 11 ай бұрын

Salt from your sweat turns it white.

@BrickHouseBuilds 11 ай бұрын

Hopefully only a few drops

@TheRealCoozi 11 ай бұрын

I dislike that stuff!

@BrickHouseBuilds 11 ай бұрын

@user-wo2rc3bf4x 12 күн бұрын

Does anyone advise spraying the headers with a high temp silicon spray such as thermo tec (2k degree) then wrap, then spray thermo tec again on the wrap? Is there an advantage or benefit to that method or just wrap it then spray it? Thank you all for any help.