Feel Free to skip ahead or use the control to speed up the slow talking ha ha. Sorry for repeating myself. These videos were linked together so there is repeat information.

A good thing to do after you've drilled your hole is to clear out any remaining cement dust from the inside of your hole. Removing the remaining dust with a shop vac or air hose will assure you the exact depth you need.

You did a great job explaining this build. I may build the same thing. Last time I did a metal building, the corner pieces were pricey. It has been over 5 years but 4 corner pieces 10' long were $50.

Great job! I would run the roof metal panel ridges the other way for shedding snow if your in the snow zone. I’m in the process of reinforcing my portable carport at the 2600 foot elevation and have snow, wind, and falling pine tree limbs to contend with!

Cutting wheel and a grinder will do the job for cutting your metal to size.an i would only put one screw because more holes will just weaken your tubing, a couple of x braces would be good though. You did a great job on your build put mine up with just the canvas topper but when its destroyed i probably ut on some metal.thanks for your time

I like the VW twins. Great ingenuity on the shed. I’m waiting to see what you used to cover the corners and your final rafters.

i just bought one of these 2 days ago. and its nice to know i tin on the side once the canvas wears out. but where i live i can keep the entire 10x17

Nicely done

Thats a good idea with the coupler, i just self tap them together because it was a pain when the came apart.

Temecula allows 100 sq ft. so 8' x 12.5'. For your rafters, take scrap PBR and screw it to each section, if you have extra poles, you can use them as well. Old washer has three sides you can cut up for bracing. Anything with solar electric on top doesn't count towards property tax if you go bigger.

IF you appreciate the information you can use this link to buy ANYTHING on AMAZON. and it will throw some change in the jar toward the channel thanks for watching and tolerating the terrible edit on the video amzn.to/37eheDG

Good idea .... thanks for the video.... very affordable garage ,,,,,,,,,,,,,,,,,,,,,,,

Maybe you mentioned in the video but I didn't catch it, how much did you end up spending for this project aside from the concrete? A cost break-down would be appreciated, thanks

Steel wall studs trimmed to fit walls and roof is how I reinforced mine.

The metal will weigh it down pretty much long as you have some kind of anchors your good I put a joist in I used conduit and just smashed the ends and self tapped it into the metal

How many panels did it take to go up, over and down the other side? Plus the panels for the closed end? Will you add a panel or two to close up the front peak? That would look really good if you don't need the height for what your driving in there. 🇺🇲👍🏻

Awesome 👏 Great Job !

Metalmdimg used facial along roof edge ..or expanding foam to seal the edges of that ... project?

Oh yeah 😎. What size EMT fittings? (EMT=ElectroMetalic Tubing= Conduit as in Electrical Conduit) l.5 inch or 2 inch EMT fittings? Would EMT Compression fittings be stronger/better? FYI EMT "Compression-to-Box" and only Compression-to-Box fittings, the threaded end that goes into your metal box, these threads are same as SAE plumbing threads. Remove the lock ring first, then screw the threaded end of Compression-to-box to the galvanized plumbing fitting of your choice.

This was a great video Mike

What do the corner pieces look like? Are they standard too?

When you're building on a slab, how do you anchor the legs? 🇺🇸👍🏻

Thank you, very helpful. I purchased the 10x10. Did you find a use for the tarp somewhere else? Plan to remove my tarp in future. Thank you again

Why did u cut it

Hello what size emt couplings are those?

Nice

How about some links where we can find these products

Nice job

Very nice!!

If I could buy just the poles, I'd be in business... Lol. I can find the replacement tops but not the poles alone...

What is the rig cap made from ,

You can buy em with the sheet metal, and the frames are a lot stronger.

It does matter what you use to cut the metal them pipe cutters are great because if you use like a grinder which you can and a lot of poeple do or a saw saw and that leaves a rough edge which adventually causes rust unless you seal it with paint where you cut it but that’s a smart choice on your part by choosing the pipe cutter man roofless to you and I did the same thing as you ended up doing it for under 300 but didn’t close the walls in yet I just did the roof and the gable ends I’m doing the back this spring then I’m gonna put a garage door on it with a back man door so I can pull my truck in it and be able to work on my truck out of the elements outside I did mine in regular union corrugated metal got em from Lowe’s for 26$ a piece galvalumed or something does the job for me keep the ran and snow out of the place and off my truck then allows me to work on my truck in the winter without being cold as heck

How it your rig top work. One complete PBV panel

I see you started at the top so you didn’t have to do ridge vents I did ridge vent I have gravel base and just drilled out the holes and used rebar as my anchor just pounded it into the ground and the rebar has a hook on the end so it doesn’t go all the way threw they re did my road when I bought the property and moved my modular home here then they had extra tar roading in a huge pile they were throwing away so I said bring it over here I’ll take it off your hands I just moved here and need something for my driveway they filled my whole driveway for me then I tampered it down and it turned out great

How did you do the roof ridge? Did you just wrap one panel over the peak?

Can you show what you are going to use for the corners? I rains a lot where I live so water tight is important.

If you don’t lay a foundation does it have to be code ?

Cool

I have the 10x17 harbor freight shed and getting ready to place my order for the PBR panels how many panels would be needed?

My Shelter Logic 20x10 garage tent blew over, Imagine the damage if a car was inside

How much did it cost you

17’ to 15’ how did you shorten 2’ feet?

What size emt connector did u use?

What method did you use to cut the panels?

BASED ON MY EXPERIENCE, I WOULD CAUTION ANYONE NOT TO DO THIS. I had a harbor freight carport collapse on my car after a snowstorm. It smashed my windshield and bent the windshield frame….. total damage was $3700. There are other materials to use if you want to make a similar structure. This tubing, in the harbor freight unit, is EXTREMELY THIN. my damage happened two years ago, and in my housing development last year it happened to another resident. In both cases there was damage to the car after a snowstorm. I don’t imagine this harbor freight structure would do any better in Highwinds.

So we're just gonna gloss over the vintage greatness in the driveway?

Great video, how much concrete did it take?

I live in Los Angeles. Is the place you bought your sheet metal near L.A.? Can you let me know where it's located please.. Thank you

you don't have the correct edge distance for the redheads .

Nice Job, how does this compare price wise to just buying one?

I guess asking you if that metal roof would take a foot of snow load wd b a moot point, seeing the lemon trees in the background...

Approximately where do you live? Do you get much snow?

Do you the concern about snow load? I'm guessing you're in California by the fruit trees. No snow worries.

Ever figure out some sort of solution for a door?

Corners need to trim

I'm just curious as to how much this one cost you?

IMHO, it would be cheaper/easier to build a wood built shed from scratch than go this route.

I don’t need to cut posts

What about a door?

Ha i live in hemet

Nice. You do tend to ramble, though.

permanent

I don't see the value in this over a pole barn. This looks like a strong wind will send it to the neighbors. After fixing that you will wish you spent the extra few hundred $s.

2022 update: it now costs 3 times as much to build this. Thanks Biden!

way tooooooo much mumbling............just do it.......................... can't understand half of what you said.....

For 4 and a half minutes you leave the title in the middle of the screen is WHY I "Disliked" your video. Other than you saying cut 6 inches 100 times..