Mercedes W210 Rear Window Regulator Replacement DIY - (E300, E320, E420, E430, and E55 AMG)

Рет қаралды 203,659

11 жыл бұрын

►It's important to check and maintain worn window guides, tracks, and seals. The majority of window regulator failures are a result of a lack of inner door maintenance. You'll find that some basic maintenance goes a long way to help keep your power window system in proper working order.
We're here with Mike from M&M Motors in Clinton, Connecticut to walk you through a window regulator replacement on an E320 Mercedes.
When window regulators are worn and on the verge of failure there are typically warning signs. You will typically hear clicking from inside the door panel when the window regulator is being operated. Alternatively, the motor which powers the pulley system may become weak over time resulting in a slow-moving window in comparison to others. If you are experiencing these types of symptoms it's highly recommended to inspect and replace the worn parts.
Window Regulator Failure Symptoms:
It takes multiple attempts to roll the window up or down
Window speed is slower than usual
Clicking/grinding coming from inside the door as the window is moving up or down
Window out of alignment
The window will not roll up or down (stuck in position)
Mercedes Window Regulator (E300 E320 E420 E430 E55 AMG) - Meyle 2107301546MY
Rear Left: www.fcpeuro.com/products/merc...
Mercedes Window Regulator (E300 E320 E420 E430 E55 AMG) - Meyle 2107301646MY
Rear Right:
www.fcpeuro.com/products/merc...
Mercedes Window Regulator Rivet - Genuine Mercedes 0039902497
www.fcpeuro.com/products/merc...
SUBSCRIBE: kzfaq.info?sub_c...
Fits These Cars:
Mercedes-Benz E300
1996 Mercedes-Benz E300 Window Regulator
1997 Mercedes-Benz E300 Window Regulator
1998 Mercedes-Benz E300 Window Regulator
1999 Mercedes-Benz E300 Window Regulator
Mercedes-Benz E320
1998 Mercedes-Benz E320 Window Regulator
1999 Mercedes-Benz E320 Window Regulator
2000 Mercedes-Benz E320 Window Regulator
2001 Mercedes-Benz E320 Window Regulator
2002 Mercedes-Benz E320 Window Regulator
1996 Mercedes-Benz E320 Window Regulator
1997 Mercedes-Benz E320 Window Regulator
2003 Mercedes-Benz E320 Window Regulator
Mercedes-Benz E420
1997 Mercedes-Benz E420 Window Regulator
Mercedes-Benz E430
2001 Mercedes-Benz E430 Window Regulator
2002 Mercedes-Benz E430 Window Regulator
1998 Mercedes-Benz E430 Window Regulator
1999 Mercedes-Benz E430 Window Regulator
2000 Mercedes-Benz E430 Window Regulator
Mercedes-Benz E55 AMG
1999 Mercedes-Benz E55 AMG Window Regulator
2000 Mercedes-Benz E55 AMG Window Regulator
2001 Mercedes-Benz E55 AMG Window Regulator
2002 Mercedes-Benz E55 AMG Window Regulator
Get free parts from FCP Euro:
www.fcpeuro.com/page/lifetime...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com

Пікірлер: 258

@fcpeuro 4 жыл бұрын

Buy parts used in the video: Mercedes Window Regulator (E300 E320 E420 E430 E55 AMG) - Meyle 2107301546MY Rear Left: www.fcpeuro.com/products/mercedes-window-regulator-e300-e320-e420-e430-e55-amg-2107301546my? Mercedes Window Regulator (E300 E320 E420 E430 E55 AMG) - Meyle 2107301646MY Rear Right: www.fcpeuro.com/products/mercedes-window-regulator-e300-e320-e420-e430-e55-amg-2107301646my? Mercedes Window Regulator Rivet - Genuine Mercedes 0039902497 www.fcpeuro.com/products/mercedes-window-regulator-rivet-0039902497?

@noahmcc1 2 жыл бұрын

what size rivet did you use ?

@encinobalboa Жыл бұрын

Instead of rivets, use M5 .80 x 12 screws with locking nylon washers. Heads are 8 mm hex. Use pair of 1/4 inch ratchets.

@robertkeller6571 7 жыл бұрын

This is the standard that all how-to videos should be based on. Thanks FCP and Mike Omeragic. Clear, concise and the little extra tips so you dont screw anything up during the job.

@fcpeuro 7 жыл бұрын

You're welcome!

@JohnnyEllisEsq 11 жыл бұрын

This is a great step by step video. I would add that on the 2001, there is also a large Phillips screw behind the "ABS" badge.

@carlberget7615 8 жыл бұрын

used this 2 times for both windows. Excellent video and explanation. Forgot to remind that you need to remove the drilled out rivets to stop rattles.

@ILIEV-ISKREN 15 күн бұрын

Thanks for making detailed videos... Yesterday my w210 window regulator broke, rear left with this video I replaced it without any problem 🎉

@nickholz7163 5 жыл бұрын

Great video, helped a lot...however....., for those who have an SRS air bag, there is another screw under the SRS plastic... Because of this vid, I broke the door panel where the SRS plastic is. In the end I manufactured a piece of metal that I glue gunned into the position where the door panel had broken. I think that my fix was even stronger, but I was lucky to have a fitting piece that I could work with. Also, on the inside of the door panel are two pieces that are glued onto the panel. One tore off! I used it as a tool to get the fastener out and then glue gunned it back on. The fasteners for those glued on pieces are smaller than the rest and to get the one that was till stuck in the door out, I needed to run a utility knife under it as I had suctioned itself onto the door. Then lift it out with a pry tool or use the plastic that the fastener goes into as a tool to pull it out. Doing so worked well. Last but not least, to drill the rivets out, I found that an oversized drill bit worked well. When it gets close to the door a rivet ring came off each and every time. Only the tip of the drill made contact at the center when that happened so the door was never touched by the drill. Good luck!

@Tripleedge503 3 жыл бұрын

HIGHLY recommended this video for anyone working on this type of vehicles. Guys a pro at his job

@chrisryder6864 9 жыл бұрын

Excellent video! Thank you for taking the time to do this for us. The window of my E320 just dropped inside the door, did not know what to do. This video has been very helpful.

@fcpeuro 9 жыл бұрын

Chris Ryder Thank you !! --Kyle B

@matttaylor8832 3 жыл бұрын

This was the greatest how to video I have ever watched. I will be ordering my window regulator for my E55 tomorrow morning! Thank you!

@fcpeuro 3 жыл бұрын

Really happy to hear that, Matt! Thank you!

@hunteheavymob4976 3 жыл бұрын

I agree with all of the previous comments. This was the most graphic detail on how to do a job i have seen. Great camera angles. Great instructions. Gives me hope and makes me enthusiastic to do my own that has recently ceased working. Thanks a lot.

@rafaelochoagarcia8427 5 ай бұрын

Hace poco compré el mecanismo y el motor de las puertas de mi carro y me sorprendió que ya no necesitaban remaches los cuales fueron sustituidos por tornillos. Me pareció una mejora con respecto a la versión anterior. Muchas gracias por el video, un contenido que hace más sencillo realizar este trabajo.

@TechnoTinker 8 жыл бұрын

Thank you so much. I used this video a couple of years ago when my rear right window went out on my '99 E320 wagon (one of the pulleys had broken). I ordered a Dorman replacement, and it worked like a charm. I'm using the video again today for the rear left window. This time, it appears that the cable retainer broke (like in the video). Please note that Dorman says the 702-013 "window hardware regulator kit" (separate product than the regulator) will fit my car, but all of the rivets were too big and I didn't want to drill out my holes. I sent it back and used the cheaper rivets that came with my tool.

@tropicalcircus6139 9 ай бұрын

Thanks for the great video. I’ve now replaced two of these in my wife’s car and have come back to the video multiple times.

@ramesjm 7 жыл бұрын

This was an awesome video! Thanks, Mike, for putting this together and including all the details for us to a good job. My 17 year old son and I spent some quality time completing this repair on a newly acquired 97 E320. I have a couple suggestions. The plastic clips that hold the panel in the door should be removed from the door prior to re-assembly. We had a couple of the clip surfaces separate from the door panel. We re-affixed them with a construction adhesive (allowed to dry), then put the clips right into the door panel. So when it came time to put it back on, we just pushed them in the holes, versus having to align and slide them in. If you have a good trick as to how you get them out of the door frame, that would be great!

@Mau105 2 жыл бұрын

This vid is a fantastic and highly detailed, making something relatively difficult doable and simple. 12 minute window regulator change all while explaining the details! I only had to replace window motor, finding this vid invaluable. Another great one is Mercedes Source on how to lube everything to prevent failures. Like this seasoned mechanic found two broken plastic tabs easily fixed with Gorilla Glue and a few clamps. Reassemble directions also really good . Bravo!!

@combatzone11 10 жыл бұрын

Mike,thanks 4 ur video, just finished replacing mine , took me 2 hrs but i got it done. DUDE U R THE MAN! TIP 4 those who are not mechanically inclines, watch the video couple of times.

@skorpsaiyan2361 7 жыл бұрын

Gonna try to attempt this this Saturday, wish me luck! 4 hours of labor estimated, not to bad compared to changing the convertible top. Now THAT's tough, the hardest imo. Trust me, the convertible top is the most outrageous and toughest thing I've ever done. What a pain in the ass that was. 22 hours it took. Why am I ranting lol, just shows you how scarred I am from this. Mercedes wanted $9000 to do the top so that's why I did it myself.

@drstanbackguy 8 жыл бұрын

Thank you for posting this. Just did my left rear, would not have been able to do it myself without this video.

@FisherCatProductions 2 жыл бұрын

Best video out there for this. As mentioned by others, if you have a SRS airbag logo there is a screw under it. And remove all broken junk from bottom of door or you will have noise! Appreciated the tip on how to pop the first clip to begin releasing the top of the panel by the window seal. Many thanks.

@jorgealexander6884 3 жыл бұрын

Such a great how to video! About to change the left passenger regulator on my 99 e320. Thank you!!

@mrbrandonfarr 10 жыл бұрын

I am really impressed with this video! Its completeness and the presentation are just top notch!

@DARKredDOLLAR 3 жыл бұрын

Had my window fall down as I was driving today. Turns out the plastic bit that hugs onto the rail broke. Same thing happened to the left window to previous owner. Thanks for the video. Project for the weekend ;)

@fcpeuro 3 жыл бұрын

Happy to help, Charlie! Hope you got your window working again!

@wb2wly 10 жыл бұрын

Excellent video. I was apprehensive at doing this myself, but you show how easy it is, and the parts are not that expensive. Thanks

@Superman-ni1ww 4 жыл бұрын

Of the few similar video's I have seen, this one is by FAR the most simple and clear!!! I have stripped out the old mechanism and await a new one. I was worried about the handful of screws and where to replace them, and how to replace the door card at the top of the door, but no more. My 2000 W210 E280 very nearly the same design as this. Thanks guys!

@fcpeuro 4 жыл бұрын

You're welcome, Super man! Happy to help!

@Alagor8888 7 жыл бұрын

Thank you for taking the time to make and then posting such a great video. I watched it twice and did the job myself without any issues at all.

@fcpeuro 7 жыл бұрын

You're welcome! Glad it helped you out.

@tonylongX 11 жыл бұрын

Excellent detailed video with both good explanations and camera work. You are now bookmarked for other car issues. Thanks.

@robertschell8410 Жыл бұрын

That was a great video and technician did a good job quickly repairing.

@MrEclay2 5 жыл бұрын

You made this look like a walk in the park! Thanks for the video and wish me luck!

@chrschwarz1 2 жыл бұрын

Great Video - had no problems following the instructions. Everything works just fine! Thanks!

@LasVegasSummer2009 10 жыл бұрын

Hi Mike, Great video, just replaced the regulator on the rear left side. If you visit Vegas I will buy you a beer :) Few notes for first time DIYs: 1) At 6:35 the switch is shown to be pulled. To remove the switch from the door panel, it should be approached from the inside of the panel, and there are 3 clasps that need to be pressed before removal. 2) The rivets I used were 3/16 aluminum. To remove the existing rivets, the drill head I used was 3/16, but 1/4 may have been better. 3) The whole process is easier if you have an electric drill, especially a cordless one. A cordless drill is a good investment and has many different uses. Apparently you can also buy an attachment for a drill that converts it into a rivet gun. Best, JS

@Toffsen2525 Жыл бұрын

Thank you so much. I will probably remove everything and have my mechanic put it back together. I will do the door panel. Thanks

@rickh8137 6 жыл бұрын

Pro job. Excellent explanations and great camera work!

@anitasimko163 9 жыл бұрын

Thank you for your video and detail demonstration very helpful!!

@bryanwalker7031 8 жыл бұрын

Thank you very much for detailing this repair. Now to actually get mine done...

@demarcuss.469 2 жыл бұрын

Great Video! If it I did not have this video I would not have attempted this replacement. I paused and stopped every step of the way. I have SRS Airbags on all my doors, so I disconnected the battery cable to be sure it didn’t deploy. I found the ground cable located near the floor behind my passenger seat and taped it with duct tape, to ensure it didn’t connect to the frame while I worked. Also there is a bolt you will have to unscrew behind the SRS Airbag plastic sign on your door, in order to get the panel off.

@DaGreat81 6 жыл бұрын

Used this video for both rear regulators, good video, another thing is there is an additional screw behind the airbag badge on the door panel for models with airbags in the door

@markhanson8366 6 жыл бұрын

Many thanks Mike! probably about $2000.00 worth of training and experience provided for gratis! Much obliged and hope your biz prospers as a result!

@fcpeuro 6 жыл бұрын

You're welcome Mark!

@driftbustin 8 жыл бұрын

Excellent video, thanks for making this to help me replace my window regulator.

@carlheadley9124 4 ай бұрын

Excellent job explaining every step

@tonydurago9844 4 жыл бұрын

You the MAN, Thank You so Much I really needed this video for my 1998 MBZ E320 Wagon Rear Window.

@fcpeuro 4 жыл бұрын

No Tony, you the MAN! Glad we were able to help, hopefully the install goes smoothly for you.

@vickifox7644 6 жыл бұрын

very nice job. you are a great teacher wish everyone had the ability to do such a great job in explaining things.

@junminjliu 11 жыл бұрын

Thank you very much! In fact, The regulators of both rear side windows of my E320 have been broken 4 times. I really did not use both rear window too often.

@puluke77 3 жыл бұрын

Awesome video, great work

@peterkirk8321 9 жыл бұрын

Great video ! Now I know how to remove the door trim, a bit of a puzzle before with no screws showing. Many thanks.

@marvin00073 2 жыл бұрын

Excellent video! Mine went out on a 2000 yesterday.

@brucelee9941 8 жыл бұрын

You treat your customers cars tender much respect very professional

@ImportedFromSerbia 10 жыл бұрын

Thx Mike. Happened today, regulator failed on rear left door. Using your video i will order the parts and do by myself replacement.

@soucorp 10 ай бұрын

Awesome Video, I have to do this for both rear window regulators.

@itrefresh 3 жыл бұрын

7 years later, thanks to you. very well explained.

@fcpeuro 3 жыл бұрын

Glad even our old videos can still be helpful!

@jestork1 7 жыл бұрын

Good video. Thanks a lot for the information. Nice job. Keep it up.

@dinlehliu2668 9 жыл бұрын

Great video! Thanks for posting it.

@johnnypoz4228 9 жыл бұрын

Great Video!! Thanks for the information Mike....

@bloomergconsulting553 6 жыл бұрын

Thats a Good one .You made it look so easy.

@aftershock2222 6 жыл бұрын

Great vid, the rear regulator just broke on my ‘99 E320. Thanks!!!

@samuelchacko4814 3 жыл бұрын

Excellent video! Thank you....

@andreaslohmar128 9 жыл бұрын

Very nice demonstration!

@masterdetail1455 3 жыл бұрын

congrats man, awesome and simple, neatley explained

@AFIFI112109 7 жыл бұрын

Thanks for your great information! much appreciated!!

@allanisaacs4835 3 жыл бұрын

Just replaced my UK o/s rear. Thank you for you clear and precise tutorial. 5 star.

@fcpeuro 3 жыл бұрын

Glad it helped

@stevesmith5672 6 жыл бұрын

Mike, Thank you SO MUCH for making this video. It was all a mystery to me last year when the window regulator broke on my wife's 2002 E320 wagon, so I had a local independent shop do it. I don't recall the price, but it wasn't cheap! Well, the same regulator went out this week on my 2000 E430. I did some research and (thankfully) yours was the first video I found. Very well done! I got the disassembly done fine, thanks to you, and I am waiting for the new window regulator assembly to come from FCP. I'm not too worried about putting it back together, as I am sure I will watch your video again during that adventure! One thing I will add, I had one more screw holding the door panel on, located under the air bag tab on the door. Also, I would like to warn folks to not let the window go all the way down after you remove the regulator. If it does, it comes out of its front and rear tracks, and can be quite a challenge getting it back in. This actually took me more time to do than the whole disassembly procedure. Mostly because I had to do it two or three times! Since I have to wait a few days for the new part, I fabricated a piece of wood to hold the window in the all-the-way-up position until that time. It was around 21" long. A shorter block would not be a bad idea while swapping parts, just to keep this from happening.

@fcpeuro 6 жыл бұрын

You're welcome Steve! Thank you for the information you provided as well.

@Toffsen2525 Жыл бұрын

Thanks. Might have to brace it up for a while.

@Toffsen2525 Жыл бұрын

Slightly more than 21" so I put a piece from an old bird perch under, several zip ties and it closes and locks.👋

@mikemadore1 2 жыл бұрын

Thank you, excellent video

@thanosd6826 8 жыл бұрын

Your video helped me so much, Thank you

@AFIFI112109 9 жыл бұрын

Thanks for sharing. Nice job!! Continue!

@marioapolinar8465 9 ай бұрын

Good video,thks for your great work

@yevg3876 Жыл бұрын

Thank you FCP Euro for great and very useful institutions , my car is full of FCP parts

@fcpeuro Жыл бұрын

Thank you for the support!

@Samuel-gc6js 2 жыл бұрын

Very good video 👏🏼 Thanks!! :)

@howardgraham4479 4 жыл бұрын

thank you just did mine this afternoon with your video

@ther1rida 9 жыл бұрын

VERY VERY nice instruction!! I will be using this to do mine this weekend. You explained everything nicely

@fcpeuro 9 жыл бұрын

ther1rida thanks! Glad we could help. --Kyle

@philliparmenta4648 4 жыл бұрын

Great video! Used this info to replace regulator on 2001 e320. Thank you.

@fcpeuro 4 жыл бұрын

You're welcome, Phillip! Glad we can help!

@GEV_GHOST 6 жыл бұрын

Thank you my brother awesome video you make.

@lesdunn736 Жыл бұрын

Excellent. Thank you for sharing your skills. 2023.

@Akadectra 3 жыл бұрын

Excellent video. Thank you and greetings from Bavaria/Germany 💖

@fcpeuro 3 жыл бұрын

Thank you very much! Greetings to you!

@jeffhaymond160 4 жыл бұрын

this is a great video thank you

@JulioReyes-lc4dl 4 жыл бұрын

Nice work

@take10creepy74 6 жыл бұрын

We know scary! You made that very un-scary! Thanks, replacing ours this weekend! Left passenger door.

@fdevera 10 жыл бұрын

Awesome Video I am not a handy man but I was able to change out my regulator. Thanks again!

@felm3283 3 жыл бұрын

Great job!!

@chriswalker9435 8 жыл бұрын

Good job very well explained.

@deltaman38730 11 жыл бұрын

That was an excellent video and very plain to understand,,,thanks

@robertdigiovanni3859 6 жыл бұрын

thank you very much, awesome video

@mr.randallinc.8591 2 ай бұрын

awesome stuff! thanks.

@rodneywilliams2863 4 жыл бұрын

Great video, thank you! Had a little problem getting regulator attached to window but got it ! :)

@fcpeuro 4 жыл бұрын

You're welcome, Rodney, glad it was helpful!

@massoudzadeh3394 4 жыл бұрын

Thank you so much. Just had my rear window fixed. Had some problems with the fasteners as they got old and dry and learned how to use pivot gun. I owe you a beer 🍺

@fcpeuro 4 жыл бұрын

Glad we could help Masoud! The preferred beer of choice around here is a New England Style IPA ;P

@massoudzadeh3394 4 жыл бұрын

FCP Euro okay, let me know when you’re coming to California 🍺

@seamusburke 6 жыл бұрын

Great Stuff. Thank You

@veritas3179 3 жыл бұрын

Great video, mine just broke...just ordered from FCP...Thank you!!!

@memeco50 9 ай бұрын

Wow those rivets! Looks like it had been fixed before and they put good quality ones. I'll go to Home Depot to try to borrow one of those sanding thing machines. it looks so easy here!But I'll fix it

@icebergtrails Жыл бұрын

I try to buy all my parts from FCP Euro, but they've been out of stock of these regulators for what seems to be a year. I finally sourced some from AISIN (RPMB029 and RPMB030) and these are excellent alternatives to the Meyle. AISIN is mostly owned by Toyota. Super stout and comes with pre-greased guides. No rivets or rivet gun required. These use supplied bolts and nut. Made in Taiwan, so quality is much better than the no name eBay/Amazon parts. Highly recommend these to anyone looking to do this repair. Good luck!

@Toffsen2525 Жыл бұрын

Thank You!

@elaudio 11 жыл бұрын

Thank you sir.You just saved me 400 bucks.

@loganfowell3482 Жыл бұрын

Beautiful video. Thank you for the help and the part! Now when I have to do the next ones it will take me.half the time. This took me about 1-2 hours 🤦‍♂️

@fcpeuro Жыл бұрын

Nice work!

@chiefppq8084 3 жыл бұрын

Great video and explanation. appreciated sir

@fcpeuro 3 жыл бұрын

You're welcome! Glad you like it!

@tilenjohn23r Жыл бұрын

Amazing, did myself, watch the video twice

@thesecondcomingisnear3538 3 жыл бұрын

Great explanation. 👍

@fcpeuro 3 жыл бұрын

Thanks Ray!

@hardrocking91 2 жыл бұрын

You made it look so easy! Thank you for sharing.

@fcpeuro 2 жыл бұрын

Thanks for watching!

@hardrocking91 2 жыл бұрын

@@fcpeuro I finally did it yesterday. The first one took me 2 hours. The second one took less than an hour. Your instruction was great. Now I have to replace the windshield washer motor on this car!!!

@massoudzadeh3394 4 жыл бұрын

You are a pro man, you are doing this with your eyes closed. Great job. I just don’t have the ribbits 😞 but thanks 🙏

@philipclarke9565 6 жыл бұрын

Great video. Thanks. One thing I would remind some people who might be as distracted and busy as I am, is to be careful ordering a replacement motor online. I ordered one from Auto Zone that the website said "Fits Your Vehicle" and found that the electrical connector was the wrong one. I could have scrutinized the photo and seen the different connectors, but I was in a hurry. A warning that "fits your vehicle" means " fits some configurations of your vehicle" would have been helpful. Being in a hurry can slow you down. Just thought I might save someone from the same fate.

@memeco50 9 ай бұрын

Done! Thank you 😊

@johndegeorge4419 8 жыл бұрын

Excellent video. you made it look very easy. I hope my door is exactly the same. :)

@kalkansemy 2 жыл бұрын

I like you work. Super

@daleuark 7 жыл бұрын

Excellent explicit how-to, thanks for posting. It took about 3 hours for me, first timer. NOTE - our 2001 model (wagon) had a major panel anchor screw under the small SRS tab (side airbag). That little SRS nameplate tab will pull straight out to gain access to the screw - too late for me as I broke the larger plastic housing on mine tugging on the door cover not realizing it was there, but will help someone else to know it's attached if you have the airbags.

@rinko4800 5 жыл бұрын

The reason it has a screw there is because yours is equipped with a door air bag and it needs to hold the door panel snug so the airbag can puncture through.

@Toffsen2525 Жыл бұрын

Not sure if anything broke. Found the screw and there is always gorilla glue.

@encinobalboa Жыл бұрын

I just did front and rear regulator replacement. I used M5 .80 x 12 screws with locking nylon insert nuts. Heads are 8 mm hex. No rivets needed. For front use pair of 1/4 inch ratchets. Attach top screw and nut first, then slide window into regulator guide. For rear, use wrench to hold nut and ratchet to tighten. Window has to be moved up and down to insert bolts. Install drive motor last.

@dontcrushem Жыл бұрын

I've done something similar. I just used whatever sized machine screws and nuts I could find in my leftover hardware bin.

@yeahman349 4 жыл бұрын

Great video! Local mechanic said he couldn't do it and even Halfords auto centre said bring it to a Mercedes dealer lol. Either they are useless mechanics or they couldn't be bothered for the effort on price - the only thing is you have to drill those damn rivets and cut them out - probably why they didn't want to do it as that was the hardest part!

@fcpeuro 4 жыл бұрын

Yeah Man! Sometime you just have to get it done yourself!