DIY Garage Floor Epoxy Coating

Рет қаралды 1,240,865

Жыл бұрын

SUBSCRIBE: bit.ly/2LQB1gi
↓↓↓↓ LINKS BELOW!
Our garage/workshop floor was NASTY! I have always wanted to do an epoxy floor coating in the garage but honestly, it seemed way to hard to pull off. I finally decided to make it happen and I am excited to say that it worked! I saved a TON of money doing it myself and we couldn't be happier with the result. We use this area multiple times a day and every time I step foot on it I am thankful I did it. At the end of it all, it only cost me about $800 compared to nearly the $4,000 it would have cost me to have it done. Below, I have a detailed KZfaq video, all the steps I followed to complete the project and the links to everything I used. I am certain that you can do it!
__________
Details on this project below.👇🏼 For more projects, check out fieldtreasuredesigns.com/blog/
Check out my podcast, The Field Treasure Show! spoti.fi/2CSJgFF
FOLLOW ME on Social Media:
Instagram - / fieldtreasuredesigns
Facebook - / fieldtreasuredesigns
Twitter - / fieldtreasure
Pinterest - / fieldtreasuredesigns
__________
GET PROJECT PLANS HERE: bit.ly/3LFs0nm
(As an Amazon Associate Influencer, I earn from qualifying purchases.)
///// FLOOR COATINGS
Rust-Oleum EpoxyShield Garage Floor Coating (2 Car Kit) Grey: amzn.to/3NEQkYe
Rust-Oleum EpoxyShield Garage Floor Coating (1 Car Kit) Grey: amzn.to/3QaROeA
Rust-Oleum EpoxyShield Clear High Gloss Coating: low.es/3MDK16b
-
///// CONCRETE CLEANING & PREP LINKS
Goof Off Concrete Cleaner & Oil Stain Remover: thd.co/3NDuaps
Zep Citrus Degreaser: amzn.to/3zpMIW1
Drylok Concrete Etch & Cleaner: thd.co/3O43oGG
Quikcrete Quick-setting Concrete Mix: thd.co/3aLhuOF
-
///// TOOL LINKS
Ryobi Pressure Washer: amzn.to/3wUcmiN (Amazon)
Ryobi Pressure Washer: thd.co/3N4D6Ur (Home Depot)
Quickie Outdoor Scrub Brush: amzn.to/39cWCj6
Brush Extension Pole (Don't be cheap as I broke one): amzn.to/3MDZaUO
Drill Attachment Paint/Epoxy Mixer: amzn.to/3MFNalM
Roller Brush Frame: amzn.to/3aDoltv
3/8 Nap Roller Brush: amzn.to/3xBCxw9
Angle Paint Brush: amzn.to/3QeYDfi
Paint Tray: amzn.to/3mvLUqO
Ryobi Blower: amzn.to/3O4fMWZ
Painters Tape: amzn.to/3H6iR6R
Margin Trowel: amzn.to/3O8VsUG
Bosch Random Orbit Sander: amzn.to/3MBg8U6
Mechanix Work Gloves: amzn.to/3NG4Wqz
///// PHOTO, VIDEO & EDITING I USE
Canon 80D: amzn.to/2VHhzab
Canon 10-18mm Wide Lens: amzn.to/2CNa2zh
Canon 50mm Lens: amzn.to/2COnzq8
Canon 18-55mm Lens: amzn.to/2Mepfwo
Rode Video Mic: amzn.to/2VIBR2V
iPhone X: amzn.to/2VrCf64
Tripod: amzn.to/2R9Qq12
iPhone Tripod Mount: amzn.to/2SzTd09
iMac: amzn.to/2VrstAJ
Recording to iPhone: amzn.to/2C0UshJ
Recording to computer: amzn.to/2BWNH0j
----STEPS!
STEP 1 Remove all the stuff on the floor and take low hanging items off the walls.
STEP 2 Pressure Wash the entire floor. Let dry.
STEP 3 Apply stain remover to tough spots or entire surface (I recommend entire surface). Then pressure wash.
STEP 4 Apply degreaser to tough pots or entire surface (again, I recommend entire surface). Then pressure wash.
STEP 5 Apply concrete etching to entire surface. Then pressure wash.
STEP 6 Let dry for 48 hours.
STEP 6.1 Use this time to apply quikrete, great stuff to fill gaps, caulk, and primer/paint to all areas of need.
STEP 6.2 Sand quikrete areas and finalize all paint touchups.
STEP 7 Mix the epoxy base and prepare to paint and spread decorative chips.
STEP 8 Paint the floor. (Have a buddy go behind and spread the decorative chips right away.) Allow to dry 24 hours.
STEP 9 Go across the entire floor with a brush or hand in a work glove to loosen any decorative chips that did not dry flat.
STEP 10 Blow out all the loose decorative chips. (There weren't many.)
STEP 11 Prep the clear coating mix by mixing in the non skid sand. (Highly recommend using some measure of it).
STEP 12 Paint the floor. Allow to dry 24 hours.
STEP 13 ENJOY!
Thanks for watching my DIY Garage Floor Epoxy Coating Video. Video and check out my project plans here: bit.ly/3LFs0nm

Пікірлер: 599

@zooo31 9 ай бұрын

You can always identify a super nice guy by how he responds to critics. Great video and obviously a great guy.

@diywithandrew 9 ай бұрын

Appreciate that, thank you. KZfaq comments can be extremely bad so I try to as positive as I can.

@its-a-bountiful-life Жыл бұрын

Glad I watched, as I am a 61 year old who thinks he's still 30. After watching, I think I am going to have a professional do it. It exhausted me just watching all your hard work. Good job, though.

@diywithandrew Жыл бұрын

I’m glad it was able to help in that way. Sometimes that is just the way to go - pay to have it done. Thanks for taking time to comment and I hope your floor turns out great.

@cowslinger64 Жыл бұрын

Excellent, well thought out plan and execution. I've thought many times of doing this myself. I appreciate you sharing your experience. Thanks!

@diywithandrew Жыл бұрын

Thanks for the kind comment and I wish you the best on your project if you do it!

@mimiallen225 Жыл бұрын

Hi , new subbie here!!!! Words cannot express how grateful I am for finding your channel!!! My husband and I recently purchased our home and our garage needed a touch up, badly! Well, with your step by step instructions WE DID IT!!! Our first DIY…EVER!! THANK YOU SO MUCH!!!!

@diywithandrew Жыл бұрын

Hi there. Thank you for taking time to share a really nice comment. I’m so glad to hear that my video helped! Great job on taking the chance to do a project yourself! I’m glad it turned out good.

@PreciousOlocha 11 ай бұрын

I have a salon and the prices these floor ppl are calling out is giving me a headache so I’m going to try this. I’m so excited 😆

@mimiallen225 11 ай бұрын

@@PreciousOlocha Please do it!!!!! It was not difficult at all. Exactly, when we were quoted thousands of dollars, this frugal woman said oh no, I’ll do it myself 🤣🤣😂😂

@user-xq9lw2sv3t 4 ай бұрын

Ain't gonna last. No grinding? Lol. Don't listen to this clown. Definitely a failed floor in the near future.

@8437lds 9 ай бұрын

Thanks for the all the details, especially tools and items that you used for this project.

@diywithandrew 9 ай бұрын

You bet! Thanks for watching and the cool comment.

@brockwrichards 8 ай бұрын

One of the greatest videos on the subject. Will mirror most people's experience. Thanks!!!

@diywithandrew 8 ай бұрын

Thanks for watching and the kind words. Really appreciate that!

@user-xq9lw2sv3t 4 ай бұрын

No grinding, and greatest video? Lol.

@dehavinwatie8985 11 ай бұрын

Boss, I am getting ready to do my floor, n I wanted to compliment you on your video, you explained how to do this perfectly, GREAT and in great detail. Thank you again, n your wife was a great help.

@diywithandrew 11 ай бұрын

Thank you for watching and taking time to share a nice comment. I really appreciate that and good luck on your project as well!

@TheBarnCarsandBicycles 8 ай бұрын

Great video. Well done. You did a great job showing all the important details and also what you might have done different if a next time. Thanks for taking the time to show us.

@diywithandrew 8 ай бұрын

Thanks for taking time to watch and to write a nice comment. I really appreciate that!

@EarlBalentine 9 ай бұрын

Nice job, it's one of those projects that you really feel good about when it's done.

@diywithandrew 9 ай бұрын

Thank you! Totally agree! Very glad I took the time to do it.

@KiaPresley 9 ай бұрын

Awesome. I was so intimidated by the process. But, you made this tangible for me. thank you and the wife for this.

@diywithandrew 9 ай бұрын

Thanks for watching and let me know! Honestly I was mega intimidated by it as well but we just took it step by step and it turned out great. Best of luck to you on your project. If you end up doing it send me finished pics in instagram! @fieldtreasuredesigns

@jamesg5001 Жыл бұрын

one of the best videos I have seen on this project. thx for posting!

@diywithandrew Жыл бұрын

Really glad to hear it. Thanks for letting me know and for watching. Really appreciate it.

@vioricagherman9216 4 ай бұрын

Wow you are a perfectionist. I enjoyed watching your work. Thank you for sharing!!!

@diywithandrew 4 ай бұрын

Haha! That is so true. Thanks for taking time to watch and comment

@michaelromero1210 Жыл бұрын

Very nice! Nice attention to detail (edges)! I’m waiting for it to warm up to do my patio

@diywithandrew Жыл бұрын

Thanks! Appreciate you taking time to post a positive comment. Awesome about your patio! I hope it turns out great.

@timc8913 Жыл бұрын

Thanks for sharing your experiences and process. I've had this product in the closet for 6 months and haven't brought myself to apply it yet. You gave some great tips & ideas. I know feel prepared to give it a try.

@diywithandrew Жыл бұрын

Thanks for taking the time to comment Tim. I understand having material ready for a project and not feeling ready to tackle it. I hope your project turns out great! Send me a picture of the finished result!

@doloresturnwall3200 2 ай бұрын

Great video, very helpful. Feel like I can tackle it myself. Love your organized garage ….. nothing out of place.

@diywithandrew 2 ай бұрын

Thank you very much!

@hangphuchienhien9078 7 ай бұрын

Great Job Brother Ur Wife is a great helper too brother you guys doing so amazing floors

@diywithandrew 7 ай бұрын

Thank you!

@michaelhiggins2562 7 ай бұрын

Thank you, getting ready for similar project!

@diywithandrew 7 ай бұрын

Awesome! Let me know how it goes.

@brad1953 2 ай бұрын

Great job on the garage floor. Looks amazing!

@diywithandrew 2 ай бұрын

Thank you! I appreciate that

@premsun Жыл бұрын

This one heck of a video and a heck of a project ! It definitely inspired me to get the ball rolling this summer ! Thank you so much!

@diywithandrew Жыл бұрын

Man thanks so much for your awesome comment. Pumped it helped you! Thanks and good luck on your project!

@evelynpoole2977 Жыл бұрын

Can you just add the poxy over your already painted floor? Just asking e

@spartanepoxies3798 8 ай бұрын

Hey man, pretty good job. For the etching process, the concrete should have been sprayed down first, and you should have used a watering can for the etch. I didn't catch the etch you used, but please make sure that you don't need to neutralize the concrete after etching as some of the muriatic acid etch products out there still require the acid to be neutralized with a baking soda / water wash down. For spalling, cracks, and imperfections you can use a 2 part - 100% epoxy filler. It's just going to adhere better is all. If you have expansion joints, consider using a fast-set polyurea. Spartan Epoxies offers a tubeset called JS100. For the flakes, I would do whats called a full flake broadcast. Essentially gives you an entire layer of paint chips for superior durability and drop protection. If you do a full flake broadcast, then 2 coats of urethane topcoat is needed. 1 coat for whats called the grout coat, and a final urethane topcoat as your finishing coat. You should have used a 120 grit screen (drywall screen) to hit the flakes the day after application, and not gloves. For the application, because you used a epoxy paint, and not a true epoxy, I suppose you may have had to apply that way. However, I would have poured the epoxy across the back wall, then used a flat squeegee to spread, then wore what's called gunite spikes. Which enable you to walk thru the wet epoxy. Then you can go on the floor and backroll using a high quality phenolic core roller cover, double weaved nap of course. Once you back roll you can broadcast your flakes, and since you have spikes you can walk around to broadcast them. We broadcast up in the air, typically using the term feeding the chickens as this is exactly what it looks like. This technique helps to ensure an even look. I think you did good for what you were doing there and thanks for helping the industry. It's important that people understand how important it is to apply a coating over their garage floor. These days you can apply all sorts of really awesome types of epoxy. Great job man. I hope this is received well and I promise I'm not trying to be negative. Just trying to help anyone here.

@diywithandrew 8 ай бұрын

Dude, thanks for being so constructive and helpful in your comments. And thank for watching my video. You are one that I wish I could have learned from before I started my project. I appreciate you taking time to add to the knowledge base here and helping my viewers in such a positive and informative way. Thanks again and I hope many benefit from it!

@josuemaganajd5428 7 ай бұрын

Very good information here! I’ll definitely save your recommendations when I’m ready to do my garage, hope you can make a video as well to show us how is done!

@spartanepoxies3798 7 ай бұрын

@@diywithandrew No problem at all. Sometimes just jumping in and doing is the best way to learn. You can try to plan, and plot but at the end of the day when you get the experience and actually do a floor you learn so much as you know. Good luck man and great job again.

@randomsucks2444 9 ай бұрын

Thank you, I was just about to do my garage floor and was unsure about how much I would need. Didn't think about fixing the small pot marks in the floor.

@diywithandrew 9 ай бұрын

Thanks for watching and letting me know! Hope your floor turns out great.

@carlosmontilla4369 10 ай бұрын

I am working on my garage and contemplating whether to apply epoxy. I appreciate your willingness to share your experience; it provides valuable assistance. Thank you.

@diywithandrew 10 ай бұрын

I'm glad to hear that my video helped. Thank you for taking time to watch and let me know! I wish you the best on your project!

@carlosmontilla4369 9 ай бұрын

@@diywithandrew My project got perfect, thanks to your guidance. I am not sure I can post a picture here; that'd be awesome.

@edisonbuhay1349 9 ай бұрын

Great video thank you for making everything clear! Just a question; how long did every step take to dry?

@diywithandrew 9 ай бұрын

Thanks for watching and the comment. I tried to wait at least 24hrs between coats and I think I waited 48 before doing the clear coat. Hope that helps!

@newtonslaw7296 10 ай бұрын

Good job mate, done well! Thanks for sharing those learning opportunities.

@diywithandrew 10 ай бұрын

Thanks for taking time to watch and to write a comment. You are what makes KZfaq great!

@WorkingTimbersCo Жыл бұрын

Nice job man! Thanks for the tips! On my list!

@diywithandrew Жыл бұрын

Thanks man! Really appreciate the comment. Good addition to the list! I think you will be glad you did it!

@binyammamo6454 Жыл бұрын

You did a good job man, and I learn from it! Thank you!

@diywithandrew Жыл бұрын

Thanks!

@Smithb83 Жыл бұрын

Looks great, good tips too. Here's my tip - use a 15 litre paint scuttle instead of roller trays (with disposable liners) 👍🏻

@diywithandrew Жыл бұрын

Thanks! And great tip. Appreciate you sharing.

@donnacrozier2003 2 ай бұрын

WOW, l have to do my garage floor! Thanks for sharing & uploading. Nice!

@diywithandrew 2 ай бұрын

Awesome! Glad to hear it!

@ericbillies1569 8 ай бұрын

This was a great DIY video, exceptionally helpful!!! Pretty much followed Andrew’s process (and incorporated some insightful comments - e.g., using 18” roller). Some other lessons learned: 1. New Rustoleum package has the dual pouches - makes it easier to mix together. 2. Epoxy is thick - roller was a little tricky and sometimes was splotchy, sometimes hard to get a consistent coat. 3. After the epoxy dried, had some dark spot discoloration in a few areas. Not sure why, not a major issue but only negative thing (note, it is not from the concrete). 4. Absolutely need 2 clear coat packages for a 2.5 car garage. It was was very hard to see where you may have missed (as he says) and missed a couple of areas after it dried. So I sucked it up and bought another one to complete the job. Thank you again, Andrew!

@diywithandrew 8 ай бұрын

Wow, Eric! So glad to hear that my video helped and that you got more help from comments. Thanks for sharing and adding to the knowledge here!

@nadovidaich2364 Жыл бұрын

Great job! Thanks for sharing. Can’t wait to do mine …………. 👍🏻

@diywithandrew Жыл бұрын

Thanks! Hope yours turns out great.

@aishalovelyme6229 9 ай бұрын

Omg!! Great job 👏🏾 🎉 I’m impressed! The before and after is amazing. This gives me hope for my first home project on my floors 😁 Thanks for sharing. And ignore the trolls.

@diywithandrew 9 ай бұрын

Thanks for watching and the kind words. I wish you the best on your project.

@briandevillier9850 Жыл бұрын

I enjoyed your video. My wife and I are having a company do ours. It's 6.50 a square. It's looking good. I hope all of ours last a long time. We surely enjoyed your video.

@diywithandrew Жыл бұрын

Thanks for taking time to write a nice comment. I hope yours turns out great and you get many years of enjoyment out of it. We are coming up on a year with ours and it still looks like I just did it and am so glad I did. Take care!

@Isaac-px6vl 8 ай бұрын

Thanks for the video. I don’t see the link you have mentioned to use for tool required for the job.

@diywithandrew 7 ай бұрын

You bet! Here are all the links: (they are in the show notes if you scroll down but I'm pasting them here as well) ///// FLOOR COATINGS Rust-Oleum EpoxyShield Garage Floor Coating (2 Car Kit) Grey: amzn.to/3NEQkYe Rust-Oleum EpoxyShield Garage Floor Coating (1 Car Kit) Grey: amzn.to/3QaROeA Rust-Oleum EpoxyShield Clear High Gloss Coating: low.es/3MDK16b - ///// CONCRETE CLEANING & PREP LINKS Goof Off Concrete Cleaner & Oil Stain Remover: thd.co/3NDuaps Zep Citrus Degreaser: amzn.to/3zpMIW1 Drylok Concrete Etch & Cleaner: thd.co/3O43oGG Quikcrete Quick-setting Concrete Mix: thd.co/3aLhuOF - ///// TOOL LINKS Ryobi Pressure Washer: amzn.to/3wUcmiN (Amazon) Ryobi Pressure Washer: thd.co/3N4D6Ur (Home Depot) Quickie Outdoor Scrub Brush: amzn.to/39cWCj6 Brush Extension Pole (Don't be cheap as I broke one): amzn.to/3MDZaUO Drill Attachment Paint/Epoxy Mixer: amzn.to/3MFNalM Roller Brush Frame: amzn.to/3aDoltv 3/8 Nap Roller Brush: amzn.to/3xBCxw9 Angle Paint Brush: amzn.to/3QeYDfi Paint Tray: amzn.to/3mvLUqO Ryobi Blower: amzn.to/3O4fMWZ Painters Tape: amzn.to/3H6iR6R Margin Trowel: amzn.to/3O8VsUG Bosch Random Orbit Sander: amzn.to/3MBg8U6 Mechanix Work Gloves: amzn.to/3NG4Wqz

@brentowen9480 Жыл бұрын

Been cleaning my automotive shop's floors for year and honestly I think Dawn Soap, water, scrub broom, rinse and squeegee are the best floor cleaners.

@diywithandrew Жыл бұрын

Thanks for sharing

@ingridahmed5156 6 ай бұрын

Congratulations looks great. I wish I could epoxy my garage but it's too much work cleaning it a patching it up. Your garage looks bigger great job for both of you. Now you can enjoy it.👍👍

@diywithandrew 5 ай бұрын

Thanks. I appreciate you watching and taking time to comment.

@giovanadandolini9383 8 ай бұрын

Great. I’ll do it on my garage floor. Where did you buy the stuffs? Thanks.

@diywithandrew 8 ай бұрын

Awesome! If you check the notes below the video and click "more", you will see all my notes with links to what I purchased as well as the steps. Hope that helps!

@phillipmcgrath599 Жыл бұрын

Awesome Thank you going to do mine as well, How soon did you apply the clear coat on the epoxy ?

@diywithandrew Жыл бұрын

Awesome! I waited 24hrs before the clear coat application. We live in a dry climate so if not dry I’d maybe wait 48hrs.

@shawntruongorigami7558 12 сағат бұрын

appreicated, I just did it and follow your guide , great video 👍🏼

@diywithandrew 10 сағат бұрын

Right on! Thanks for watching.

@Speak-Fearlessly 8 ай бұрын

Did you have any wood in the floor to go over? Like against the wall or anywhere for expansion absorption? If so, any thoughts on epoxying over it?

@diywithandrew 8 ай бұрын

I didn't have any wood. I have no idea how that would react. Sorry I am not more helpful there. Maybe the comments might have some advice?

@davidcannon5104 11 ай бұрын

This is so much work and I applaud you/anyone who’s successfully completed this!! However, I am leaning toward patching/repairing the concrete cracks and buying a giant floor mat instead. I have two small boys and just don’t think I’ll have the uninterrupted time to do this right way and I don’t have the extra money to pay a professional.

@diywithandrew 11 ай бұрын

Thanks for the kind words and yea I totally get that. Sometimes you have to pick the right solution to meet your time and money.

@shailajakarri5088 Жыл бұрын

Detailed presentation ! very Beautifull !

@diywithandrew Жыл бұрын

Thanks for watching and for taking time to write a nice comment.

@amosfeldman9454 Жыл бұрын

Great video. Looks great. I'm sure I have more thoughts on this but first impression - awesome video. Better than the videos these companies put out for their own products.

@diywithandrew Жыл бұрын

Thank you, Amos! I appreciate you taking time to let me know.

@RealBeautyRealFoodandRealLife 9 ай бұрын

thanks for sharing, can I just have the paint center mix or I have to manually do them ? sj

@diywithandrew 9 ай бұрын

Thanks for watching! That’s a good question. I’m sure if you take them in and ask that they would mix for you.

@jimdickie7038 20 күн бұрын

Great, informative video. You kept it real, the good and the bad. After getting some quotes, you may have given me just the push I needed.

@diywithandrew 19 күн бұрын

Thank you for the comment and for watching! I hope your project goes well!

@shankarrao2572 7 ай бұрын

Great video. With lots of tips/ideas. But here is a question. From what I have seen . .there are 2 types of Epoxy kits. One is water based. And the other is solvent or oil based. Is any one better than the other? Not only in terms of looks/final finish .. but also in terms of applying (the effort or difficultiness) of the epoxy itself? Please advise

@diywithandrew 7 ай бұрын

Thanks so much for watching and commenting. Honestly, I don't know. All I can speak to is what I used. See the links below my video in the show notes for the exact product I used. I also just launched a video reviewing the floor after 15 months of use if you want to check it out! It launches tomorrow. kzfaq.info/get/bejne/Z7ifqKmVmsmYiYk.html

@najibahmadi4041 2 ай бұрын

Great job, Richard

@diywithandrew 2 ай бұрын

Thx!

@FredMcIntyre Жыл бұрын

Great job, it looks awesome! 😃👍🏻👊🏻

@diywithandrew Жыл бұрын

Thanks, Fred! I appreciate you watching and taking time to write a positive comment.

@Angel-ld9gz 8 ай бұрын

I am going to give it a shot , question was it your first time? Thanks for the video

@diywithandrew 8 ай бұрын

Awesome! I hope it goes well. Yes it was my very first shot at it. Thanks for watching.

@BlackBirdieGolf 8 ай бұрын

What do you suggest for a more less slippery flooring. I did the epoxy about 10 years ago and dropped my motorcycle because the floor is slippery.

@diywithandrew 8 ай бұрын

You definitely want to mix the sand in with the final clear coat. I mixed in all of it and I think that helps a lot.

@90ERS Жыл бұрын

That was a nice video. I did my 2.5 car garage 10 years ago with the same Rustoleum product, in a very similar way, and it turned out great and has lasted forever. Looks today like it did when I installed it. Here are a few additional tips to consider, and a few commenters probably already mentioned these. Use a wider roller, I used a 12” or 15”, can’t remember which (but not a 9”). Use a disposable liner in your roller pan with a piece of cardboard underneath to catch drips. I painted the entire perimeter all at once, taped off along the walls, and quickly. Then you can roll the surface quickly as well with the larger roller. Not important if the edges start to dry and won’t hold the color flecks. The prep is absolutely the most important step in all of this. Filling the cracks and holes, I used an epoxy based concrete filler and then sanded smooth with an angle grinder. An orbital sander with the right grit is also great for this. Degreasing and cleaning is critical, but the most important is getting a good acid etch. What they give you in the kit is useless. I used muriatic acid (pool chemical), which is 31.45% (20 degree Baume) HCl (hydrochloride acid) that was available at the big box stores. It’s cheap too. Note: you HAVE TO USE EYE AND SKIN PROTECTION and be very careful with this stuff, but if you follow the precautions, use appropriate PPE, you will safely achieve a far superior acid etch in only one application. I diluted the acid with 2 parts water to 1 part acid, always pour the acid into the water (and never vice versa). Make sure you have good ventilation too. It makes for a really deep etch. Then you have to rinse really well due to the amount of fine solids removed by the etching. Pressure washer is great for this. A wet/dry vac also helpful. Of course if you have a diamond grit floor sander instead, that would be wonderful and less hazardous. 😊 I have another floor job coming up soon for a 3 car in our new house. Can’t wait!

@diywithandrew Жыл бұрын

Eric, thanks for your kind comment and for all of this great advice for our viewers. I think many will benefit from your wisdom and experience.

@thesofspades8709 Жыл бұрын

Hello. Should I do an acid etch or use a sander, or do I have to use both?Thanks In advance.

@90ERS Жыл бұрын

To s of spades, by all means use a floor sander with a diamond grit pad, if you have one. That is how professional installers do it, for a variety of reasons, one being the floor stays dry and they can put on the first coat immediately after vacuuming off the dust. The acid etch works just as well if you don’t have the floor sander, but the disadvantages are apparent.

@diywithandrew Жыл бұрын

@@90ERS Thanks for contributing, Eric! Appreciate you taking time to help educate our viewers.

@moxl1234 10 ай бұрын

My pro used the epoxy filler after the initial sanding for rough areas and cracks, then sanded it after it was dried overnight. Then applied the first epoxy coat. That gets rid of the rough imperfections you had in your floor.

@matthewlewis8605 Жыл бұрын

Great video! Always good content P.S. long live the Newcastle sign!

@diywithandrew Жыл бұрын

Thanks my brother. Haha! She’s still hangin with me.

@doctordiv 8 ай бұрын

You sound like Rener Gracie! Thanks for the awesome video!

@diywithandrew 8 ай бұрын

Haha! I wish I was good at Jiu Jitsu.

@DanCampbell-zb2gd 4 күн бұрын

Great video. Very informative. About to start my project and have the kit and all the materials. What clear epoxy did you use?

@diywithandrew 4 күн бұрын

Thanks! Here’s exactly what I used on Amazon. (I get a small commission if you use my link): amzn.to/3UWUAbW

@troubletyme5561 Жыл бұрын

I bet it was a nice rewarding feeling after finishing! I’m going to do the same thing! Thanks for this knowledge, great reference video bud!

@diywithandrew Жыл бұрын

It definitely was and still is. Thanks for the comment and I hope yours turns out great.

@AcapellaVideo 7 ай бұрын

Thanks for this great video! It helped me get the right materials for my garage. Also, as an Argentinian myself, I just noticed you using the Argentine AFA shorts haha. You should be updating with the 3 stars now lol.

@diywithandrew 7 ай бұрын

Thanks for watching and the nice comment! I am so glad you noticed the shorts! I have been to Argentina 5 times and have MANY dear friends there. Yes. I need new shorts with 3 stars! Viva Argentina! I also just launched a video reviewing the floor after 15 months of use if you want to check it out! It launches tomorrow. kzfaq.info/get/bejne/Z7ifqKmVmsmYiYk.html

@nanakadidiasoumano Жыл бұрын

Great video. I’m following your video to do my garage. But totally off topic, where did you purchase the shoe rack? Or was it a diy shoe rack?

@diywithandrew Жыл бұрын

Thanks! Oh man the shoe rack is awesome. Amazon. I actually just added a second we like it so much. Here’s the link: amzn.to/3WjuvSP

@kristenwilliamson8455 17 күн бұрын

Looks fantastic!

@diywithandrew 17 күн бұрын

Thanks!

@soutkorbaag3713 4 ай бұрын

Great job, well done 👍🏽

@diywithandrew 4 ай бұрын

Thank you!!

@randyfrantz7195 Жыл бұрын

Thank you for the video. I was considering doing an epoxy floor for my garages. Not any more. I'll just clean the concrete and forget it. Plus, I have heard that the epoxy will chip. That could be from improper prep work. You won't likely have that happen. Thanks again!

@diywithandrew Жыл бұрын

Glad it helped you come to a decision. Thanks for watching and the comment.

@sausauia9799 11 ай бұрын

Thanks for the video, very helpful.

@diywithandrew 11 ай бұрын

Thanks for watching and the nice comment!

@samadhistate9637 Жыл бұрын

Nice work. No acid etching or diamond buffing in your prep? This greatly helps the epoxy to bind.

@diywithandrew Жыл бұрын

Thanks. I did etching. Twice actually. It’s been a year and holding up great!

@stefanarchuticz6168 Жыл бұрын

Great video. I'm a professional installer and one thing that's not discussed enough with epoxy coatings is the fact they are not UV stable. You can expect yellowing in areas that receive consistent exposure to natural light. Polyaspartic is the best coating material for a garage floor, but unfortunately it's not a DIY product due to its very short pot life.

@diywithandrew Жыл бұрын

Stefan, I’m honored you would take the time to watch and comment. You are absolutely right in that I didn’t mention anything about UV rays (didn’t even think about that fact) and didn’t learn that detail until about 3 weeks after filming and seeing the effect of the UV rays from the sun. After about a month I noticed yellowing on about 10” of area from driveway to garage floor where I applied the coating “outside” the garage doors where they rest on the concrete. There is now a yellowish strip along that section when viewed from outside. Obviously, had I known that would happen, I would have shared that in my video. It’s not the worst thing to have happened but it certainly doesn’t look great. Haha. Also good to know about polyaspartic. I will say that after almost a year, it is performed really well and I’m glad I did it. Thanks again for stopping by and sharing your knowledge with our community here.

@commoncents456 Жыл бұрын

Thank you for your input.

@johnfeather5405 Жыл бұрын

Hey Stefan where can a dIYer get polyaspartic? What about Sherwin Williams?

@totalgaragesolutionsllc6043 Жыл бұрын

@@johnfeather5405 there are several online stores that sell it, but not SW. Just be prepared, it’s quite expensive. It will generally cost between $1-$1.5/sqft just for the Polyaspartic.

@hello-nq3ze Жыл бұрын

@@totalgaragesolutionsllc6043 roughly $500-800 for the entire garage, definitely worth it though. Would it be weird to coat like 75% of it in regular epoxy then the exposed portions with polyaspartic or is the consistency just too different?

@user-wy1tn9hq8m Ай бұрын

Thanks a lot to help Definitely do after couple of days Thanks again Really appreciate!

@diywithandrew Ай бұрын

Awesome. Glad to hear it!

@Tigerrag89 11 ай бұрын

Got my sub with the Clemson hoodie! Clemson native here! Also, great video! Thanks for the info!

@diywithandrew 11 ай бұрын

Haha! That’s awesome dude! Thanks and for joining. Welcome aboard!

@alexanderaw1146 8 ай бұрын

How long did you let the epoxy dry before applying the clear coat

@diywithandrew 8 ай бұрын

I think it was 48hrs

@geo100x 8 ай бұрын

I would apply one coat of paint without the chips first, on the second coat with chips. Good job. 👏👏👏

@diywithandrew 8 ай бұрын

That’s a great idea. And thanks for watching and the nice comment

@ryant2736 7 ай бұрын

Thanks so much for this video! I am excited to embark on this project. One question - when you were applying Etch and Cleaner and you said you did it in sections, did you wash off each section before moving on to the next? For example, did you etch, scrub, wash, etch, scrub, wash, etc.? I ask because it seems like that would get the surrounding areas wet which I can't imagine is ideal. Any tips? Thanks!

@diywithandrew 7 ай бұрын

Thanks for watching and your kind words! Yes great question. I applied etching and cleaner in sections but I performed the rinse all at one time when I was done scrubbing each section. Hope that helps!

@jellybeanvinkler4878 9 ай бұрын

Very helpful Thanks!😊

@diywithandrew 9 ай бұрын

Glad it was helpful!

@simflightpro 9 ай бұрын

Nice job and thanks for the video!

@diywithandrew 9 ай бұрын

Thanks for watching and the comment! 🙏🏼

@daleandlauriecook 10 ай бұрын

Than you for this video! We are going to do our garage ourselves.

@diywithandrew 10 ай бұрын

Thanks for watching and the nice comment. I hope you’re project is a success and you can enjoy it for many years. We are so glad we did it and even more than a year later it’s still awesome!

@nicholasholmes7837 Жыл бұрын

Good job dude looks good!!!!!

@diywithandrew Жыл бұрын

Thanks!

@richf9608 9 ай бұрын

How long did you let the epoxy and clear coat dry before putting your stuff back in

@diywithandrew 9 ай бұрын

I think I waited 48hrs to be safe!

@Speak-Fearlessly 8 ай бұрын

We’re there any oil spots that didn’t lift completely when degreasing? I have a few that I’ve scrubbed 4x and there is still water pulling off these spots, even after etching. Do I hit it again?

@diywithandrew 8 ай бұрын

Yes absolutely. That's what I was worried about and why I did so many cleaning passes. However after a point I just went for it and I can say after a year and a half I haven't seen any issues with anything coming back up through. The only areas where there is any issues is the small areas up front where the sun hits the clear coat. It yellowed a little but thats IT. Hope that helps!

@marialokuan 7 ай бұрын

I did my garage today and I would like to know when can I apply the sealer? Thank you

@diywithandrew 7 ай бұрын

I am pretty sure I waited 48hrs. Hope yours turns out awesome!

@chert023 Жыл бұрын

Any tips on maintenance on these floors? Or anything to get stains off the epoxy? Or should you add more clear coat after a year or 2?

@diywithandrew Жыл бұрын

After almost a year we have had no problems with the floor. We clean it with a rag and a little cleaning solution in water in spots that have gotten a little dirty. So far that’s all it’s needed. Depending on the wear I assume another clear coat (after cleaning and drying) probably wouldn’t be bad. But that’s about the extent of my knowledge. Maybe another viewer can comment if they have more knowledge. Hope that helps.

@MrJohnnyboyrebel Жыл бұрын

The previous owner of my house put epoxy floors in both two-car garages. We keep our cars in one, and the other is my workshop. I am considering grinding them both out, 1) the floors are very slippery when wet, like rain dripping from cars kind of wet, 2) the flakes make finding dropped items like screws, nuts, nails, etc. nearly impossible to find. I use a flashlight lying on the floor to create a shadow. These are the two reasons I would discourage epoxy floors, especially in a workshop.

@diywithandrew Жыл бұрын

Those are great thoughts from your experience. Unfortunately the previous owner must not have our down the clear coat with the sand mix which reduces the slip factor. You are right on the hard to find small items issue. I’ve had some long hunting sessions! Ha! The flashlight is a great idea.

@christopherterry5457 Жыл бұрын

There is no slip factor if done correctly. As for you dropping items and not finding them - How about using a magnet or broom/vac/. You wouldn’t catch me on the floor looking horizontal anymore with my bad knees. Have you tried being more careful not to drop things? Just say’in.

@PursueTheUnknown 8 ай бұрын

Can you skip the flakes step? Step dad had epoxy floors with flakes and it was maddening finding dropped items. Want to do epoxy in new house, white epoxy floors but not use the flakes.

@jaigopaul8772 Жыл бұрын

Very nice, looks great 👍 👌

@diywithandrew Жыл бұрын

Thanks!

@MrMongoblue 7 ай бұрын

I'm curious as I'm about to embark on this journey myself. A year later now how has it held up?

@diywithandrew 7 ай бұрын

I just launched a video reviewing the floor after 15 months of use if you want to check it out! It launches tomorrow. kzfaq.info/get/bejne/Z7ifqKmVmsmYiYk.html

@friedgigabacon 11 ай бұрын

“Thank you Andrew aka myself…” that was funny 😂… cool video man!

@diywithandrew 11 ай бұрын

Haha! Thanks man!

@jaxchristian3080 9 ай бұрын

Looks good

@diywithandrew 9 ай бұрын

Thank you!

@tomlapham5532 5 ай бұрын

I have to say great job on all of the prep!! I work in a paint store and my boss doesn't even like selling either the Rustoleum garage floor kits or the professional two part, expensive paints even to professional painters because too many people cut corners on the extensive prep work necessary. You MUST emulsify, dissolve, clean all oil stains. Some even require etching with muriatic acid especially glossy concrete or the material will not stick. Another test often overlooked is for moisture and water coming up through the floor. You need to take say a 3ftx3ft piece of plastic and tape it to the floor securely overnight. If you come out the next day and there is moisture under the plastic you could run into problems with peeling. We try and talk people out of doing this themselves, even professional painters unless they listen and do all of the prep. Love to hear form you about how the floor is a year or so later. Even with all of the prep in the world, if you park a car on the floor hot tires will peel the paint. Looks like this garage is your shop so that's not a concern for you but with the next owner it could be.

@diywithandrew 5 ай бұрын

Getting praise from someone with your knowledge and experience is a big deal. I don't take it lightly. Thank you! Also thanks for taking the time to watch and comment so others can learn. Obviously this is a DIY approach and I don't claim to be a professional. Overall I am happy with the job I did. I think there are a lot of "professionals" that still do a bad job. After a year and a half, I have had no problems with pealing, but I see peeling ALL THE TIME in houses because I am a real estate agent and I see a lot of homes and garages. Thanks again for stopping by. Here is the link to my update video if you are interested: kzfaq.info/get/bejne/Z7ifqKmVmsmYiYk.htmlsi=3cKXJzH7fGMCTPP7

@neillbazalar9651 8 ай бұрын

great job

@diywithandrew 8 ай бұрын

Thanks!

@rickmucci4785 10 ай бұрын

Super Nice and friendly video, well explained step by step DIYer, what not to forget and even sharing your mistakes. Thank you, liked and subsc

@diywithandrew 10 ай бұрын

Wow thanks for the kind comment. I really appreciate that and thanks for watching. Welcome aboard!

@rickmucci4785 10 ай бұрын

@@diywithandrew 👍😀

@parveenkhattra9348 9 ай бұрын

Hey how many days did the process take?

@diywithandrew 9 ай бұрын

I think it took us about a week when we include prep, applications and dry times.

@PnoyWonderBoy 2 ай бұрын

about to tackle this next month. Thanks for the tips and the process. Any update on your floor now? did it start to fade?

@diywithandrew 2 ай бұрын

Awesome! I think you’ll be happy with it. The only thing is if there is any spot exposed to the sun, don’t put the clear coat in that area. Otherwise it’s awesome. I’ve got an update video that talks about how it’s lasted if you want to check it out on my channel.

@BrianMason3636 Жыл бұрын

Very nice job thanks for sharing

@diywithandrew Жыл бұрын

Thank you!

@scottyahol Жыл бұрын

great video 👍🏻I bought the same kit,But didn’t put on the final clear coat. Can I put that on a year later.Still looks great ,

@diywithandrew Жыл бұрын

Thank you! Yes I think you could. I might wipe down the surface once with a lightly damp cloth just to make sure it's clean. I highly recommend doing the clear coat.

@VivekDhingani 9 ай бұрын

I have just done that boxing but haven't put the clear coat on it yet. I'm debating whether I should put the clear coat or not because its price is almost the same as the epoxy kit. Also worried about the floor getting slippery after the clear coat.

@VivekDhingani 9 ай бұрын

Also, I was reading the clear coat instructions and it says you should put the clear coat within the 5 days of the epoxy done. Curious how your clear coat is holding up now?

@jackcavanaugh_callc 7 ай бұрын

Castagra’s Ecodur product fills cracks and self levels if anyone’s looking to save some steps. It also has extreme adhesion so you can get away with doing much less prep work

@diywithandrew 7 ай бұрын

Great to know.

@ChrissyLoveBK Ай бұрын

Beautiful

@diywithandrew Ай бұрын

Thank you!!

@marysolcolon9477 Ай бұрын

So nice. Love it

@diywithandrew Ай бұрын

Thx!

@jayjay-tx1vy Жыл бұрын

Nice work looks good

@diywithandrew Жыл бұрын

Thanks!

@squadman3376 Жыл бұрын

Painter here. Did you use a 1/4 inch nap roller? Maybe a 1/2 nap would apply a bit more for a thicker layer?? Great prep and job. Cheers.

@diywithandrew Жыл бұрын

I think it was a 1/4 nap. Great tip on the 1/2 nap. Also thanks for the kind compliment. Knowing your a painter makes that high praise. Thanks!

@fordfalconsforever 7 ай бұрын

Could you do a follow up video to give a longevity review or a response comment please? Thank you for taking the time to make this video, it was helpful. If you've already made another video, could you link it for me? I couldn't find one.

@diywithandrew 7 ай бұрын

Sure thing! I just finished it. The video be live tomorrow morning. Here is the link. I hope it is helpful. kzfaq.info/get/bejne/Z7ifqKmVmsmYiYk.html

@roywhitman7109 Жыл бұрын

Looks great!👍

@diywithandrew Жыл бұрын

Thank you!!

@sameeranandtorvi Жыл бұрын

Great work. Looks nice !!! I love how you have arranged your show rack at some elevation. How did you do that and where did you buy it?

@diywithandrew Жыл бұрын

Thanks! I bought the shoe racks on Amazon here: amzn.to/3Lc8zo9 //For the price you can't beat them and they have held up really well. I then bought 1/2" copper pipe straps to mount the bars to a piece of scrap wood I mounted to the wall. You can find those on Amazon here: amzn.to/3Nm4yjG

@sameeranandtorvi Жыл бұрын

@@diywithandrew Thanks a ton. such a great idea to lift it up so that the floor can be easily cleaned :)

@diywithandrew Жыл бұрын

@@sameeranandtorvi Absolutely! We love it.

@larscajvall5804 Жыл бұрын

Love it! Regards from Sweden.

@diywithandrew Жыл бұрын

Thank you, Lars! Great to hear from someone across the world. We have good friends who live in Sweden as well!

@chriswalls5831 2 ай бұрын

May have the garage done like this nice

@diywithandrew 2 ай бұрын

Right on! We love it.

@michaelbruce3773 Жыл бұрын

I did my three-car garage it required an exorbitant amount more than it required on the box. Additionally using the professional grade epoxy clear top coat was necessary to get the shine out of the floor I looking for.

@diywithandrew Жыл бұрын

Like I said in my video I agree that it takes more than what they give you. I find that frustrating and am surprised they have not corrected this. The consumer should have left over not less causing an additional purchase. Thanks for sharing.

@sylviayoungman6925 Жыл бұрын

I watched the video twice. I am planning to paint all walls in my 3 car garage interior and then epoxy with chips and seal. What is the estimated cost (from cleaning to sealing) to do the garage floor, if I do the project vs a seasoned pro? Very inspired watching your video. 😊 Were you able to clean the garage floor and do the epoxy work and spread the chips and seal it in one day?

@cwqrpportable Жыл бұрын

@@diywithandrew You’re right and it’s all about the $$. Entice the home owner to purchase the product as cheap as possible and worry about the rest later.

@peggyB7835 8 ай бұрын

The prep work is the most important if you want a floor that lasts. Any complaint reviews I read about it peeling up, I guarantee it is due to a lack of prep. Commit to a two-weekend project. Maybe even three. This way you won't rush or cut corners. After several years my floor still looks brand new. One time, my hubby and a friend were moving a metal shelving unit, I heard a loud scraping. I ran over expecting a long gash through the paint. Nothing. Hard as nails. I feel it had to do with having patience to focus on the importance of prep work.

@amanrayat7215 9 ай бұрын

What is the cost of this flooring( per square foot )

@diywithandrew 9 ай бұрын

Unfortunately it varies based on all sorts of factors. It’s been so long that I can’t remember how much it cost me but I know it was significantly cheaper than having it “professionally” done.

@devinjohnson9528 11 ай бұрын

Hey there, thanks for the thorough talk though. I’m just curious, I’m currently in the process of doing this myself..I think my garage was sealed so in addition to degreasing/etching I ended up getting diamond grit sander from Home Depot..it did make the surface a bit more gritty but it still felt smooth-ish. I am curious if you remember what condition your garage concrete was in? And have you had any paint peel up or “hot tire” marks? Again great video!

@diywithandrew 11 ай бұрын

Thanks for watching! It was in pretty poor condition. I think you did the right thing sanding it down more. I haven’t had any issues with it in over a year! Thanks for the nice comment too!

@devinjohnson9528 11 ай бұрын

@@diywithandrew do you remember what the texture was before you applied the first coat of epoxy/paint? Did it have some texture? Or was the surface relatively “grippy” (for lack of a better term) from the etching rather than “gritty” like actual concrete?