Jayson from O'Neill Brothers Racing shows you how to quickly start a flooded engine
Пікірлер: 48
@johnnyrobinson1197 жыл бұрын
Just did this to my Gsr with a g340 reed case worked instantly! You guys are truly the best when it comes down to getting in touch and answering questions. Goped almost took off on me though lol had to catch that shit fast!
@highflying824 жыл бұрын
Watched this a few days ago .. tried it today .. it works every time
@mooremaceo5 жыл бұрын
Just bought a Redcat Dunerunner and could not start it. Tried this and it runs perfectly! Thanks!!!👍
@DVICK839 жыл бұрын
Good advice thanks Jason... Sean told me this trick many years ago... Bravo nicely done
@demonetizedhistory58062 жыл бұрын
Yooo this trick actually works legit. I ignored everything and tried this on my Baja 5b and it worked on the first try. I took off the 4 base screws to split the bugger in half then disconnected the fuel pipes to the carby then took off the air filter then the carby. I cleaned the carby (which was filthy from the previous owner) with some fuel and a tooth brush and good it shiny again then pulled the pull start and on the first try I heard the engine start and make a engine sound lol then did it again to make sure and it was just a regular sound so I crossed my fingers and put the carby and air filter back the same way I took it off then connected the fuel lines and connected the engine to the rear body with the 4 screws on the base plate then I primed the bulb thing on the carby and put the choke in the vertical position. I then primed the cylinder by pulling the pull handle slowly a couple times like 5 times then I pulled the pull start hard and after 2 attempts I heard a popping sound like it wanted to start, I took zero chances and straight away flipped the choke to the horizontal position and pulled the pull start about 2 times which made the normal flooded sound but on the third time it started right away and man it was the best feeling ever, I feel like a actual mechanic now, my own father believe it or not thought I had failed with the RC car cos I bought it second hand, he thought it was broken and even told me to my face that I bought a broken RC car and was laughing but my god did I prove his arse wrong haha. I ran the engine for about 5 minutes then turned it off, installed the servo thing for speed then adjusted the throttle settings on the flyski remote cos the thing literally drove off as soon as I started it for the second time lol and crashed but thankfully it was into soft stuff in my garage but tbh was so close to going onto the street hehe 💀. I tuned the bugger then started it every time by holding the back of it up so the thing doesn't drive off. After a lot of trial and error I got it and man now it's a dream but only thing is that I have to push the trigger away in the break position for it to move forward haha but it doesn't bother me really tbh haha. I have to say thank you to these blonde gangsters for having the best video of how to do this online, I can't thank you guys enough for making this video. If this video was never posted I'd never had known how to fix it. THANK YOU!!!
@sergeantlimpdk72455 жыл бұрын
That's awesome! Thank You for making this video
@billsellers95095 жыл бұрын
Thanks a real time saver
@idiymybest21518 жыл бұрын
So on a car like a 5ive that doesn't have a plug protector, or maybe even a 5T or DBXL that has had the plug protector removed, would you still recommend this?
@Harleyfunman5 жыл бұрын
worked perfectly !! tks
@mumforddale19 жыл бұрын
thanks never knew that bro!
@bradleypendleton2025 жыл бұрын
Very nice but if it’s in the car like a baja this would take longer than taking the spark plug out
@kenneth4098 Жыл бұрын
Good info
@katrellbrower8238 Жыл бұрын
Thank you so much I was gonna throw engine in the garbage
@skycorrigan6511 Жыл бұрын
Is it possible to spray starter fluid in the intake to start it if it's flooded?
@raymondwoodhouse92676 жыл бұрын
Yeah same here,never knew that.......thanks
@josequiroz55 жыл бұрын
Hey can you do that on a redcat rampage mt
@wdavie2711 ай бұрын
Hiya dose this clear all the petrol out of the crank casings my friend
@demonetizedhistory58062 жыл бұрын
Dude r u Jesus cos this might actually work for my situation, im a noob so idk much bout engines especially the carby which seems like rocket science but hopefully this works.
@idogolan80154 жыл бұрын
Can you guys make an tune video for twin engines?
@Aj-om4dt5 жыл бұрын
You guys certainly know what you’re doing 👍
@ysrcutoo19 ай бұрын
Bro...my baha 5b engine starts but after few seconds stalls..sometimes it gets flooded too and hard to start. I cut the fuel supply then it starts again..what could be the reason
@Daniel-jw3of5 жыл бұрын
What is this engine called??
@str8roller_68015 жыл бұрын
Couldn't I lean out my needles so that the carb only sucks air no fuel?
@Papa7Bravo9 жыл бұрын
Just would like to ask you guys in hope that my problem can be fixed. My Baja starts, and will run like crap, if I bring in the throttle slowly to keep it running it tries to stall, but if I give it full throttle is revs up but doesn't rev that high at all, the idle it'll try to die, I've tried adjusting the mixtures but nothing helps, I am using stock needle settings for the 990 carb on a 30.5, I've changed all the top end gaskets twice, brand new spark plug, good spark ect. just runs terribly.
@oneillbrothersracing9 жыл бұрын
***** You might have a bad carb if it's not responding to tuning. I was going to say air leak as well but it sounds like you've already replaced the gaskets.
@Papa7Bravo9 жыл бұрын
***** Thanks, if I remember correctly back when all this started it was doing it with the stock carb. Also for some reason I keep thinking a cracked insulator block at the moment, I just have the stock plastic one and we had a couple of days of heatwaves (Well, like normal weather for you guys) But I had been running for I think 3 days back to back each day bringing it out to bash but the last time it was fine for 10 minutes, then I lost top end power, then later the bottom end was playing up a bit and then when I brought it in the idle was a bit funny.
@oneillbrothersracing9 жыл бұрын
***** You're welcome. A cracked or warped manifold is possible. The engine could also be drawing air through the crankcase seals.
@Beatman9389 жыл бұрын
***** What about if the prime bulb will not prime on the wt 997, do you have a solution for that
@christopherperdue9772 жыл бұрын
Only problem I have with this method is if I'm using anything other than Teflon gaskets I don't reuse the gasket so this can potentially get kinda expensive if the engine gets flooded often.
@Body_Dropped3 жыл бұрын
I just got a new G290rc installed and left it idling just fine for awhile to break it in and it just shut off so it wouldn't start after and I primed the carb a bit more and shows no signs of it wanting to start can you help me
@blackhawkdown266619 күн бұрын
Mine is doing same thing brand new Zenoah 32cc ran it twice went back out acted funny stalled out let sit for few started back up went to take off and stalled now won’t start back up and haven’t got it broke in yet
@roynelson76139 жыл бұрын
Hey man you guys always have the best videos ever I don't care what anybody says dan the Man that dude rocks bro he's amazing mechanic I've never seen you before but glad to meet you bro on the KZfaq that was awesome video thanks buddy always a thumbs up with me tell Dan I said hello thanks for subscribing to my channel I gave him a big shout out on one of my videos thank you buddy👊👊👊👊👍👍👍
@oneillbrothersracing7 жыл бұрын
Thanks Roy, I'll pass your message along to Dan.
@Gaboi14 ай бұрын
For some reason it didn't work for me any help would be greatly appreciated thank you
@bubbanater19848 жыл бұрын
You say 1 and and 1/8 to 1 and a1/4 on low and 1 and 1/2 to 1 and 5/8 on high end is this from totally snug down 1 and a 1/4 turns out from bottom or what just to clarify. I my have mine tuned way out of spec to even try to start.
@oneillbrothersracing8 жыл бұрын
Turn the needles all the way in and then back them out. These are base settings and will require fine tuning. They're just a starting point that should be close.
@bubbanater19848 жыл бұрын
+Sean O'Neill ok thanks, I have another question if u don't mind what is the correct setting for the idealer screw mine isn't starting at all it floods on second pull. I can pull the carb as u describe in video and it will run just like u show it does but after I put the carb back on and adjust it like u have here nothing any ideas would be a great help thanks
@fdogdog14 жыл бұрын
Ok I did it and it didnt work
@BajamanCam9 жыл бұрын
Can't you just hold it WOT? At least that's what I do.
@enlightenedtrucker7396 жыл бұрын
Or just carry a can of start ya bastard engine start.
@commodoreman329 жыл бұрын
hmm doesnt work for me
@oneillbrothersracing9 жыл бұрын
commodoreman32 If this method isn't working the engine is either not flooded or there is another issue such as a bad carb or ignition.
@FullSend936 жыл бұрын
Sean O'Neill so mine wouldn't start . It started for a second then shut off and that was after cleaning the carb. Also put a fresh spark plug..my guess is a bad carb?
@tanveersangha69646 жыл бұрын
Iv tried this many times on all of my 5th scale rc's. It doesn't work!
@enlightenedtrucker7396 жыл бұрын
tanveer sangha I just use a can of start ya bastard engine start. Works every time.
@hillarynunya37703 жыл бұрын
Maybe your car isn't flooded This works perfectly everytime