Finally undervolting 5800X3D - PBO2 tuner and how to do it

Рет қаралды 43,466

8 ай бұрын

Link to PBO2 Tuner: drive.google.com/file/d/1OswZ...
Ryzen Master: www.amd.com/en/technologies/r...
Cinebench: www.maxon.net/en/cinebench
Current setup (used for benchmarks as well):
RTX 4090 Suprim - amzn.to/3ZVHhIH
Ryzen 5800X3D - amzn.to/3VufUmo
Asus B550-I Strix Gaming - amzn.to/3Vf2qLI
Arctic Liquid Freezer II 280mm - amzn.to/3gJx40D
Patriot 32GB (2x16GB) 3600MHz CL18 Viper Steel - amzn.to/3JIzTL1
be quiet! Pure Power 12M 1000W - amzn.to/3leDOG0
Samsung SSD 970 Pro 1TB with heatsink - amzn.to/3XHhZNF
Lian Li O11 Air Mini - amzn.to/3XEbACX
Above are affiliate links

Пікірлер: 162

@leizerg 4 ай бұрын

hi everyone! I'm getting a lot of question about setting up other parameters. Here's an example on how to do it: -30 -30 -30 -30 -30 -30 -30 -30 120 75 110 0 120 is the PPT 75 is the TDC 110 EDC 0 means no change for the rest of parameters. Set the values to your preference - this is just an example

@WillPlaysGames1993 3 ай бұрын

i already had mine set as -30 for the cores im going to try the ppt/tdc/edc now since mine runs around 40c idle and almost 80c under a load with an artic 360 aio (same one gamers nexus uses to be exact)

@Bonekk1992 2 ай бұрын

hello, it might be a stupid question but can i replicate everything u did on my r5 3600 (i know my cpu have 6 cores but u know what i mean)? my goal is higher performance, maybe should i just go for simple oc? what's ur opinion? since 3600 is not that hot

@leizerg 2 ай бұрын

@@Bonekk1992 i would start with OC. 3600 shouldn’t get too hot

@WillPlaysGames1993 2 ай бұрын

@@leizergwas about to say the same but also set it to 1.2 volts at the max speed (its what i did with my 3700x before i upgraded to the 5800x3d)

@Bonekk1992 2 ай бұрын

@@leizerg Rn im on 4050MHz, 1,275V vcore- hwinfo showing lower 1,256 (idk why) in stresstest and 1,272 in idle. Im using prime95 "Smalleset FFts (l1/l2 cache, high power/ heat/ CPU stress). After 20minutes of test i have 0 errors and 88% C temperature on full of dust fera3 never cleaned since i bought my pc (4 years) xD In ryzen master stresstest i had 92 degrees. Imo its acceptable since im just playing cs2/ watching yt so i will never have this kind of temps. What do u think? Is prime 95 good enought stability test?

@Clust3r-1Alpha 3 ай бұрын

great guide thankyou. i upgraded from a 3800XT to the 5800X3D and my 3 Fan AIO was going wild. adjusted some fan curves and followed your guide and I've dropped roughly down to 70 while under load and my fans are quiet. exactly the result i was after.

@fried_out 3 ай бұрын

Thanks for the quick info! Added the values in BIOS and its working like a charm at -30. I'll try it with lower values at some point to see how far down can it go.

@derekb117 6 ай бұрын

cheers bro, no fluff and straight to the point. very well clear and concise, On the MSI B550M PRO-VDH WiFi AM4 (latest BOIS i can use PBO with curve optimizer

@Beardroid91 5 ай бұрын

Thanks the good setup guide, i had tried this in the past on my 5800X3D, but never worked quite right on system wake up's, but now it works well, running with -30mw for now, and saw a 600 point gain on my 3DMark Time Spy benchmark, so clearly works. :)

@VidocqCZE 4 ай бұрын

Thanks for this! I just set -10 on every core and got up to -10°C which is crazy, for me, it was just around the drop when my AiO fans start to be noisy so now is everything nice and quiet. And for people wondering why this and not the BIOS setup well at my ASUS X570 TUF you need to tinker with a bunch of functions in BIOS, some of them are not even that related to CPU and even with detailed videos I was honestly afraid to do that, if you have native PBO Curve setup in your BIOS as some AM5 MBs just roll with it is of course better option.

@Duthjoods 7 ай бұрын

Did not work for me at first. Apparently when you have "fast boot" enabled in BIOS the system doesn't shut down completely, so no cold boot and it won't trigger. What worked for me was setting the trigger to "At log on" instead of "At start up" ...maybe that helps someone who's struggling with this.

@leizerg 7 ай бұрын

Thanks for sharing! I’ll pin this comment so anyone can see it.

@leoilios 2 ай бұрын

i also had to move the pbo tuner folder out of downloads for the task scheduler to read it. i just moved it to the root of my c drive

@t-roller9958 4 ай бұрын

LOL, from max 87 degrees to max 81, and from a steady

@TheTimeIsNowBaby 7 ай бұрын

Thanks man!!! PBO enabled on my 5800x3d.

@sitdxwn2376 5 ай бұрын

i was able to use PBO on my current bios version with my ryzen 5 5600x, i just put in my ryzen 7 5800x3d and the pbo / some overclock settings have dissapeared. This is now the only way i know of to undervolt, i thought maybe i could update my bios but for whatever reason the download button on asus website isnt working on the latest version LOL if anyone has any suggestions that would be sweet.

@camjohnson2004 5 ай бұрын

Ok so i just tried this with my 5800X3D. Now i am using a custom loop with 2x 360 Rads (keep in mind i'm using 1 loop to cool the CPU and GPU) Running multiple 30 min loops of CBR23 i was able to use -50 on ALL 8 cores and it was rock stable TY for your guide, very helpful

@leizerg 5 ай бұрын

-50 is crazy!

@camjohnson2004 5 ай бұрын

@@leizerg I reckon I could have gone higher but the app only goes down to - 50. Was rock stable and it would hold 4492MHz through Cinebench from star to finish at a Max temp of 67.9c

@gwonzz 2 ай бұрын

i just got a 5800x3d gonna drop it in tomorrow on a b550m ds3h mobo with 32 gb ram and a rtx3080 12 gb card i will try this you got a sub and a like !

@635_ 4 ай бұрын

from 92c to 78c, amazing. i have a nzxt x63 and was constantly running at over 70c-80c when at just 50%-60% usage. Now my cpu never even goes above 70c while playing games. tysm

@_pant0m 2 ай бұрын

what settings?

@635_ 2 ай бұрын

with the same settings as he uses. Btw just make sure to make pbo2 start at login and not at startup, thats one issue that i had.

@ChoJun69 9 күн бұрын

I went from 90-91 to 76c myself too, it was crazy lmao. I was so scared on first test without PBO, it literally jumped to +90 instantly

@KroryykDB 7 ай бұрын

Wow this really does make a difference, in R23 my cores were only boosting to 4.28-ish and after applying -30 not only is the temp almost 8ish degrees cooler they all clock to 4450 which is what they should be OCing to. Thanks! Also my cinebench score went from the lower 14000s to 15290+ with programs running lol.

@leizerg 7 ай бұрын

Great to hear!

@KroryykDB 7 ай бұрын

@@leizerg It's just too bad I have to always manually apply the undervolt whenever I start up windows. Is there a way to have it do it with windows startup?

@leizerg 7 ай бұрын

@@KroryykDB yes, it’s in the video. Should work. Otherwise maybe try bios or your motherboard manufacturers software.

@KroryykDB 7 ай бұрын

@@leizerg Oh my bad, my ADD is showing lol. My specific motherboard does not have any tuning options for undervolting unfortunately and I flashed the newest bios too. I have the Gigabyte Aorus B450 Pro Wifi. Edit: I followed the video, did it properly but it doesn't start up when I reboot.

@LoserInChief 3 ай бұрын

Went from a 2700 to 5800X3D and my old AMD air cooler can't keep up,. I was spiking at 91c even after reseating and re-pasting. I have ordered a dual fan air cooler, but I may consider undervolting as well. Thanks for the guide!

@leizerg 3 ай бұрын

Definitely do it. I’m using a small noctua tower cooler and it maxes out at 82ish

@karlhungus545 2 ай бұрын

I'm not sure what you guys are doing, or maybe it's the motherboard or the pairing with the GPU, but I installed mine yesterday and have been testing it out (MSI B550 Gaming Plus MB, 4070ti) in Cyberpunk at 1440p, high settings, RT enabled, and I haven't see it get above 54C, which means my CPU fan is running at under 60% (fan curve in BIOS). This is with my quite old now CM Hyper 212 Black/RGB air cooler, and no undervolting yet. It's running at a steady 95fps and 4450MHz according to Afterburner and HWInfo64. It's also in a LIAN Li Lancool 216 case, which is a very nice case, but still...

@RonniePeterson Ай бұрын

But what were your settings in the BIOS for CPU ratio and voltage? Auto, manual, what?

@andreinpc 3 ай бұрын

On my 5800x3d with a 40$ air cooler i have 77C in Cinebench r23 and 35C in idle. I set in this way in bios on a b450 motherboard: -30 on all cores -100 PPT -70 TDC -100 EDC It's working great, in load always 4450mhz without downclock. In games i have 52-56C temperature. No other settings applied or other tweaks to break up your Windows.

@teo3746 Ай бұрын

how did you do it on a b450 motherboard haha i cant find the settings

@nightmagegirl Ай бұрын

this helped me at cinebench all core stress from 90 -91 to max 83 whitout the -30 on all cores but the other things,now i need to figure it out to put it on startup:)

@andreinpc Ай бұрын

@@teo3746 you should have something in your BIOS called "Precision Boost Overdrive" set it to "Manual" under that you must have "PPT limit, TDC limit, EDC limit" Before all of that you must update your BIOS to the latest version from your motherboard brand(Asus, Gigabyte, AsRock, etc.)

@Pand0rasAct0r_ 19 күн бұрын

i simply use combo strike 3 so (-30) on my MSI B450 Gaming Pro Carbon AC. and paired with an arctic freezer 240 II is doesnt get higher than 78 degrees under cinebench24 multicore for 10 minutes and runs at 4450mhz

@nightmagegirl Ай бұрын

I did all the steps except the one to make it at restart do the same thing cause in benchmark is same 90 degrees on mine didnt changed :(sadly idk what to do...i even had 99 percent on cpu usage and didnt worked...i have liquid cooling and my pc is 1 y old..any ideas?:(

@piquetbmjoga 5 ай бұрын

Hey bro, how's it going? I hope everything's fine, How do I set " LIMITS OPTIONS" to be automatic. You only explain for the "CURVE" but we also have " PPT" "TDC" "EDC". I'd like to know what I need to type for the parameters of these options to be automatic as soon as my PC starts.. Thanks in advance!!!

@leizerg 5 ай бұрын

Hey! Honestly I would just ignore them if all you want is to undervolt your CPU.

@KeyOfNotebookGaming 5 ай бұрын

CO Mode shows me in Ryzer Master app CO - Off. Why ? why pbo2 does not applying settings ? Can somebody tell me?

@alexbedini731 5 ай бұрын

Great video! Coukd you do the same but for bios pbo2 settings? I do not like to rely on software when it comes to cpu oc

@leizerg 5 ай бұрын

I’ll need to check if my mobo supports it :) plus it can be a bit different for each mobo but I’ll try

@Daz555Daz 11 күн бұрын

Eveet mobo manufacturer puts their settings in different places in the bios which makes a video about it less helpful. You just need to search for PBO Curve Optimisation or similar in your bios and set a negative value. Start with something like negative 15 and go from there. I'm running negative 30 on all cores.

@mihnea2.0turbo98 26 күн бұрын

My setup is -25 all core , 120 / 75/ 110 limits and tested for weeks with 360mm arctic freezer 3 i run benchmarks in max 71 72 and cs2 in 55-61 celsius 😅 up to 10* improvement and it’s stable at 4449 99% of the time

@Xrosss 4 ай бұрын

I dont recommend cinebench for stability testing. Rather use OCCT for stability at max performance.

@leizerg 4 ай бұрын

Might give it a try - thanks for sharing!

@mariuszgorecki5502 2 ай бұрын

@leizerg Hello, do you know why the PBO tuner may not read ppt, tdc, edc limits? They are at zero.

@leizerg 2 ай бұрын

No idea, but does it auto set on restart?

@axp2579 3 ай бұрын

Hi Leizerg, first thx for this Video. I tried -10 and -20 and both times what happens confuses me...instead of getting better temps, my temp rises! Off course allso the Mhz rise from 4250 to 4350 but also the Watt conspumption rises from 95 to 105/110 and the temps as I said rise from about 73 to 80 Celsius. I tested with cinebench for 5 minutes. Its like, yes I get more performance but also higher temps...am I doing something wrong?

@leizerg 3 ай бұрын

Did you use the app? Or bios? Or made changes in the auto run? Either way this seems weird …

@axp2579 3 ай бұрын

@@leizergNo changes in BIOS and autorun - I did exactly as instructed in your video via PBTuner

@leizerg 3 ай бұрын

@@axp2579 well that’s unexpected. Does it happen the same if you just use PBO2 app? I would clean the registry autorun, set manually via PBO2 and check if it persists. If not then maybe there was a small mistake in autorun config.

@djenergy91 2 ай бұрын

Try a + instead of a - 10....

@kenny10497 Ай бұрын

why not set in BlOS ?

@SV-01 7 ай бұрын

Hey i have a 5800x3d ,6800xt ,16gb corsair vengence , deepcool ak620 , b550 mag tomahawk max wifi ,deepcool 1000wt , wd 2Tb . My pc can run games at 2k with more than 100 fps for hours, temp for both cpu and gpu reaches 76 (80 in rare case for short duration). But some times when i open chrome, vlc, obs ,davinci my screen flickers and later on my mice freeze . Is there temp issue or something else in such case?

@leizerg 7 ай бұрын

I sometimes have the same, on photoshop for example my screen goes black. Did you overclock anything?

@SV-01 7 ай бұрын

@@leizerg No OC, other info: its windows 10 pro , all apps are 64 bit , xmp profile 3200 mhz .

@leizerg 7 ай бұрын

@@SV-01 tough one. I dont think I have anything that could help you, still havent found solution to my error.

@antho2935 6 ай бұрын

Check chrome settings and make sure hardware accelerate is enabled

@RandomNameMy 7 ай бұрын

Better off just setting this in the bios. Though I suppose the app could be used as a quicker way to find optimal value to then set in the bios.

@akooma3694 6 ай бұрын

No doable in bios with X3D chips, overlocking settings are blocked

@RandomNameMy 6 ай бұрын

@@akooma3694 Must be an AM4 x3d thing, because I set all my PBO curves in the bios (7800x3d for reference) and can optionally set them directly in Ryzen Master as well.

@akooma3694 6 ай бұрын

@@RandomNameMy damn god knows. I just run PBO2 tuner and set it to -30 every time I start up. Its tedious I wish it worked normally for me like it does you.

@RandomNameMy 6 ай бұрын

@@akooma3694 Definatly sounds tedious.

@bagchief 6 ай бұрын

@@akooma3694Try a bios update on your board. I have a ASUS Strix X570i on the latest BIOS and PBO is available.

@ToxicKingSui 6 ай бұрын

Hi I’m fairly new to all these, can we go lower than -30? Like -40 -50 so on? If not, why? Thank you in advance!!

@leizerg 6 ай бұрын

I believe going below -30 will noticeably impact your performance.

@ailandassulcas 6 ай бұрын

Windows keeps trying to run the PBOTuner as admin all the time and therefore the task scheduler part does not work for me. I removed the run as admin option in the properties as well and nothing changes. Any ideas?

@leizerg 6 ай бұрын

What about bios? Can you set pbo there?

@ailandassulcas 6 ай бұрын

@@leizerg good question. I have zero knowledge when it comes to BIOS and in fact I'm too worried to break anything. Perhaps something to look into but for now I just set up to run it with the undervolt figures in the properties so I just run it from the desktop, it appears for a second and disappears and applies everything. Takes like 5 seconds but still not as good as autorun. 😅

@VidocqCZE 4 ай бұрын

In the task scheduler you can set "Run with the highest privileges" works for me at least with similar error.

@tKcs2 4 ай бұрын

Yeah but should i do it with a ryzen 5 5600x rx 6800xt cs2 is running at 150fps sometimes down to 100...... ive even seen 80 im starting to think i have a broken card.

@leizerg 4 ай бұрын

Looks like overheating issue - did you check temps on gpu/cpu?

@azegzawabarkan8680 14 күн бұрын

they both hit the limit of 90degrees celcius, with -30 or without. How can i know if any changes has happened? i guess its because i use an amd wraith prism.. i bought a darkrock pro5 cooler but it doesn't fit in my case, i wasn't expecting the cooler to be this big

@azegzawabarkan8680 14 күн бұрын

okay, i just tested it by putting it all back to 0, i reach 90degrees much faster and i get 700 less points on the testing than i did with -30

@leizerg 14 күн бұрын

Yes the cooler isn’t enough for this cpu unfortunately

@ChoJun69 9 күн бұрын

x3d are notoriously hot cpus, you want to invest in really good cooler if you plan to use it. I personally went with Deepcool AK620 Zero Dark and my temps with -30 under cinebench test is ~77c. Although my living area is constantly +25c and my desk is old with shitty airflow for my case( if i take out the case from desk its easily another -5c if not more, i just have no place to put pc. So next big buy for me is new desk lol

@Merkah 3 ай бұрын

ive done all this but when i reopen my turner it says its all on zero? on the app but in the task sche its got my task that i made is this common ? bcoz i then turned of my pc and then did a bench mark and it was 3k less and my PBO2 was just reset to 0 on all 8 cores?

@ObakuZenCenter 2 ай бұрын

Don't use any guides that use only Ryzen Master. Changes should be made in the BIOS, are recommended by AMD themselves.

@carloscorona3143 9 күн бұрын

How do I know if the pbo2 tuner is running un startup ?

@ChoJun69 9 күн бұрын

Open PBO turner and check, if it has -30 or w.e. you setup without you doing anything then its working. Also just do the cinebench few seconds to see how high your temps go when you compared without pbo and with it

@quqp 2 ай бұрын

Hey, can you help my I just got my 5800x3d but in game its only running at 3,4ghz do you think PBO Tuner will help? I also have amd stock cooler for now😢

@leizerg 2 ай бұрын

Update motherboard bios, do PBO2 or bios tuner and it should help. As soon as you can get a better cooler

@quqp 2 ай бұрын

@@leizerg So should I leave it how it is right now? I have a b450 aorus m and I downloaded all newest bios and drivers.

@quqp 2 ай бұрын

@@leizerg Should I do PBO2 Tuner now? Or wait for a better cooler

@Antonio-rg1cy Ай бұрын

why not going with -offset then - then 0.05 ? I did that on asus tuf b450-pro gaming in bios

@wc.j3911 Ай бұрын

How was the temp and stability?

@Antonio-rg1cy Ай бұрын

@@wc.j3911 before i did that on cyberpunk my temps was going 84 c now is 75 76 max

@wc.j3911 Ай бұрын

@@Antonio-rg1cy awesome! thanks for the info

@iamgp3313 Ай бұрын

Why would you not just use kombo strike? It does the same thing and it’s much easier to set up.

@vangledosh 3 ай бұрын

I cant change PPT, TDC or EDC. All the values say 0 and if I try to change it in PBO2 it says "CMU status failed"

@MistuhChai 16 сағат бұрын

Do you happen to have Valorant installed? If not, reinstall your chipset drivers. If you have Valorant, you will not be able to use both at the same time as Riot anticheat blocks the "inpout.exe" making pbo2 tuner unusable.

@RonniePeterson Ай бұрын

I thought Ryzen Master did not work with the 5800X3D, so what is going on here?

@leizerg Ай бұрын

You can monitor it but can’t change anything.

@nedimaydin7876 4 ай бұрын

at 4:01 ı wrote 8 -30 but ı want to make it change my ppt tdc and edc every time ı start the pc. how can ı do that? help me please sir

@leizerg 4 ай бұрын

I have no idea :) I’ll try to find it though

@nedimaydin7876 4 ай бұрын

@@leizerg ı'll be here if you figure it out. You have a sub 👍

@leizerg 4 ай бұрын

I think I found it. So this is how you should set it: -30 -30 -30 -30 -30 -30 -30 -30 120 75 110 0 120 is the PPT 75 is the TDC 110 EDC 0 means no change of course set the values to your preference this is just an example @@nedimaydin7876

@nedimaydin7876 4 ай бұрын

@@leizerg thanks man ı will try it and come back here after

@GuharoLeon 3 ай бұрын

@@nedimaydin7876 it worked?

@KamyoncuWade 2 ай бұрын

+10 degress with all -10,-20,-30 :D i guess i m staying stock ^^

@Ioan-Ni 5 ай бұрын

I did all the steps correctly and upon restart, nothing. Back to 0 everything. Doesn't work. Works from bios. Nvm.

@leizerg 5 ай бұрын

BIOS is the better way, this is more for anyone who doesn’t have this option in bios :)

@jordybaaij8314 2 ай бұрын

@@leizergI also on startup or log-on they keep going back to 0. any fix?

@gordonhowitt 5 ай бұрын

Probably a dumb question: Before I use the PBO2 tuner, do I need to enable any settings in the BIOS (Gigabyte Aorus board)?

@leizerg 5 ай бұрын

No. You can do the tuner on your board if it supports it btw.

@MrMassacre157 4 ай бұрын

I used -30 in all cores and 100 PPT 70 TDC 100 EDC i get - 20c in the final result so crazy

@MrMassacre157 4 ай бұрын

i needed update my bios to do it*

@michealmeyers9789 3 ай бұрын

With this settings your cpu won't clock 4450mhz if you don't and prefer cooler temps than it's perfectly fine.

@gunslinga7077 Ай бұрын

Why use this instead of tweaking in bios real quick?

@ChoJun69 9 күн бұрын

A lot of mobos didn't had bios option to tweak PBO curves back then, now afaik every single one of them has it by now(that support the function), so this kinda is not necessary as you can just go to bios and do it there without fiddling with extra stuff.

@kurok1tenshi 8 күн бұрын

X470 series won´t support it for example, only some x570/b550 have it on the bios.

@JMUDoc 6 ай бұрын

Don't trust Ryzen Master - its predictions are VERY generous; use RM as a starting point for Core Cycler. Also, BIOSes now support Curve Optimizer for the 5800X 3D. No need for PBO2Tuner.

@leizerg 6 ай бұрын

Not all do, at least not with a simple click. Some have PBO tuner built in but for example mine requires a bit of tinkering. Plus I still find PBO2 to be the easiest way to test for instabilities.

@JMUDoc 6 ай бұрын

@@leizerg AI agree that PBO2Tuner is the best way to change the CO values on the fly, for testing purposes, but I would never use it long-term if my BIOS supported CO.

@leizerg 6 ай бұрын

@@JMUDoc makes sense 👍

@trevordroog7638 4 ай бұрын

I can agree here. I have a B550 Gigabyte motherboard and have updated it to the latest bios and there is still no feature to undervolt the 5800x3d cpu. PBO2 is the only way I can run with an undervolt.@@leizerg

@ObakuZenCenter 2 ай бұрын

@@trevordroog7638Don't add another undervolt setting. Use the Curve optimizer and any other settings in the BIOS itself. Don't use software to do it and do not follow this guide. It's outdated and no longer accurate.

@CsFanatiker 2 ай бұрын

Just change it in bios no programs needed

@gwonzz 2 ай бұрын

How do you change in bios I have a gigabyte b550m ds3h I don’t want to mess up anything

@Synthetic-Chicken 4 ай бұрын

Coming from overclocking in extremes in the 90s-2000s to undervolting them out of the box seems so backwards as fuck for me. Detuning it or undervolting it for not even 10c temperature and a barely noticable clock speed doesn't seem worth while when you can just make custom fan curves and simply turning the fans up negates more then the undervolt. I might of got lucky with the silicon lottery but I havent undervolted and I never see temps over 75c in gaming and real world stressful environments.

@leizerg 4 ай бұрын

All depends on what you have, for SFF builds (like mine) it really does help. Plus you dont lose anything from UV, no performance loss and better temps, meaning you can run your PC quieter. But, 75c is pretty great so no need to bother imo :)

@esaedvik 4 ай бұрын

Anything AMD nowadays is worth trying to undervolt for a bit of extra clock speeds and less heat. Nothing backwards about it, apart from AMD not doing so at the factory tbh, but that's what it means to be an enthusiast, you test the limits. -20C temp drop some get isn't insignificant. Just optimization.

@MegaDante4 5 ай бұрын

Just do it directly in the BIOS and forget about the task scheduler

@leizerg 5 ай бұрын

Not every motherboard can do it

@michealmeyers9789 3 ай бұрын

That's what I thought, but after comparing both methods I have to admitted that pbo ist better than curve optimiser in bios. I don't know why but with pbo my cpu remains constantly on 4450mhz also the temperature slightly lower as well as the consumption. For average user bios might be the right solution, but for cherry picker like pbo tuner combined with task scheduler is the way to go.

@Justdigit2 6 ай бұрын

Why not change this in the Bios??

@leizerg 6 ай бұрын

Not all motherboards support this.

@djbreal87 4 ай бұрын

So I followed the guide, and got great results. -30 just like you. Gained around 600pts in Cinebench, and my Temps dropped from 82c to 74c. But when I made the changes instead in my bios (I disabled/deleted the task scheduler and made sure PBO never started/was reset) when I ran cinebench again, it crashed. I adjusted my bios settings to -20 and now its stable. My question is, why did it work with the program, but not through my bios?

@leizerg 4 ай бұрын

There’s a high chance it would crash with program settings too. Instability doesn’t always show immediately, sometimes it takes a couple of runs

@djbreal87 4 ай бұрын

@@leizerg Ahh ok that makes sense then. Thankyou for the reply :)

@Yyr85 7 ай бұрын

Throttling is beginning at 80c

@Wolek96 6 ай бұрын

Throttling is beginning,whenever you set the limit in bios. And the best is to set everything in bios.

@foxxyboxxy9348 5 ай бұрын

The Tjmax of the 5800x3d is 90°C. If not set otherwise in the bios, it wont ever throttle at 80°. Spread your "knowledge" elsewhere

@user-ur7pl1rv1y 4 ай бұрын

Привет друг,будешь в России настрой мне эту программу.🤍💙❤💯🤙💪💤

@StroKing 3 ай бұрын

I have my 5800x3D on water and PBO2 set at -30 No matter what i throw at it, it never get over 44 degrees and runs solid at 4.5 GHz

@RichardMar 3 ай бұрын

Show it in a video nobody believe it

@kurok1tenshi 8 күн бұрын

Custom WC for sure no? cause i have a lian-li 360 aio and it still hits 81/83c under heavy load, repasted it with grizzly hydronaut remounted cause i thought it was not seated well and it still can reach low 80s...maybe the AIO is trash.

@ObakuZenCenter 2 ай бұрын

Do not use Ryzen Master for undervolting/overclocking. And definitely do not use PBO Tuner. Enabling Fast Boot should never be recommended either. Use the BIOS settings as intended and recommended by all motherboard manufacturers and AMD themselves.

@Rob-nv7ew 2 ай бұрын

Do not listen to this guys comment as he has no idea what he's talking about.

@sengan2475 2 ай бұрын

@@Rob-nv7ewexplain why

@G4M3RGU1D3 2 ай бұрын

boring push it to the limit like your mom fell in the staircase, full throtle!

@pelayla 2 ай бұрын

"use the BIOS settings as intended and recommended by all motherboard manufacturers" 🤓☝️

@hids7 Ай бұрын

O uso do programa é somente para facilitar e não ter que ficar entrando e saindo, após conseguir os resultados aplique na bios quando voltar você irá perceber que os resultados na bios ficam até mais refinados.

@Kamil-ug5pi Ай бұрын

can set up manually everyday? because task manager not working im gettin error 2147943140

@leizerg Ай бұрын

Yes you can but try also bios maybe you can set it there

@user-zj3xl4nk1g 4 ай бұрын

If you can PROOVE that you machine can stay on for days without crashing I would appreciate this! If you look at anyone’s over clocked under clocked setting and beleive that their machines run without problems then I have ocean front property available very cheap in Arizona! From your front porch you can see the sea😂😂😂😂😂

@leizerg 4 ай бұрын

I don’t know how I could prove it to you ;) at the same time I don’t have a reason to sugarcoat it - it has been running with no issues for months now. No blue screens, freezes, crashes on any game or app I’ve played. But if you’re concerned - just stick with stock settings and it’s all good :)

@SakFPS 4 ай бұрын

lol my setups been undervolted for months and never had issues. Maybe the occasional game crash but I also specifically play Paladins that is just prone to crash in general. CPU and GPU undervolted.

@bubbablake3983 4 ай бұрын

I've been undervolting as well as overclocking for a while now. While it's not an objective fact, a decent rule of thumb for undervolting generally is that if it doesn't crash within an hour or so, you're "stable". Whether you get more or less performance is up to your setup and methods.

@esaedvik 4 ай бұрын

Literally have run a different AMD CPU undervolted for 4 years straight - no issues. Not really sure what your issues is, it's not rocket science and everyone does it.