I'm sure you have it figured out by now. Nice looking machine. A few things that might help, clean lead ingots, won't plug up the holes as bad. Drip deflector needs to be baby butt smooth and lubricated. I use soap stone (used for marking metal while welding) as a lubricant for the deflector. Coolant should be very close to the bottom of the drip deflector. some people use a pump to circulate the fluid to keep it cool and full to the rim of your container. your drip container placed inside a bigger container so overflow will run out and be caught by larger container. (which also keeps the deflector to coolant distance the same throughout entire batch). I use a tall ammo can inside a shorter wider one. The tall can lets the lead cool before it hits the bottom so it doesn't clump together. (Then I use them to store the components in while not in use). I believe they are 30mm and 60mm. water cools it down too fast causes pitting and bubbles on each lead ball. a few choices of coolant include undiluted RV antifreeze, automatic transmission fluid, or my favorite liquid laundry softener undiluted of course. It is water soluble, cleans up easy, and smells good. I buy it at the dollar store. I have had real good luck using these methods.

I'm sure you got it figured out by now. Higher heat and more lead to make pool deeper. Leave the oxide alone. Once it films over the lead underneath stays clean and flows smooth.

great work guys, you're going to get there don't give up!

Gantz4 was pretty much right on. 1. angle of drip is too steep 2. cover the drip pan with soapstone. 3. Much too high of a drop. 4. Drop should be about 1/2". 5. Use liquid soap to drop the hot shot into. 6. We used copper tubing coiled in the soap hooked to cold water. It helps remove the heat from the soap.

Do you have any updates on your shot maker? It would be nice to see some of your design criteria for this project. Thanks for the video.

Great job! Maybe try using fabric softener as your cooling medium so it doesn't slash. But I love the design of the shot maker. You could patent it and sell those. Amazing!

ive seen high temp copper grease used on the ramp/deflector....also fabric conditioner used as a coolant as it doesnt splash

Ive been using rv coolant. Like you would use to winterize a rv pink stuff works well

cool shotmaker ! Are you able to tell me if your drippers are made in brass ? Do you know if brass drippers will works ?

Congratulations, nice setup! Which diameter have you drilled the drippers and what's the resulting shot #?

You can make the lead run faster if you heat the drippers with a propane torch. Use soapstone on the ramp so lead won't stick to it. Use hot water (not too hot) in your collection bucket to get round shot.

Okay, I've been looking around on how to make one of these drippers. My main issue is finding how to make the bolts. Do I need to buy them? If anyone has a link to a tutorial of some kind I would greatly appreciate it.

You need a tube for overflow of the soap as the lead fills the bucket. I used a round colander to rinse the lead and to sort the shot. Perfect shot will easily pass through the colander (spaghetti strainer) but any little imperfection will not pass through. We bought wheel weights by the 55 gal barrel and used two weed burners for heat. Melting pot held about 400 to 500 pounds a time. A 55 gal barrel will give you two 5 gal buckets of the steel part of the wheel weights and the occasional valve stem (really stinks). A chunk of bees wax was used for fluxing. You flux and clean the lead BEFORE the lead hits the shotmaker or real problems if you plug the drip holes. Your heat source in the shot maker is NOT producing enough heat.

Can I suggest melting lead in a separate pot and filling up your tray that way you can skim the dirt off and have nice clean lead for pouring. works for me making slingshot ammo for moulds.

To do it like this, you need really clean led ingots. Nice video othervise

how many inclines were given to the plate

The angle on the front plate is too steep and the drop into coolant is too high. The lead rolling across the front plate is what makes it round. The front plate should be mirror smooth and just enough angle for the shot to roll off. The drop into coolant should be immediate to not allow the shot to deform into a teardrop from gravity. The coolant tank should be deep enough for the shot to be solid before it touches the settled shot.

if you take a small torch like a benz o matic and preheat the driping bolt heads as you melt the lead you should not have any problems, hot lead and water can be very dangerous . be safe and happy new year,,

Did it make good round shot? Nice video

you need a primary heating pot , so you can flux it and pull the dross. then into your awesome dripper.

Is that pure water only you've use a coolant?

The roll plate needs to be hot as well, this I know. My issue is they flatted when they hit the liquid.

Do the dripper nozzles have to be brass or can they be regular steel bolts?

voce poderia me dar alguma explicaçao sobre como fazer esferas de chumbo

Hola me puedes ayudar con las medidas de los agujeros en las tuercas

put powdered or spray graphite on the drippers and ramp,good job making prob30_50 lb,hr

ive heard of people coating with copper grease

Please do an update. Please.

Might have to hit those bolts with a little bit of fire to heat them up a bit more

GOOOOOOD JOBBB

What make is this aka the manufacturer

Nice work I need me one

take a graphite pencil and full coat the drip lip it will keep the lead from sticking

Have you thought of using a shot tower? It would simplify the process.

I’ve seen some really scary things happen when molten lead comes into contact with water...

You have to grab a torch and heat the orifices in the front that'll help all the stuff you got clogged in there come out

ola boa noite preciso de uma forma dessa vc pode me ajudar sou do brasil

Graphite from the feed store on your drip plate.

Drop a little bit of beeswax in your lead or you could use candle wax. Also with my lee lead pot I use a paper clip to unplug the discharge hole 🕳.

I would like to buy one please or release the specs so I can make one

Hey Butch , be still with the camera

Copper grease instead of silicone on the plate will solve the problem.

chalk for a black board on ramp , lead needs to be over drip bolts ,, and stop hitting it ....

SCIENCE!!!!

Оксидную пленку целый день будеш снимать лутше не трогай в закрой крышкой от кислорода

Hmmm. Safety first hey?! Melting lead with a single glove for PPE. No face shield, eye protection or respirator mask. At least you’re wearing shoes but it’s not a great idea for a pregnant woman to be inhaling the fumes of melting lead... it’s not the best product to have in your system.

you really should be wearing masks