Thank you! Especially showing the answer in the beginning but then how you got to the conclusion.

Thanks for a great video and especially for putting the solution at the beginning. It’s amazing to me how your diagnosis was exactly the problem I and others had. I already had a Black Friday deal in the cart from Home Depot, so you literally saved me $800. I may try the silicon solution that was mentioned because I do see a crack at the end of the seal.

Huge thanks Sir. This was my problem exactly and had never though to look before you. Thank so much! Just like you my dishwasher is good to go now after a couple times making sure the seal met heat while also flipped the right way. I hope more GE dishwasher owners see this before replacing door seals and entire units, because it was astonishing how simple/convincing this was, even before I tried it.

I have that door part 2 on list GE dishwasher my brother put extensions on both sides for that flap since it's not a part you can get. It's been riveted on and part of the door. Mine is still leaking but you've give me some ideas.... Thanks. You are very analytical person, patient, and somewhat relentless! Good for you.

Thanks for showing me how to fix the leak in my dishwasher

This was great thank you. I like your step by step diagnosis. Worthy of a subscription!

Just wanted to come back and say thanks! Just needed to bend that bottom seal back into place.

Thank you so much!!! I am a repar technician I this definitely stumped me!!!! Awesome 5 starts!!!

My leak was from the exact same problem your’s had with the lower seal curling in on the right! Your fix seems to be working for me as well. Thank you!!

God bless you, sir. My problem wasn't at all what you described, but I doubt I would've ever found it if I hadn't watched your video. Thanks! :)

Great video, brother. Determination and perseverance are Omni Potent.

Thanks for making the video. At first I noticed that flap was the culprit as well and adjusting it helped. Now, unfortunately, the flap is split open on both ends and water is getting out. Plus, the inner door part itself is now discontinued and seeing the inner bits made me realize it’s not something I want to tackle. Time for a new dishwasher 😢 just sucks that it’s 10 years old and it still works well.

First, this video DESERVES a hell of a lot more likes than it has. We have a GE portable that is over 20 years old, but actually was hardly used. In fact, over the last 15 years, it was used maybe 5 times (ish). But now, we've decided to start using it again and wouldn't ya know it, there's a very slight leak at the door. However, it seems to be almost dead center. I haven't done the maintenance on it as yet, but using my fingers to feel the rubber seal at the bottom, it doesn't feel right. I don't know if there's a split in the seal or if it's by design that it's one long piece, placed at the bottom and is supposed to overlap. After we get all the "spring stuff" done, I plan on rolling it outside into the bright sunlight and seeing if I can remove the entire door (without screwing up the whole thing) to get a better look at that seal. That bottom seal is exactly where the inner tub's "lip" meets the door. Fun times.

This was fantastic, thanks for the detailed video

I had an old model GE that they installed improperly and it leaked undetected for weeks in a manufactured home. My floor had ro be replaced. After they resolved the issue, the dishwasher lasted 18 years!!!!

That model caused so much trouble for us.. If you want to steer clear only use normal wash & no other fancy functions like sanitize or heated dry.. it will warp & destroy the cheap components it’s made with.. Thanks for the video though though. Obviously, we’re back to fixing it.. again for the forth time with different issues all the time.. I think we’ll toss it to recycling & get a Bosch 500 or 800. Heard repair techs only buy those cause they never get service calls for them

This video help me see the vent motor and how to get to it to replace. My GE vent motor makes noise as though the motor is stuck

Same issue. Also i fell on the dishwasher door,so now it’s leaking, and the flaps were lose, and not facing the right way.

I have similar issue but it was cut with some gap, how to replace whole flat one

5 common causes of leaks: spraying blade, gasket 1/2, water valve or float valve or missed placed plate.

What an excellent video! I have the same bottom seal problem on my GE Profile Dishwasher. Could you explain how you were able to bend the bottom seal back into the correct direction. I would appreciate learning the steps.

Good video....thanks for posting

Thank you 🙏

Thank you so much for your video! My right side flap is also "reversed" but it looks intentional. I wonder if facing inward matters, or if it just lost its usual tight seal against the bottom of the tub. Given how the seal is curling on the right vs left side, I would have guessed it is somehow intentional and the gap in the seal just widened over time and that your adjustment just retightened the seal. I don't know. It's pretty tricky to actually force it inward without taking the door panel off but I like another commenter's idea of sticking a sponge in there and turning on the heat cycle. This does seem like a design flaw. I am also going to try to angle the dishwasher up slightly and I already replaced the gasket to ensure that wasn't the issue. I found it odd that it only happens to us about 3/4 of the time, but your turbulence theory is interesting as that would indicate the plates may be arranged in such a way so as to reduce turbulence for the remaining 1/4 of the time it does not leak.

very helpful, thanks

Thank you.

Great Video Thanks how did you reverse the flap, ours is folded over on 1 side and I can't seem to grasp it Thanks

Do you know how to get off that bottom flap? Ours is cracked and doesn’t seal. It seems like there are screws or something holding the seal on but are covered in buildup.

Mine is making a crazy metallic grinding noise while it washing, I have a feeling my problem is way larger than all these superficial things

What does model # GU 1500XTL53 look like inside

Hi - very nice & informative video...our dishwasher is leaking (from underneath) from that dome-shaped part (minute 3:44 on video...what is it called?) that is located on the lower left corner of the bottom of the dishwhasher, I suppose I can replace that? (already looked underneath where leak is & looks like I should be able to replace that?) Thx.

May at some point need to replace that bottom gasket. GE website does not say what part number that is for my model.

UNIT not level top leaning out 1.5 in and bottom .5 in level to the cabinets not holding water level.

Good stuff

I had nearly the same model and have the exact same issue and I noticed the rubber door flaps on both sides are warped so I am not sure how you got it back to the correct position.

Was the silicone food safe?

10:05 Meow!😺

GE model 575-0 water leaking

Mines leaking and squeaking

You were overthinking wayyy too hard

Hi.

:D