Fixing a Smokey diesel, Freelander TD4 with BMW M47 engine, my story

No video

Fixing a Smokey diesel, Freelander TD4 with BMW M47 engine, my story

Рет қаралды 111,792

Күн бұрын

This is a story of all of the tests and fixes involved in fixing the poor running and smoke coming from a landrover Freelander with the BMW TD4 Diesel engine.
This video shows the general diagnosis and tests with the detail of the individual tests separated off into separate videos, as in this list (some additional ones in this list as well, not mentioned in video):
Crankcase filter upgrade to cut smoke, plus a full service kit:
ebay UK here: ebay.us/PocYh8
ebay USA: ebay.us/grdf4c
Changing the MAF sensor and fitting a Synergy tuning box:
• Installing a Synergy2 ...
Changing the LP fuel pump and fuel filter:
• How to Change the Fuel...
Changing the crankshaft sensor:
• Freelander. Car won’t ...
How to clean the intercooler to cut smoke:
• How to Clean the Inter...
Pressure /testing the turbo hoses and intercooler:
• Lost power? Smoke? - H...
Removing, stripping, cleaning injectors:
• Bosch common rail inje...
Fixing the engine temperature and heater being too cold:
• Engine too cold? - Qui...
Fixing the HP fuel pump regulator:
• Fixing the HP Fuel Reg...
Testing the MAP sensor:
• How to Test a MAP sens...
Testing and stripping down the Turbo Boost Control solenoid:
• How to Remove, Strip a...
Making and fitting a simple Turbo boost controller and boost gauge:
• A simple Turbo Boost C...
This is the playlist of all these videos related to fixing a smokey diesel freelander td4:
• Fixing a smokey diesel...
And this is a playlist of all my Freelander fixing videos:
• Land Rover Freelander DIY
Some useful bits to buy:
A service kit from ebay UK ebay.to/2He01xB
The new PIERBURGH MAF and tuning box is here: ebay.to/2UkEaIv
A Haynes workshop manual can usually be found cheap on ebay UK:
ebay.us/nJZ3K9
That HG stove cleaner spray shown in this video:
Amazon uk: amzn.to/2SXg0FS
Rubber disposible gloves are also useful, to start you off here's the links for
eBay USA: ebay.us/GGqmTJ
eBay UK: ebay.us/cE1BHK
Amazon UK: amzn.to/3aikbl8
Amazon USA: amzn.to/3cdwjpD
Amazon Canada: amzn.to/2Q0VHZm
Amazon Australia: amzn.to/2QlUawX
Subscribe to the channel for similar DIY, fixing stuff, car bits and tech reviews here:
www.youtube.co...
Note, if you want to be notified of new videos click on the bell symbol on my home page.
See other videos on my channel here:
/ comeinhandynow
If anyone wants to show appreciation for any money savings, or just help support the channel and future videos then you now can. Use this link: paypal.me/comei...
OR you can support me by using the Amazon and Ebay links to buy other stuff that you would usually buy, it will not cost you anything more, but will help this channel. e.g. Generally useful stuff:
Face mask:
Amazon UK: amzn.to/2GHE9d6
Similar ones on Amazon USA: amzn.to/2IHmip1
Eye goggles: Amazon UK: amzn.to/2IUSqos
Amazon USA: amzn.to/2GAtIXJ
Rubber disposible gloves:
ebay USA: ebay.to/2Aorefi
And eBay uk link: ebay.to/2AlTPSx
Or Amazon UK: amzn.to/3aikbl8
Amazon USA: amzn.to/3cdwjpD
A set of precision screwdrivers:
Amazon UK: amzn.to/2W311si
Amazon USA: amzn.to/2Z322T5
Torx bits sets:
Amazon UK: amzn.to/2Pgmf48
Or Amazon USA: amzn.to/2XlOK3h
I’m on Facebook here: / comeinhandynow
Become a Patron to get extra content or previews or sponsor here: www.patreon.co...
The video is about my personal opinion and experience and contains no paid for product placements. No responsibility is accepted for any perceived recommendation for or against a product or feature nor any consequential damage or harm since this video is just my personal experience. You accept by watching this video that you accept any responsibility for any subsequent actions or decisions that you take.
Note on copyright / licensing: This video was created using Apple iMovie and as such any music or video content is fully licensed by their terms and conditions for free publication and distribution.
See the Apple iMovie software license agreement at:
images.apple.co...
Which states "all Sample Content included in the Apple Software may be used on a royalty-free basis in your own video projects"
Additional background music free used royalty and copyright free (no copyright songs) from the following source:
Et_Voila from youtube free audio tracks

Пікірлер: 127

@TPaolozzi 3 жыл бұрын

very informative and in depth tutorial and probably the best ive seen, as i do work on a friends td Freelander occasionally ive picked up alot of helpful advice and tips, well done, great tutorial.

@comeinhandynow 3 жыл бұрын

Thanks. Glad you liked it.

@malcolmyoung7866 4 жыл бұрын

Have done most of what you have shown in the video...small amounts of work that together have taken up a bit of my time. Regards smokey exhausts etc mine was also connected to lack of power and almost deadly lack of power when pulling away at junctions...but intermittent as well...so difficult to predict. After doing a leak back test I replaced an injector (not enough cash to replace them all) and also all the rubber hoses with silicone hoses. This made a great difference but still had a lack of power. I then invested some cash into a new wiring loom between the fuel pressure sensor and the ECU. This cured the issue of power immediately. The TD4 and that engine have many well documented 'fixes' that are mainly down to lack of maintenance by both previous owners and garages that do not know of the more specific and in-depth servicing needs of that engine. The PCV filter being a major cause of the 'smoking' issue that can lead to turbo seal failure. I have changed the filter for the 'upgraded' BMW part but to be honest, if you are a 'spanner wilding' nut then just replace the original filter yearly. Many people I correspond with online have tried the BMW upgrade and have reverted back to the original filter set up...Things I need to do are cleaning the intercooler but otherwise the engine is running okay. Normal maintenance excepted, ATM the fuel tank cradle is getting replaced and all the rear bushings on the suspension removed and replaced an metalwork de rusted/shot blast and resprayed...rear diff seal replaced and fresh diff mounts and obviously new oil etc. I could go on....

@comeinhandynow 4 жыл бұрын

Nice to read you maintain it well. I can’t remember if I mention that wiring look issue in my videos, but well reminded of something else to check. As you hint at the key is good maintenance but at a low cost, as there is no point spending a fortune at garages on cheap cars.

@tk4329 4 жыл бұрын

Man you spend money for another car ,that is crazy BMW rubish,what a crap

@bigbill74scots 3 жыл бұрын

@@tk4329 English. Do you speak it or just headbutt the keyboard?

@musicsavedtheworld 3 жыл бұрын

This and all associated videos are an absolute gem! what a life saver so far !!

@comeinhandynow 3 жыл бұрын

Thank you very much.

@spadge34 9 ай бұрын

Love the random spray cleaning techniques. Really good vid, backs up my own ideas for mending stuff. Nice one!

@comeinhandynow 9 ай бұрын

Thanks!

@Augvald 2 жыл бұрын

Excellent job. Thank you for taking the time, and sharing this Master class DIY in this topic.

@comeinhandynow 2 жыл бұрын

Cheers

@ashy1423 4 жыл бұрын

Great in-depth video and add ons. Thanks for this. Stay well. Ash 🏴󠁧󠁢󠁳󠁣󠁴󠁿

@comeinhandynow 4 жыл бұрын

Thanks

@BeTep_jlepeMeH 3 жыл бұрын

Nice! I’ve been looking for a long time for that kind of explanation.. and here it is! Thank you for a detailed information!

@comeinhandynow 3 жыл бұрын

Thanks

@colmduggan7649 3 жыл бұрын

Excellent stage by stage fix for this, Very handy Thanks.

@comeinhandynow 3 жыл бұрын

Thanks, glad you liked it.

@Gandobilis Жыл бұрын

It was very helpful for me, I have E46 318d.

@comeinhandynow Жыл бұрын

Cheers

@sidnteixeira2924 2 жыл бұрын

amazing, thank you for the video

@comeinhandynow 2 жыл бұрын

Cheers

@jayxunderwood 4 жыл бұрын

Nice and clear presentation with a step by step process, I envy you. Subscribed :)

@comeinhandynow 4 жыл бұрын

Thanks!

@damiansimpson5183 3 жыл бұрын

Great. Half the BITS we want to see done on another video. Don't like this hassle. Back to other people who don't just point at Filter area & don't actually show filter & where it hangs or clips ( as I have a small filter with no end on it at the back of main Air filter box but had to clip it myself & still don't know if another tube connects to other end of once CLAY FILLED 1 inch fuel filter shaped thing, or if it just OPEN to air. Thank you for not a lot I didn't already do the hard way without introducing MOISTURE TO INSIDE OF ENGINE/ CHEMICALS TO CLEAN LUBRICATING OILS AWAY FROM PISTONS ;-) I know more oil but STILL. Clean EVERYTHING else up & then get NICE & HOT. THEN GIVE HER A GOOD HIGH REV THRASHING to BRAKE off carbon deposits = AS ENGINES WAS DESIGNED TO DO. With an additive in the tank ;-)

@comeinhandynow 3 жыл бұрын

Well, where do I start?! The small filter at back of air box is the open to air (no tube on one end) filter for the turbo control solenoid. I’ve another video on the turbo solenoid strip down where it is probably mentioned. That carbon on the inlet manifold won’t burn off with running hot, it doesn’t get hot enough. Adding a fuel additive won’t touch it either as the diesel doesn’t touch that area, diesel is injected straight in the combustion chamber. For your in capitals comments about moisture and chemicals, it is misguided. Water injection and (methanol injection) has been used for a long time on cars and steam is a combustion byproduct anyhow so a bit more steam does no harm, I believe. The piston rings are lubricated from underneath and a small amount of chemical cleaner for a short time makes little difference compared to the fire of combustion over years. Keep discussions civil please.

@SomeMadRandomPerson 4 жыл бұрын

Great video 😎👍🏻

@comeinhandynow 4 жыл бұрын

Cheers.

@patrickbarrett3571 2 жыл бұрын

Can I just say how informative your videos are. You do know these cars inside out. Would you go through diagnostics for my 2006 Td4 as I am sure I would not be as thorough. Thanks. Patrick

@comeinhandynow 2 жыл бұрын

Thanks. Sorry I just do DIY advice. Good luck!

@gerryr1893 3 жыл бұрын

Looks clean a good paint correction she would look good

@comeinhandynow 3 жыл бұрын

I think so too!

@farahoni1 2 жыл бұрын

Thxxxx you🥰

@daysofgrace2934 3 ай бұрын

If you have diagnostic machine that can do an injector balance test, to show that all the injectors are injecting the correct diesel quantity...

@markraptor50 4 жыл бұрын

I had big clouds of heavy blue smoke on cold start up.. turned out to be cylinder 2 injector leaking

@comeinhandynow 4 жыл бұрын

glad you found the cause, well done.

@sheffielduk3428 Жыл бұрын

How much was it to fix???

@davidbrits2432 Жыл бұрын

I am following your guide right now, I would like to know if I take off the inlet manifold would I not need to replace the gaskets

@comeinhandynow Жыл бұрын

I didn’t, it was a while ago that i did this but from memory I don’t remember the need to buy any gaskets so probably just rubber seals that can be reused.

@davidbrits2432 Жыл бұрын

@@comeinhandynow thank you for your reply. Out of curiosity do you still drive the Freelander 1? My wife's LR now has 246000km.

@spencerburrows3525 7 ай бұрын

My mgztt with m47 doesn't get used much. It has 55000 miles fsh. However, when started from cold it smokes. Once revved a bit and left running it clears. Or turn engine and let it tick over for 5-10 mins it doesn't smoke or at least can't see. What do you think?

@comeinhandynow 7 ай бұрын

Probably carbonised up inside so if you want it fixed I can only recommend following my steps in the video.

@bonniemcquillan45 9 ай бұрын

Hi, I'm after some advice please. I have a land rover freelander 2 SD4 Auto Sport 2011 with the haldex diff, it is now whyning could i turn it in to a 2 wheel front drive and would that take the load of off the rear axle? would I need to disconnect the electrics from the haldex? would there be any repercussions from this? any help would be much appreciated Thanks

@nemanume 3 жыл бұрын

I went to see a car like this , the car was build in 2006 and it doesn't have a trip computer or esp , how come ?

@comeinhandynow 3 жыл бұрын

Has a trip mileage recording but not mpg etc. Just the way things were back then. Didn’t have or really need esp either. Has traction control, not just to avoid spin but to aid 4x4 traction by using abs to pulse on individual wheels that spin, plus abs and hill descent control (speed limiting down steep hills using individual wheel braking), so quite good overall.

@nemanume 3 жыл бұрын

@@comeinhandynow Yeah but strange cuz it doesn.t have mpg , bmw 3 series with the same engine from 1999 they have mpg.

@williammarriott4991 4 жыл бұрын

Hi, My Freelander, 55 reg, has left me very puzzled? pretty done everything as shown on your video. The symptoms and prognosis at 110k mileage. Very poor starting, when engine is hot or cold, fires immediately turning the key but very lumpy, 1/2 RPM idle, no throttle response, then dies. Second or third attempt starts like there was no issue but loads of blue smoke for a short period, 5 secs or so then runs as normal. Turbo air outlet dry but the rest of the intake is wet when removing the tube after the inter cooler? Pulls very well when driving, 450 miles to a tank, does not use oil, turbo changed at 68k (apparent manufacturing defect!) otherwise well maintained and serviced regularly. Any advise would be greatly welcomed.

@comeinhandynow 4 жыл бұрын

wet intake very odd, try and get to the bottom of that. poor starting could be poor or blown glow plugs. otherwise check injector spray patterns and leak back plus high pressure sensor voltage.

@malcolmyoung7866 Жыл бұрын

Hopefully you managed to sort out your lumpy running engine and poor starting. It maybe you injectors are leaking into the cylinders and this may be causing the initial start and lumpy running issues.

@binarymalehim 4 жыл бұрын

Question, I have fitted a vortex upgrade thoroughly cleaned the intercooler system with new pipes cleaned manifold including the sensor it's had new injectors and regular cleaning of injectors new heater plugs EGR blank new oil new starter lots of new bits and tests and tomorrow going into have a new turbo fitted. All this done but still have a heavy vibration when in park (auto box) and under acceleration and noticeable vibration sound almost like piston slap but I know it's not that any ideas? I will follow the steps in this vid when the weather gets better as I've no garage but would like an opinion if your willing to help a frustrated TD4 owner. And white smoke on start up but not any noticeable smoke when driving.

@comeinhandynow 4 жыл бұрын

The question is whether the vibration is caused by some unbalanced part (I have read that the rubber in the crank pulley can let go, it’s a dampened pully design - worth checking) or whether it’s caused by uneven running/misfire. You could try disconnecting each injector in turn. If there is one that doesn’t change the engine revs then that injector or cylinder could be the problem one. To avoid damaging the drive electronics when you disconnect the electrics to an injector, plug the wire it into a spare external injector.

@gepwxaqdfsidsesg1548 4 жыл бұрын

@@comeinhandynow I had the same problem. I bought a leak off test kit and found one injector was leaking off twice as much as the others. Changed that injector and now it's much better.

@beverleydoughty8663 4 жыл бұрын

binarymale him p

@onurboyludag3259 2 жыл бұрын

I have a 2003 model td4. There is no problem when running at idle, but only between 2,500 rpm and 3000 rpm, it throws white smoke, above 3000 rpm, the smoke stops, what could be the problem, ? There is no lack of water

@comeinhandynow 2 жыл бұрын

This is exactly the subject of this video. Best to keep watching.

@sheffielduk3428 Жыл бұрын

Mine puffs abit of white smoke out on the cold Start every morning, but after 30 seconds it doesn't smoke all day at all, strange 😅

@malcolmyoung7866 Жыл бұрын

Possibly an injector leaking fuel into a cylinder. A common issue on most deisel cars/vans etc

@carpacravero7167 2 жыл бұрын

hello how are you, good day. I tell you I am from Argentina and I have an automatic free lander td4 and from one day to the next the reverse stopped working, you know what the problem could be. Thanks a lot

@comeinhandynow 2 жыл бұрын

good day to you. the most you could easily do is check the oil level in the auto box is ok and that the lever connection is ok. After that you could maybe drain the autobox and change the internal filter and oil perhaps but really you need a specialist garage that rebuilds auto gearboxes to take a look.

@motsedanielmabitsa6640 9 ай бұрын

Hello Mate. Kindly assist where to find a throttle body on freelander 1 td4 2.0 and fuel temperature sensor and speed sensor.. your assistance is highly appreciated.

@comeinhandynow 9 ай бұрын

Try eBay, rimmerbros, LANDROVER classic and an internet search

@lukeandrew6369 3 жыл бұрын

What would u say fixxed the issue then ? My car started smoking heavy white smoke I've recieved a P1195 code which is fuel pressure control valve ? I've noticed crank breather filter is soaked in oil so I've ordered vortex mod an new fuel pressure control valve hope this fixes the issue Fuel pressure control valve Crankcase breather mod

@comeinhandynow 3 жыл бұрын

Mine was fixed after all the work (the more important ones were HP regulator seal which was worn, injectors cleaned, inlet cleaned, crank filter updated, intercooler cleaned and finally to compensate for still coked up valves and intake, a mod to push in more air with the custom turbo boost controller, even the common "smoke at 3000rpm stationary issue" was gone after this). The fuel pressure regulator seal issue is a common problem. Like a lot of these direct injection bmw engines the intake manifold clogs up with oil and carbon, slowing the air intake and giving richer mixture = smoke. Everything needs a good clean out and checking over.

@lukeandrew6369 3 жыл бұрын

What would you suggest I've check all cables and connectors as well is I can without voltage ohm reader I've removed inspected visually tested injectors and spray pattern I've checked for leaks in fuel lines checked seal around gas cap and seal around in tank pump all good up till now all fuel pumps sound fine is there any way of me sending you a video ? Thankyou for your reply

@comeinhandynow 3 жыл бұрын

@@lukeandrew6369 All I can suggest is going through all the same steps as I did on mine. See all the videos in this series. The important ones are measuring the HP fuel rail sensor voltage, which checks the final fuel pressure is correct. Check the turbo air pressure (get a gauge), check the turbo control solenoid is working ok and the vacuum line is good, clean out the inlet manifold and intake tracts, and intercooler after changing crankcase filter.

@lukeandrew6369 3 жыл бұрын

@@comeinhandynow will give it a go when parts come should have crank breather mod tomorrow and new regulator by Thursday

@lukeandrew6369 3 жыл бұрын

What point did you notice it stop smoking ? Was it after u fixxed hp fuel regulator ?

@Ash281. 2 жыл бұрын

Hi iv just got a Freelander I td4 an seems to have a misfire at 2 to 2.5k an clowes of white smoke starts an drives with all power fine only dus it between that rev range any idear what cud be? Iv un plugged each injecter an it run crap so think injectors are fine

@comeinhandynow 2 жыл бұрын

I had the same issue. You need to watch this video.

@shanesyron8978 4 жыл бұрын

Hi my 2005 is blowing black smoke over 2k revs and it looses power for a second but doesn’t this in 2nd gear and up. Would you know what this could be.? Thanks.

@comeinhandynow 4 жыл бұрын

Smoke usually means not enough air getting in so check for air leaks in the air intake pipes from the turbo to engine. You could try an air pressure test on the pipes, intercooler etc, in one of these TD4 videos on my channel somewhere. Also a boost gauge is cheap and easy to fit - useful for diagnosing problems and keep an eye on your engine. A bit odd though that it is gear dependant, unless the engine movement in 1st gear is more which opens up a hole in a pipe perhaps.

@kacperzalecki969 3 жыл бұрын

Air leeks between MAF and intake valves-black smoke or/and injector nozzle leaking.

@cjason7202 Жыл бұрын

My freelander has clouds of white smoke upon accelerating , will these steps fix it ?

@comeinhandynow Жыл бұрын

White smoke could be water/steam, is it loosing any coolant?

@cjason7202 Жыл бұрын

@comeinhandynow nope not losing coolant

@cjason7202 Жыл бұрын

@@comeinhandynow it stinks of fuel

@tamekantyson6417 2 жыл бұрын

Can you show me where you plumbed your blow off valve into please

@comeinhandynow 2 жыл бұрын

I don’t think there is one, unless you know different.

@mikajones3018 3 жыл бұрын

I love you mate

@comeinhandynow 3 жыл бұрын

Thanks!

@motsedanielmabitsa6640 Жыл бұрын

Hello there. i have a bid of engine shaking when idling. and it shows an engine light when accelerating, but doesnt show a fault when been diagnosed, i am also struggling to remove a stcked injector. can you kindly advice. your assistance is highly appreciated

@comeinhandynow Жыл бұрын

Check over everything, a bit like in this video. Try another code reader and try and read when the light is on. Also check HP fuel pressure voltage/pressure and install a boost guage to check air / boost pressure or read off the obd2 scanner to try and indicate the area at fault. Google stuck injector removal.

@motsedanielmabitsa6640 Жыл бұрын

Thank you so much for the reply. With multimeter tester? do i test the HP on a fuel rail sensor or on a regulator by the pump itself? thanks@@comeinhandynow

@motsedanielmabitsa6640 Жыл бұрын

i have also managed to remove the in Injector yesterday, and thank you so much for the advice. @@comeinhandynow

@kenc4104 4 жыл бұрын

Jon, time to do a video on rebuilding a Triumph Dolomite Sprint engine eh?

@comeinhandynow 4 жыл бұрын

Ah yes, that would be nice, but that would be going back to a job I did 40 (eek) years ago! when youtube didn’t exist. The Dolomite sprint was the first ‘fast’ car that I owned. Loved it. Had to do a lot of work on it, as was the way in those days, but still have fond memories.

@kenc4104 4 жыл бұрын

@@comeinhandynow Yes, I remember, your Dolly Sprint vs my Scimitar GTE and Benny Parrott's Capri 2 litre. good times!

@comeinhandynow 4 жыл бұрын

Ah yes, that was a long time ago! Now I realise who I’m chatting to! Nice to hear from you. What cars are you into now?

@kenc4104 4 жыл бұрын

@@comeinhandynow Well, the wife has an XF with the 5.0 V8 we've had since new (2011), other than that the only cars of note are my two projects, a 56 and a 57 Chevy Belair. My daily driver is a Honda Ridgeline truck, I like it a lot, but not very interesting. Do you ever see Brian?

@comeinhandynow 4 жыл бұрын

@@kenc4104 Nice. And no, lost contact with Brian. Be nice to catch up more if you are ever in the UK, drop me a line whenever (email on channel).

@mikestorey6242 3 жыл бұрын

Hi mate can you please tell me. Were will i find the engine earth. Thanks

@comeinhandynow 3 жыл бұрын

Hi Mike, I had a look around the workshop manual but it refers to another manual, the ERL, for electrical info. So best google it or look around the vehicle or trace the earth cable from the battery.

@mikestorey6242 3 жыл бұрын

Hi 0mate can you tell me if you can split the manifold were the egf valve is bolted to. Please

@comeinhandynow 3 жыл бұрын

The inlet manifold that the egr bolts to is removeable and separates from the other engine side of the in inlet manifold, if that is what you mean. It doesn’t split any more than that.

@mikestorey6242 3 жыл бұрын

Okay thanks @@comeinhandynow

@sheffielduk3428 Жыл бұрын

I've used fuel and water to clean inlet manifold, it definitely won't set on fire will it when I put it back on? Hahahaha

@comeinhandynow Жыл бұрын

Just let it evaporate first. Prob be ok

@anderzamora6246 Жыл бұрын

Español Inglés Hola amigos tengo un problemilla tengo un freelander 1 TD4 con BMW y tengo un sonido horrible en la zona de la correa auxiliar y su tensor. Mi sorpresa es que no hay sitio ninguno para poder trabajar en la correa auxiliar y sacar su tensor. Alguien me podría indicar si hay algún truco o algún proceder que me pudieras ayudar para no tener que sacar el motor. llevamos días dándole vueltas como hacerlo .. muchas gracias Hello friends, I have a little problem. I have a Freelander 1 TD4 with BMW and I have a horrible sound in the area of the auxiliary belt and its tensioner. My surprise is that there is no place to work on the auxiliary belt and remove its tensioner. Could someone tell me if there is any trick or procedure that could help me so that I do not have to remove the engine. We've been thinking about how to do it for days. Thank you very much

@comeinhandynow Жыл бұрын

Remove the wheel and the plastic side panel (3 upper 8mm or 10mm bolts) and the lower engine cover tray.

@anderzamora6246 Жыл бұрын

@@comeinhandynow thanks so much

@user-kz4hh9xb6c 6 ай бұрын

Привет, по факту проблема не решена. Так как с завода нет никаких буст контроллеров и нет дыма никакого. Просмотрел ваши видео, все полностью, но проблема не решена. Заменил двигатель на контрактный, на родном моторе была минимальная компрессия, из за чего были коррекции положительные на форсунках……

@comeinhandynow 6 ай бұрын

The additional boost pressure I introduced compensated for the carbonised up internal inlet tracts. That in the end stopped it smoking.

@user-kz4hh9xb6c 6 ай бұрын

@@comeinhandynow получается, что если полностью очистить впускные каналы от сажи и нагара, то тогда и не нужно поднимать давление турбины. У нас в России популярная услуга в автосервисах, чистка впускных трактов с помощью ореховой скорлупы. Вы не рассматривали такой метод очистки впускных каналов?

@comeinhandynow 6 ай бұрын

@@user-kz4hh9xb6c Yes that is true. Walnut shell cleaning is a commonly needed technique on these BMW engines. Not something I was able to do myself and not willing to pay for, this fix was all about DIY at low cost.

@user-kz4hh9xb6c 6 ай бұрын

@@comeinhandynow недавно заменил двигатель. Так как на родном двигателе во втором цилиндре была минимальная компрессия. Сегодня всю ночь менял форсунки, так как делал это впервые. В результате, при заглушенном егр, на оборотах 2000 все в норме. Теперь проблема в оборотах 2900-3500. Двигатель работает неровно и дымит очень сильно. И сильные провалы в работе. Чтобы пересечь предел 3000оборотов на холостом ходу, приходится сильнее нажимать акселератор газа.

@comeinhandynow 6 ай бұрын

@@user-kz4hh9xb6c Maybe there is a problem with the turbo pressure, put a boost pressure gauge on the inlet manifold or measure the voltage at the MAP sensor.

@bencurry5295 Жыл бұрын

My one only reads 14.1 and is A1.

@comeinhandynow Жыл бұрын

If at 3000rpm fuel oressure regulator seal worn then, even though you think it’s good. Time to fix it.

@marcospoyanco477 3 жыл бұрын

lastima porque esta en idioma ingles algun dia podre entender quien lo puede traducir gcs

@comeinhandynow 3 жыл бұрын

Los subtítulos para cualquier idioma pueden ser añadidos por cualquier persona. Debes pedirle a un amigo que habla inglés y español que lo haga por ti.

@cm5841 3 жыл бұрын

In french please ;)

@comeinhandynow 3 жыл бұрын

Anyone can add french subtitles. Someone want to volunteer?

@turbocpt1 3 жыл бұрын

Congratulations. You replaced everything and did noy fix it.

@comeinhandynow 3 жыл бұрын

You didn't watch long enough! Fix by boosting air from turbo, then no smoke.

@turbocpt1 3 жыл бұрын

@@comeinhandynow it was satire. Meaning with these motors all the original fixes did not fix the problem, you had to make a boost controller to stop the smoke. Did you measure the air fuel ratio after that though?

@comeinhandynow 3 жыл бұрын

@@turbocpt1 Low AFR caused the smoke, which in turn was probably caused by valves and inlet clogged with carbon, which was compensated for by increased boost, which raised AFR and eliminated smoke.